BEGA 50876.2 Recessed Ceiling Luminaire Instruction Manual
- June 13, 2024
- BEGA
Table of Contents
Recessed ceiling luminaire for indoor use
50 876.2
50876.2 Recessed Ceiling Luminaire
Instructions for use
Application
Free-radiating recessed ceiling luminaire · indoor luminaire with crystal
glass and aluminium alloy housing for connection to external LED power supply
unit.
For surface-mounted installation in indoor suspended ceilings of 5-25 mm
thickness.
Product description
Recessed luminaire without power supply unit
Luminaire housing made of cast aluminium
Installation housing is made of glass-fibre reinforced polyamide with 2
fastening springs
Crystal glass with bayonet closure
Synthetic lens with light-diffusing white matt finish
Ceiling trim ring made of metal, Stainless steel
Ceiling aperture ø 146 mm
Free space installation depth required 105 mm 1 connecting cable with strain
relief and plug connector system for BEGA power supply unit, on/off or DALI
Safety class III
****– Conformity mark
Weight: 1.4 kg
This product contains light sources of energy efficiency class(es) E
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
| Module connected wattage | 11.5 W |
|---|---|
| Luminaire connected wattage | 13.5 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 40 °C |
| When installed in heat-insulating material | ta max = 25 °C |
50 876.2 K3
| Module designation | LED-0800/930 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 90 |
| Module luminous flux | 1735 lm |
| Luminaire luminous flux | 1056 lm |
| Luminaire luminous efficiency | 78,2 lm / W |
**Installation
**
A separate power supply unit is required to operate the luminaire.
For connection to external LED-power supply unit – accessory 13 144 or 13 169
– the luminaire is equipped with a 2-pin connector.
Note operating instructions of the LED-power supply units.
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
The recessed opening is covered by the frame of the luminaire housing.
Fixing of the installation housing in the recessed opening is achieved by
using two adjustable springs.
Installation into inserted ceilings:
A recessed opening of 146 mm is necessary to accept the installation housing.
Recessed depth min. 105 mm.
Compress the fastening springs of the installation housing against their
spring pressure on both sides towards the housing and slide the installation
housing into the recessed opening.
The fastening springs catch the ceiling panel from the back side. Minimum
thickness of the ceiling panel is 5 mm. If minimum thickness of the panel is
less than 5 mm it must be reinforced from the reverse side. Maximum thickness
of the ceiling panel must be no more than 25 mm.
Push the enclosed threaded rods through the two inside openings of the
installation housing and guide the clamping angle of the threaded rods
downwards onto the suspended ceiling. Clip the threaded rods into their guide
grooves and screw them in by hand as far as possible. Fix in end position with
screwdriver (TX 10). This clamp fixing prevents the installation housing from
turning and dropping.
Connect to the LED power supply unit.
Route the LED power supply unit through the installation housing and place it
in the suspended ceiling.
Connect the 2-pin plug connector between luminaire and external LED power
supply unit.
Press together the two internal fixing sliders inside the luminaire housing.
Push the luminaire housing to the end of the installation housing and then
release the fixing sliders.
This mechanism ensures that the luminaire housing sits securely inside the
installation housing.
Fix crystal glass with cover ring and dispersing lens into the luminaire
housing by turning it clockwise.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by
qualified persons using standard tools.
Disconnect from main supply.
Unscrew glass from luminaire housing by turning it counter-clockwise.
Please follow the installation instructions for the LED module.
Screw in glass by turning it clockwise.
Defective glass must be replaced.
Accessories
Power supply units for LED luminaires 220-240 V · 0/50-60 Hz with strain relief and plug connector system.
| 13 144 | Power supply unit on/off |
|---|---|
| 13 169 | Power supply unit DALI |
The power supply units are only suitable for the operation of one LED
luminaire.
For the accessories a separate instructions for use can be provided upon
request.
Spares
| LED module 3000 K | LED-0800/930 |
|---|---|
| Spare glass | 75 003 976 |
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
Documents / Resources
| BEGA
50876.2 Recessed Ceiling
Luminaire
[pdf] Instruction Manual
50876.2 Recessed Ceiling Luminaire, 50876.2, Recessed Ceiling Luminaire,
Ceiling Luminaire, Luminaire
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>