BEGA 24 175 Ceiling and Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 24 175 Ceiling and Wall Luminaire
Dimension
Application
Unshielded ceiling and wall luminaire with high protection class
A luminaire made of aluminium alloy and crystal glass.
Product description
Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Crystal glass, white inside 2 mounting holes ø 4.5mm
Distance apart 236mm 2 screw cable glands with strain relief
for through-wiring power connecting cable ø 7–12mm
1 screw cable gland closed at the factory with a dummy plug
Connection terminal 2.5@
Earth conductor connection
LED power supply unit
220-240 V 0/50-60 Hz
DC 176-280 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Ballproof – The testing of ball impact safety was carried out exclusively with
handballs in accordance with DIN 18032-3: 2018-11.
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK10
Protection against mechanical impacts < 20 joule
– Safety mark
– Conformity mark
Weight: 2.5 kg
This product contains light sources of energy efficiency class(es) C, D
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components. You can find them on our website
at www.bega.com.
Lamp
Module connected wattage: 12.9 W
Luminaire connected wattage: 15 W
Rated temperature: ta=25 °C
Ambient temperature: ta max=30 °C
24 175K3
Module designation: LED-0985/830
Colour temperature: 3000 K
Colour rendering index: CRI >80
Module luminous flux: 2155 lm
Luminaire luminous flux: 1450 lm
Luminaire luminous efficiency: 96,7 lm/W
24 175K4
Module designation: LED-0985/840
Colour temperature: 4000 K
Colour rendering index: CRI >80
Module luminous flux: 2265 lm
Luminaire luminous flux: 1524 lm
Luminaire luminous efficiency: 101,6 lm/W
Installation
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo hexagon socket head screw (wrench size 3mm) through the opening in the
luminaire housing up to the stop and lift luminaire top. Disconnect the earth
conductor connection from the plug connection.
Disconnect plug-connection of the LED connecting cable.
Lead the mains supply cable through the screw cable gland into the luminaire
back housing.
The installed black gasket insert is intended for cables ø < 10mm.
For cables ø 10-12mm the enclosed grey gasket insert must be used.
In case of through-wiring replace the factory installed dummy plug with the
enclosed corresponding gasket insert.
At the same time, use the enclosed synthetic cone-thrust collar between gasket
insert and thrust screw (wrench size 22 mm) (see sketch).
Fix luminaire base with enclosed or any other suitable fixing material onto
the mounting surface.
Tighten screw cable gland.
Make the earth conductor connection and the electrical connection.
In order to guarantee the maximum service life of the electrical components,
the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the
position marked by the red information label immediately before finally
closing the luminaire.
Connect the LED connection cable by means of a plug connector. Make earth conductor connection between luminaire top and luminaire base. Push plug into coupler as far as it will go.
In order to ensure the tightness of the luminaire, the grub screw for fixing the luminaire upper part must not lie in the marked area.
Make sure that gasket is positioned correctly. Tighten grub screw firmly.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
Spare glass: 11 003 518
LED power supply unit:DEV-0150/350
LED module 3000 K: LED-0985/830
LED module 4000 K: LED-0985/840
Gasket glass: 83 001 907
Gasket housing: 83 002 167B1
Customer Support
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>