BEGA 50961.2 Table Lamp for Indoor Use Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50961.2 Table Lamp for Indoor Use Instruction Manual
Table lamp for indoor use
Instructions for use
Application
- Table lamp · indoor luminaire with a light aperture of 120°.
- It is infinitely rotatable along the longitudinal axis through 360°.
Product description
- Luminaire housing and shield finish stainless steel
- Hand-blown opal glass, with screw neck
- Black cable · 2m, with safety plug
- Built-in toggle switch
- Light aperture 120°, infinitely rotatable by 360°
- LED power supply unit 220-240 V y 50-60 Hz
- Safety class I
- Conformity mark
- Weight: 3.0 kg
- This product contains light sources of energy efficiency classes C, D
Safety
The installation and operation of this luminaire are subject to national safety regulations. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
- Module connected wattage: 6.8 W
- Luminaire connected wattage: 8.2 W
- Rated temperature: ta=25 °C
- Ambient temperature: ta max=45 °C
50 961.2K3
- Module designation: LED-1117/930
- Colour temperature: 3000 K
- Colour rendering index: CRI >90
- Module luminous flux: 1125 lm
- Luminaire luminous flux: 421 lm
- Luminaire luminous efficiency: 51,3 lm/W
50 961.2K4
- Module designation: LED-1117/940
- Colour temperature: 4000 K
- Colour rendering index: CRI >90
- Module luminous flux: 1200 lm
- Luminaire luminous flux: 449 lm
- Luminaire luminous efficiency: 54,8 lm/W
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Mount glass with reflector to the luminaire housing by turning it clockwise until the stop. Turn glass with reflector counter-clockwise to bring it into the required position.
Replacing the LED module
- The designation of the LED module is noted on a label in the luminaire.
- The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
- The module can be replaced by qualified persons using standard tools.
- Disconnect the system from the power supply.
- Rotate the glass body anti-clockwise beyond the stop to open the luminaire.
- Undo the locking screw on the underside and remove the synthetic cover with switch from the luminaire housing.
- Remove the Torx screws (T10) on the right and left of the LED module completely. Undo both fastening nuts on the power supply unit holder with a box spanner (SW 7) and carefully remove the power supply unit component from the luminaire housing.
- Disconnect the wires of the LED module from the loose connection terminals of the power supply unit.
- Remove the LED module. Install the replacement LED module. Please follow the installation instructions for the LED module.
- Defective glass must be replaced. Assemble and close the luminaire in reverse order.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Spares
Spare glass 11 003 111 .1RG
LED power supply unit DEV-0136/500
Switch 63 000 360
Rocker switch 63 000 361
Switch retainer 63 000 362
LED module 3000 K LED-1117/930
LED module 4000 K: LED-1117/940
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>