BEGA 12 148 Ceiling and Wall Luminaire for Indoor Use Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

Dimension
Instructions for Use
- Application
Product Description
Safety
Overvoltage Protection
Installation
Replacement of the LED module · Maintenance
Spares
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 12 148 Ceiling and Wall Luminaire for Indoor Use

Dimension

Instructions for Use

Application

Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass, satin matt and aluminium alloy housing, for all lighting tasks.
They are ideal for places where a soft and uniform lighting distribution is required.
Luminaire with a high protection class.

Product Description

Luminaire made of aluminium alloy
Finish Colour white
Hand-blown opal glass, satin matt
2 mounting holes ø 5mm
Distance apart 170mm
2 cable entries for through-wiring for mains
cable up to ø 11 mm max. 5 x 1.5@
Connection terminal 2.5@
Earth conductor connection
2-pole connecting terminal for digital control
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-280 V
DALI-controllable
Basic insulation is provided between the mains and control cables
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 44
Protected against granular foreign bodies ≥ 1 mm and splash water Impact strength IK02
Protection against mechanical impacts < 0.2 joule
Safety mark
Conformity mark
Weight: 3.2 kg
This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage Protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp
Module connected wattage 13.2 W
Luminaire connected wattage 15.4 W
Rated temperature ta=25 °C
Ambient temperature ta max=30 °C

12 148K27
Module designation 2x LED-0262/927
Colour temperature 2700 K
Colour rendering index CRI >90
Module luminous flux 2200 lm
Luminaire luminous flux 1527 lm
Luminaire luminous efficiency 99,2 lm/W

12 148K3
Module designation 2x LED-0262/930
Colour temperature 3000 K
Colour rendering index CRI >90
Module luminous flux 2230 lm
Luminaire luminous flux 1548 lm
Luminaire luminous efficiency 100,5 lm/W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Lead the mains supply cable through the cable entry into the luminaire back housing.
Fix luminaire back housing with enclosed or any other suitable fixing material onto the mounting surface.
It is imperative to use the enclosed gaskets.
Make earth conductor connection.
Push silicone sleeves over the lines and make electrical connection.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
Insert the opal glass into the lower spring clips, centre and push it into the upper spring clips.

Replacement of the LED module · Maintenance

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the electrical installation.
Pull glass out of the spring clips and remove from the luminaire back housing.
Clean glass and luminaire regularly with solvent-free cleansers from dirt.
Please follow the installation instructions for the LED module.
Snap the glass into the lower spring clips, centralise and push into the upper spring clips.
A broken glass must be replaced.