BEGA 24340 Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

Wall luminaire
Instructions for use
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 24340 Wall Luminaire Instruction Manual

Wall luminaire

Product Dimensions

Instructions for use

Application

Shielded wall luminiaire with high protection class.
A luminaire made of aluminium alloy and crystal glass.

Product description

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Crystal glass, white inside
Silicone gasket 2 mounting holes ø 4.8mm
Distance apart 228mm 2 cable entries for through-wiring of mains supply cable ø 7-10.5mm
Connection terminal 2.5@
Earth conductor connection
LED power supply unit 220-240 V x 0/50-60 Hz
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK03
Protection against mechanical impacts < 0.35 joule
– Safety mark
– Conformity mark
Weight: 2.4 kg
This product contains light sources of energy efficiency classes C, D

Lamp

Module connected wattage: 8.6 W
Luminaire connected wattage: 9.8 W
Rated temperature: ta=25 °C
Ambient temperature; ta max=55 °C

24 340K3

Module designation: LED-0996/830
Colour temperature: 3000 K
Colour rendering index: CRI >80
Module luminous flux: 1570 lm
Luminaire luminous flux: 913 lm
Luminaire luminous efficiency: 93,2 lm/W

24 340K4

Module designation; LED-0996/840
Colour temperature: 4000 K
Colour rendering index: CRI >80
Module luminous flux; 1650 lm
Luminaire luminous flux: 959 lm
Luminaire luminous efficiency : 97,9 lm/W

Safety
The installation and operation of this luminaire are subject to national safety regulations.

Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation.

If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

Take note of the cover frame fixing screw positions when installing the luminaire base (see sketch).
Undo hexagon socket head screws (wrench size 3 mm) up to the stop. Remove luminaire top with glass.
Undo screws key slots and remove the LEDunit.
Disconnect plug connection.
Lead the mains supply cable through the cable entry of the luminaire base.
Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied.
Make the earth conductor connection and the electrical connection.
Push plug into coupler as far as it will go.
Reassemble LED-unit and tighten fixing screws firmly and evenly. Please observe that the LED board is not damaged mechanically.
Make sure that the gasket is in correct position.
Install luminaire top with glass and tighten screws evenly.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the
LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.

Spares