BEGA 33334 LED Wall Light Instruction Manual

BEGA 33334 LED Wall Light

Product Information

The Wandleuchte Wall luminaire Applique is a wall luminaire with light emission on two sides. It provides fully glare-free light for illuminating wall surfaces and roadways adjacent to the walls. It is suitable for both interior and exterior lighting design.

The installation and operation of this luminaire are subject to national safety regulations. It is recommended to have a qualified electrician carry out the installation and commissioning. The manufacturer does not accept liability for damage caused by improper use or installation. Any subsequent modifications to the luminaire should be done by a responsible person who will be considered the manufacturer.

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. However, additional overvoltage protection components are recommended for extra protection against transients. These components can be found on the manufacturer’s website at www.bega.com.

Please avoid touching the light output opening of the LED directly during installation or relamping, as the LED components are high-quality electronic components.

Product Usage Instructions

1. Undo the screws to remove the luminaire cover and glass.
2. Lead the mains supply cable through the cable entry into the luminaire back housing.
3. Fix the luminaire base onto the mounting surface using the enclosed or any other suitable fixing material. Make sure to use the gasket rings supplied.
4. Make the earth conductor connection and the electrical connection.
5. Ensure that the gasket is positioned correctly.
6. Put the luminaire cover and glass back onto the luminaire back housing and tighten the screws evenly.

Replacement Parts:

• Ersatzglas (Replacement glass)
• LED-Netzteil (LED power supply)
• LED-Modul 3000 K (LED module 3000 K)
• LED-Modul 4000 K (LED module 4000 K)
• Dichtung (Gasket)

Dimension

Wall luminaire

Application

• Wall luminaire with light emission on two sides.
• Fully glare-free light for illuminating wall surfaces and roadways adjacent to the walls. For interior and exterior lighting design.

Product description

• Luminaire made of aluminium alloy and stainless steel
• BEGA Unidure® coating technology Crystal glass coated
• Silicone gasket
• 2 mounting holes ø 5.5 mm
• Distance apart 75 mm
• 2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm
• Connection terminal 2.5@
• Earth conductor connection
• BEGA Ultimate Driver®
• LED power supply unit
• 220-240 V x 0/50-60 Hz
• DC 176-264 V
• BEGA Thermal Switch®
• Temporary thermal shutdown to protect temperature-sensitive components
• Safety class I
• Protection class IP 65
• Dust-tight and protection against water jets Impact strength IK07
• Protection against mechanical
• impacts < 2 joule
• – Safety mark
• – Conformity mark
• Weight: 2.2 kg
• This product contains light sources of energy efficiency classes C

Safety

• The installation and operation of this luminaire are subject to national safety regulations.
• Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation.
• If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp

• Module connected wattage 3.8 W

• Luminaire connected wattage 4.9 W

• Rated temperature ta = 25 °C

• Ambient temperature ta max = 50 °C
  33 334 K3

• Module designation LED-0263/830

• Colour temperature 3000 K

• Colour rendering index CRI > 80

• Module luminous flux 755 lm

• Luminaire luminous flux 255 lm

• Luminaire luminous efficiency 52 lm / W
  33 334 K4

• Module designation LED-0263/840

• Colour temperature 4000 K

• Colour rendering index CRI > 80

• Module luminous flux 780 lm

• Luminaire luminous flux 264 lm

• Luminaire luminous efficiency 53,9 lm / W

Overvoltage protection

• The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
• To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
• You can find them on our website at www.bega.com.

Installation

• LED are high-quality electronic components!
• Please avoid touching the light output opening of the LED directly during installation or relamping.
• Undo screws. Remove luminaire cover and glass.
• Lead the mains supply cable through the cable entry into the luminaire back housing.
• Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
• Be sure to use the gasket rings supplied.
• Make the earth conductor connection and the electrical connection.
• Make sure that gasket is positioned correctly.
• Put the luminaire cover and the glass onto the luminaire back housing and tighten the screws evenly.

Replacing the LED module

• The designation of the LED module is noted on a label in the luminaire.
• The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
• The module can be replaced by qualified persons using standard tools.
• Disconnect the system and open the luminaire.
• Please follow the installation instructions for the LED module.
• Inspect and, if necessary, replace the luminaire gaskets.
• Defective glass must be replaced.
• Close the luminaire.

Cleaning · Maintenance

• Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
• Do not use high pressure cleaners.

Spares
Spare glass 11 002 766 11
LED power supply unit DEV-0303/350
LED module 3000 K LED-0263/830
LED module 4000 K LED-0263/840
Gasket 83 001 221

BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>