BEGA 51 272.5 Wall Luminaire for Indoor Use Instructions
- June 13, 2024
- BEGA
Table of Contents
BEGA 51 272.5 Wall Luminaire for Indoor
Product Information
The luminaire has electronic components that are protected against overvoltage in accordance with DIN EN 61547. Separate overvoltage protection components are recommended for additional protection against transients, which can be found on the manufacturer’s website. – The installation and operation of the luminaire must comply with national safety regulations. – Only a qualified electrician should perform the installation and commissioning. – The manufacturer is not liable for damage caused by improper use or installation. – Any subsequent modifications to the luminaire should be done by the person responsible for those modifications. Product Usage Instructions: 1. Positioning the Luminaire: – Place the luminaire housing in a flat inclination angle over the fastening edge of the mounting plate. – Swing in the luminaire housing. – Align the luminaire housing and tighten the hexagon socket screw (wrench size 1.5) with a maximum torque of 0.25 Nm. 2. Optional Coloured Wall Accent: – If desired, an additional coloured wall accent can be achieved using arched wall panels made of metal. – The installation of a wall panel should always be done after the installation of the luminaire. – Arched wall panels are available as accessories and must be ordered separately. – Four finishes are available: velvet white, matt brass, velvet black, and matt copper.
- The article numbers for ordering are as follows:
- Velvet white: 13 337
- Matt brass: 13 338
- Velvet black: 13 339
- Matt copper: 13 340 3.
Dimension
Instructions for use
Application
Wall luminaire – Indoor luminaire with ringshaped light source for unshielded
and uniform light, light-diffusing silicone diffuser and metal ring. As single
luminaires or in arrangements, they are creative lighting design solutions for
interior design.
Product description
Ring made of metal and luminaire housing made of synthetic material, finish
colour velvet black Round inlay made of metal, finish colour velvet black
Diffusor made of translucent ageing-resistant silicone Mounting plate with 2
fixing holes ø 6 mm · 85 mm spacing 2 cable entries for through-wiring of
mains supply cable ø 7-10.5 mm, max. 5 G 1.5@ Connecting terminals 2.5@ Earth
conductor connection 2-pole connection terminals for digital control LED power
supply unit 220-240 V x 0/50-60 Hz DC 176-275 V DALI-controllable Number of
DALI addresses: 1 Basic insulation is provided between the mains and control
cables BEGA Thermal Control® Temporary thermal regulation to protect
temperature-sensitive components without switching off the luminaire Safety
class I c – Conformity mark Weight: 1.0 kg This product contains light
sources of energy efficiency class(es) D
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e. g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at
www.bega.com.
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
- Lamp
- Module connected wattage 23.2 W
- Luminaire connected wattage 26.4 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 50 °C.
- 51 272.5 K3
- Module designation LED-1402/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 3600 lm
- Luminaire luminous flux * 2265 lm
- Luminaire luminous efficiency * 85,8 lm / W
Installation
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping. Undo the
hexagon socket head screw (wrench size 1,5 mm) and remove mounting plate from
luminaire housing. Pass the power connecting cable through the cable entry in
the mounting plate. Note position of application of the mounting plate “arrow
down”. Fasten the mounting plate with the supplied fastening material or other
suitable fastening material to the installation surface. Establish earth
conductor connection to the earth conductor connection screw and make the
electrical connection to the terminals. The two connecting terminals marked
DA, DA are provided for digital control purposes. If these terminals are not
assigned, the luminaire will work with full light output. Insert the
connection terminals into the luminaire housing.
Position the luminaire housing in a flat inclination angle over the fastening edge of the mounting plate and swing in. Align luminaire housing and tighten (max. 0.25 Nm) hexagon socket screw (wrench size 1.5). If an additional coloured wall accent is desired, arched wall panels made of metal are optionally available – accessories.
Please note: The installation of a wall panel should always be carried
out after the installation of the luminaire.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire. The
light colour and light output of BEGA replacement modules correspond to those
of the modules originally fitted. The module can be replaced by qualified
persons using standard tools. Disconnect the system from the power supply.
Undo the hexagon socket head screw (wrench size 2.5 mm) and remove luminaire
from mounting plate. Remove the connecting lines from the terminals and place
the front of the luminaire on a soft surface.
Open the luminaire housing:
First loosen the two outer Torx screws (T20), then the 4 inner Torx screws
(T20). Disconnect the lines of the luminaire cable from the 4 terminals and
remove the terminals. Using a suitable tool (or with thumb and forefinger),
apply pressure to the four snap-in hooks of the luminaire housing until the
housing base releases from the latch. Remove the LED module with the diffuser
from the holder. Install the replacement module. Please follow the
installation instructions for the new LED module. A defective LED-module
(silicone diffusor) must be replaced. Close the luminaire housing: Place the
lower part of the housing on the snap-in hooks of the upper part of the
housing and snap it into place with pressure. First tighten the four inner
Torx screws (T20 max. 1.2 Nm), then the two outer Torx screws (T20 max. 0.35
Nm). Re-attach the terminals to the wires of the luminaire cable. Make the
electrical connection to the terminals. Observe the correct configuration of
the connecting cable. Connect the live conductor to the brown wire (L) and the
neutral conductor to the blue wire (N). The two connecting terminals marked
DA, DA are provided for digital control purposes. If these terminals are not
assigned, the luminaire will work with full light output. Position the
luminaire housing in a flat inclination angle over the fastening edge ofthe
mounting plate and swing in. Align luminaire housing and tighten (max. 0.25
Nm) hexagon socket screw (wrench size 1.5).
Accessories · Wall panels
For this luminaire, optional arched wall panels made of metal are available in
4 finishes. Wall panels are accessories and must be ordered separately.
- Colour velvet white 13 337
- Colour matt brass 13 338
- Colour velvet black 13 339
- Colour matt copper 13 340
Spares
- LED power supply unit DEV-0402/700i
- LED module 3000 K LED-1402/930
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>