BEGA 50840.2 Wall Luminaire for Indoor Use Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50840.2 Wall Luminaire for Indoor Use Instruction Manual
Instructions for use
Application
Free-radiating wall luminaire · indoor luminaire with crystal glass, white
inside and aluminium housing. For all lighting tasks in interior applications.
They are ideal for places where a soft and uniform lighting distribution is
required.
Product description
Luminaire made of aluminium alloy Finish Stainless steel Crystal glass, inside
white, with bayonet closure 2 mounting holes ø 4.5mm Distance apart 35mm 1
cable entry for mains supply cable up to ø 10.5 mm max. 3 x 1.5@ Connecting
terminals 2.5@ Earth conductor connection LED power supply unit 220-240 V x
0/50-60 Hz DC 176-280 V BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components Safety
class I Impact strength IK05
Protection against mechanical impacts < 0.7 joule
Safety mark
Conformity mark
Weight: 2.0 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
| Module connected wattage | 9.6 W |
|---|---|
| Luminaire connected wattage | 11.3 W |
| Rated temperature | ta=25 °C |
| Ambient temperature | ta max=50 °C |
50 840.2K3
| Module designation | 2x LED-0689/930 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 90 |
| Module luminous flux | 1560 lm |
| Luminaire luminous flux | 928 lm |
| Luminaire luminous efficiency | 82,1 lm/W |
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Undo the hexagon socket head screw (wrench size 5mm) and remove mounting plate
from luminaire housing.
Loosen earth connection (plug connection) between luminaire housing and
mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
Note position of application of the mounting plate “arrow down”.
Fasten the mounting plate with the supplied fastening material or other
suitable fastening material to the installation surface.
Make earth connection to earth screw and electrical connection to the
terminals.
Make earth connection (plug connection) between luminaire housing and mounting
plate again.
Place connecting terminals inside the luminaire housing.
Install luminaire housing onto the mounting plate, adjust and tighten hexagon
socket head screw.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
thoseof the modules originally fitted. The module can be replaced by qualified
persons using standard tools.
Disconnect from main supply.
Unscrew glass from luminaire housing by turning it counter-clockwise.
Please follow the installation instructions for the LED module.
Screw in glass by turning it clockwise. Defective glass must be replaced.
Spares
LED power supply unit DEV-0136/350
LED module 3000 K LED-0689/930
Spare glass 75 003 649
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden · [email protected] · www.bega.com