BEGA 50 916.2 Table Lamp for Indoor Use Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50 916.2 Table Lamp for Indoor Use
Dimension
Application
Table lamp · indoor luminaire with wide beam light distribution.
Luminaire for positioning on a wooden base for a variety of lighting
situations with adjustable light.
Wooden base optionally available in three different colour versions, as listed
below.
Product description
Table lamp »STUDIO LINE«
Cast aluminium luminaire housing, finish Colour velvet black, inside hue
aluminium matt
Trim ring · Chrome finish
Clear safety glass
Light-diffusing silicone lens
Reflector made of pure anodised aluminium
Cable dimmer (touch-controlled dimmer) for infinite light adjustment
Black cable · 2,5m, with safety plug
LED power supply unit
220-240 V 0/50-60 Hz
DC 196-250 V
Safety class I
– Conformity mark
Weight: 1.8 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national safety regulations. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components. You can find them on our website
at www.bega.com.
Lamp
Module connected wattage: 11.5 W
Luminaire connected wattage: 13.5 W
Rated temperature: ta=25 °C
Ambient temperature: ta max=55 °C
50 916.2K3
Module designation: LED-0978/930
Colour temperature: 3000 K
Colour rendering index: CRI > 90
Module luminous flux: 1735 lm
Luminaire luminous flux: 1072 lm
Luminaire luminous efficiency: 79,4 lm/W
Installation
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
For precise positioning of reflector and cover ring, it is advisable to lift
the luminaire at the connecting cable. The opening of the luminaire housing
points downwards.
Screw enclosed trim ring with attached reflector into the luminaire housing by
turning it clockwise.
Position luminaire on the separate wooden base. Insert the connecting cable
into the groove of the wooden base.
For this purpose, wooden bases in three different surfaces are available –
accessories 13 209, 13 208 and 13 277. Connect luminaire to mains supply (230
V).
Press sensing device gently to turn the luminaire on or off.
Holding the sensing device enables to adjust the light intensity infinitely.
Set the desired beam direction by tilting the luminaire.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
We recommend that you dry-clean the sensing device.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by
qualified persons using standard tools.
Disconnect the electrical installation. Open the luminaire.
Please follow the installation instructions for the LED module.
Close the luminaire.
Accessory · Wooden bases
For this luminaire wooden bases in 3 surfaces are optional available.
Wooden bases are accessories and must be ordered separately.
Natural oak: 13 209
Ash black: 13 208
Ash white: 13 27
Spares
Glass/Trim ring: 20 000 042 B4
LED power supply unit: DEV-0305/350
Connecting cable with dimmer: 62 001 185
LED module 3000 K: LED-0978/930
Reflector: 75 002 766
Customer Support
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden · info@bega.com · www.bega.com