BEGA 50892.1 Recessed Ceiling Luminaire for Indoor Use Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 50892.1 Recessed Ceiling Luminaire for Indoor Use
Product Information
Product Usage Instructions
DIMENSIONS
Instructions for use
Product Description
Installation
Accessories
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50892.1 Recessed Ceiling Luminaire for Indoor Use

Product Information

Product Name: Luminaire
Model Number: 50 892.1 K3
Lamp Type: LED
Module Wattage: 17.6 W
Luminaire Wattage: 20.5 W
Colour Temperature: 3000 K
Colour Rendering Index (CRI): > 90
Module Luminous Flux: 2780 lm
Luminaire Luminous Flux: 2026 lm
Luminaire Luminous Efficiency: 98.8 lm/W

Product Usage Instructions

Safety :
The installation and operation of this luminaire should be done in accordance with national safety regulations. Only qualified electricians should perform the installation and commissioning. The manufacturer is not liable for any damage caused by improper use or installation. If any modifications are made to the luminaire, the person responsible for the modifications will be considered the manufacturer.

Overvoltage Protection:
The luminaire’s electronic components are protected against overvoltage according to DIN EN 61547. For additional protection against transients, it is recommended to use separate overvoltage protection components which can be found on the manufacturer’s website.

Installation:
Connect the luminaire to the LED power supply unit. Guide the power supply unit through the opening in the ceiling and position it on the suspended ceiling. The recessed opening is covered by the frame of the luminaire housing. Use three adjustable springs to fix the installation housing in the recessed opening. Ensure that the luminaire housing and external LED power supply unit are not covered by any heat insulating materials.

Synthetic Diffuser:
Place the synthetic diffuser onto the luminaire housing and make sure that the cam pins fit into the notches of the diffuser. Screw in the diffuser by turning it clockwise to securely hold it in place and prevent vibrations. To remove the diffuser, turn it counter-clockwise.

Power Supply Units:
The power supply units provided are suitable for operating only one LED luminaire. There are two options available: on/off and DALI (Digital Addressable Lighting Interface). Choose the appropriate power supply unit for your luminaire.

Accessories:
Separate instructions for use for accessories can be provided upon request. Please contact the manufacturer for more information.

Spares:
The synthetic cover for the LED module with a colour temperature of 3000 K can be purchased as a spare part with the model number 15 000 424. Please refer to the user manual for more detailed instructions and safety information.

Ceiling and wall luminaire for indoor use

DIMENSIONS

BEGA-50892-1-Recessed-Ceiling-Luminaire-for-Indoor-Use-
FIG-4

Instructions for use

Application:
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass, satin matt and aluminium alloy housing, for all lighting tasks. They are ideal for places where a soft and uniform lighting distribution is required. Luminaire with a high protection class.

Product Description

Recessed ceiling luminaire downlight
»STUDIO LINE« without power supply unit
Luminaire housing made of aluminium inside hue white
Impact-resistant synthetic diffuser, translucent white, with bayonet closure
Recessed opening ø 280 mm
Required installation depth 145 mm
Luminaire housing with 3 fastening springs and guide screws
1 connecting cable with strain relief and plug connector system for BEGA power supply unit,on/off or DALI
Safety class III 3
– Conformity mark
Weight: 1.4 kg

This product contains light sources of energy efficiency classes D

Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Lamp

Module connected wattage 17.6 W
Luminaire connected wattage 20.5 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 35 °C

50 892.1 K3

Module designation LED-0447/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 2780 lm
Luminaire luminous flux 2026 lm
Luminaire luminous efficiency 98,8 lm / W

Installation

Luminaire housing must not be installed in heat-insulating material.
A separate power supply unit is required to operate the luminaire.
For connection to external LED-power supply unit – accessory 13 177 or 13 173 – the luminaire is equipped with a 2-pin connector.
Note operating instructions of the LED-power supply units.
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Connect to the LED power supply unit.
Guide the LED power supply unit through the opening in the ceiling and position it on the suspended ceiling.
The recessed opening is covered by the frame of the luminaire housing.
Fixing of the installation housing in the recessed opening is achieved by using three adjustable springs.
Luminaire housing and external LED power supply unit must not be covered by any heat insulating materials.

Installation into inserted ceilings:

A recessed opening of 280 mm with a minimum depth of 145 mm is required.
Push luminaire housing into the ceiling cut-out and tighten evenly screws (T 20) of the three mounting springs.
The mounting springs catch the ceiling facing from the back side. The minimum thickness of the panel must be 9 mm and the maximum thickness 25 mm. If the ceiling facing has a thickness of less than 3 mm, the facing thickness in the region of the mounting
springs must be increased from the back side.
Connect the 2-pin plug connector between luminaire and external LED power supply unit.
Unpack LED unit, lift it with enclosed gloves and insert it into the luminaire housing – keyholes – .
Turn the LED device anticlockwise until it stops and tighten the screws (T 10) evenly.
Place the synthetic diffuser to the luminaire housing and observe that the cam pins fit into the notches of the synthetic diffuser.
Screw in synthetic diffuser by turning it clockwise.
Thus, you reach a safe and vibration resistant holding of the synthetic diffuser.

To release the synthetic diffuser from the luminaire housing, turn it counterclockwise.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleaning agents to remove dirt.
A defective synthetic cover must be replaced.

Replacement of the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system.
Unscrew synthetic diffuser from luminaire housing by turning it counter-clockwise.
Please follow the installation instructions for the LED module.
Screw in synthetic diffuser by turning it clockwise.
Defective synthetic diffuser must be replaced.