BEGA 99 331 Wal Ceiling Light LED Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
99 331
**In-ground luminaire
**
99 331 Wal Ceiling Light LED
Instructions for use
Application
Location luminaire for recessed installation in compacted surfaces with ø 70
mm provided by the customer.
Drive-over luminaire from vehicles with pneumatic tyres.
Please note:
Product description
In-ground LED luminaire without power supply unit
Luminaire made of stainless steel
Steel grade no 1.4301
Installation bush made of polyamide
Safety glass, white
3 m water-resistant connecting cable
05RN8-F 2 × 1◻ with implemented water stopper
Safety class III
Protection class IP 68 20 m
Dust-tight and water pressure tight
Maximum submersion depth 20 m
Not suitable for permanent operation under water
Impact strength IK08
Protection against mechanical impacts < 5 joule
– Safety mark
– Conformity mark
Weight: 0.8 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Lamp
| Module connected wattage | 1.2 W |
|---|---|
| Luminaire connected wattage | 1.6 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 65 °C |
| When installed in heat-insulating material | ta max = 60 °C |
99 331 K27
| Module designation | LED-0331/827 |
|---|---|
| Colour temperature | 2700 K |
| Colour rendering index | CRI > 80 |
| Module luminous flux | 240 lm |
| Luminaire luminous flux | 53 lm |
| Luminaire luminous efficiency | 33,1 lm / W |
99 331 K3
| Module designation | LED-0331/830 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 80 |
| Module luminous flux | 245 lm |
| Luminaire luminous flux | 54 lm |
| Luminaire luminous efficiency | 33,8 lm / W |
99 331 K4
| Module designation | LED-0331/840 |
|---|---|
| Colour temperature | 4000 K |
| Colour rendering index | CRI > 80 |
| Module luminous flux | 250 lm |
| Luminaire luminous flux | 55 lm |
| Luminaire luminous efficiency | 34,4 lm / W |
Please note:
The luminaire can only be operated with an operating device that fulfills
the requirements according to EN 61347-2-13. The maximum idle voltage of 60 V
DC must conform to SELV or SELV equivalent.
**Installation
**
A separate power supply unit is required to operate the luminaire – see
accessories.
For installation in drilled holes, a recessed opening of ø 70 mm with a
minimum depth of 100 mm is required to hold the installation sleeve.
Press the installation sleeve firmly into the recessed opening.
For installation in paved surfaces, the appropriate installation housing is 70
745 available.
In this case, the polyamide installation sleeve is not used.
The cable connection must be established on site with the correct protection
class and safety class for the luminaire.
We recommend that you use distribution box 70 730 or 71 053 for this purpose.
To protect the luminaire power supply cable against damage we recommend you to
use a PVC conduit on-site.
A 24 V safety direct voltage source with a smoothed residual ripple of max. 10
% is required for the electrical connection of the luminaire – see
accessories.
If other safety direct voltage sources are used, an upstream fuse (max. 6 A)
must be provided by the customer.
The black wire is to be connected to the negative terminal, the red wire to
the positive terminal on the power supply unit.
Press the luminaire into the installation sleeve.
Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.
Cleaning · Maintenance
After installation, the luminaire should first be cleaned. Building dust,
residues from contact adhesives, paint splashes and rust film must be
completely removed. Never use high pressure cleaners and cleaning implements
made of normal steel, steel brushes or steel wool because they cause
extraneous rust to form. When using stainless steel cleaners, please read the
directions carefully.
Cleaning agents containing hydrochloric acid and chlorides should never be
used. We recommend cleaning the luminaires regularly.
Accessories
Power supply unit for LED luminaires 24 V DC
Safety transformer according to EN 61558/VDE 0570 part 2-6
| 70 564 | Power supply unit for 5-15 W |
|---|---|
| 70 465 | Power supply unit for 10-25 W |
| 70 565 | Power supply unit for 20-35 W |
| 70 566 | Power supply unit for 30-50 W |
| 70 567 | Power supply unit for 40-75 W |
| 70 169 | Power supply unit for 70-150 W y |
| 70 114 | Power supply unit for 0-70 W |
| AC range: | AC: 198-264 V y 50-60 Hz |
| DC range: | DC: 176-275 V |
The power supply units are also suitable for the operation of several LED luminaires. In this case, the maximum wattage of the power supply unit must not be exceeded.
| 70 745 | Installation housing made of stainless steel |
|---|---|
| 70 730 | Distribution box for installation in soil with 7 cable entries |
Connection terminals 5 x 4◽
For the accessories a separate instructions for use can be provided upon request.
Spares
| Gasket housing | 83 001 363 .1 |
|---|
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
Documents / Resources
| BEGA
99 331 Wal Ceiling Light
LED
[pdf] Instruction Manual
99 331 Wal Ceiling Light LED, 99 331, Wal Ceiling Light LED, Ceiling Light
LED, Light LED, LED
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>