BEGA 50 714.4 Recessed Ceiling Luminaire for Indoor Use Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
35.22 · Technical amendments reserved
50 714.4
Recessed ceiling luminaire for indoor use
Instructions for use
Application
Pivoting recessed ceiling luminaire · indoor luminaire partially satin matt
crystal glass inside and aluminium alloy housing.
Efficient luminaires for adjustable, brilliant light in the residential living
space and for use in many other ranges of interior illumination. For
installation into ceilings with a shallow depth in interior areas.
Product description
Recessed ceiling luminaire »ACCENTA VARIO«
Die-cast aluminium housing
Crystal glass, partially satin matt inside
Reflector of anodised pure aluminium
Ceiling trim ring finish, Brass
Recessed opening ø 95 mm
Required installation depth 60 mm
Fixing is achieved by using
2 adjustable claws
External LED power supply unit
220-240 V 0/50-60 Hz
DC 176-280 V
DALI controllable
A basic isolation exists between power cable and control line
Safety class II
- Safety mark
- Conformity mark
Weight: 0.6 kg
This product contains light sources of energy efficiency class(es) E
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components. You can find them on our
website at www.bega.com.
Lamp
Module connected wattage 8.5 W
Luminaire connected wattage 10.4 W
Rated temperature ta=25 °C
Ambient temperature ta max=35 °C
50 714.4K27
Module designation LED-0923/927
Colour temperature 2700 K
Colour rendering index CRI >90
Module luminous flux 1155 lm
Luminaire luminous flux 581 lm
Luminaire luminous efficiency 55,9 lm/W
50 714.4K3
Module designation LED-0923/930
Colour temperature 3000 K
Colour rendering index CRI >90
Module luminous flux 1200 lm
Luminaire luminous flux 604 lm
Luminaire luminous efficiency 58,1 lm/W
Installation
****Luminaire housing must not be installed in heat-insulating material.
The recessed opening will be covered by the attachement of the installation
ring.
Fixing of the luminaire is achieved by using 2 adjustable claws.
LEDs are high-quality electronic components! Please avoid touching them
directly during installation or relamping.
Installation into false ceilings
A recessed opening of Ø 95 mm is necessary to accept the luminaire housing.
Free space depth min. 60 mm.
The claws catch the panel from the reverse side.
If minimum thickness of the panel is less than 3 mm it must be reinforced from
the reverse side. Maximum thickness of the panel must be no more than 20 mm.
The notch in the installation ring indicates the direction of maximum pivoting
range (35°) of the luminaire housing.
Remove glass with reflector from luminaire housing by turning counter-
clockwise.
The electrical connection must be made on site in the appropriate safety class
on the LED power supply unit connecting cable. A distribution box must be
used.
Ensure the correct assignment of the connecting cable. Establish the mains
connection on the brown (L) and blue (N) wires. The connection of the control
cables is achieved by means of the both leads marked with - DALI.
In case these leads are not used the luminaire will be operated at full light
output.
Push external LED-power supply unit and luminaire housing into ceiling cut-
out.
Luminaire housing and external LED-power supply unit must not be installed
in heat-insulating material.
Hand-tight screws of claw fasteners evenly. Insert glass with mounted
reflector by turning it clockwise into luminaire housing.
Make sure that gasket is positioned correctly. Mount ceiling frame ring
(magnetic) onto installation ring of the housing.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Defective glass must be replaced.
Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by
qualified persons using standard tools.
Disconnect from main supply.
Remove glass with reflector from housing by turning it counter-clockwise.
Pull ceiling frame ring off the installation ring of the pivoting housing.
Please follow the installation instructions for the LED module.
Check gasket. Screw in glass with mounted reflector by turning it clockwise
into luminaire housing.
Mount ceiling frame ring onto installation ring of the housing.
Defective glass must be replaced.
Spares
Spare glass 11 003 006 410 RG
LED power supply unit DEV-0434/250
LED module 2700 K LED-0923/927
LED module 3000 K LED-0923/930
Trim ring 72 009 804 L
Reflector 76 001 209
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>