BEGA Wandleuchte Wall luminaire Applique24 374 Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
Wandleuchte Wall luminaire Applique24 374 Wall Luminaire
Instruction Manual
Instructions for use
Application
Wall luminaire with directed light.
Product description
Luminaire made of aluminium alloy, aluminium and stainless steel BEGA Unidure®
coating technology
Colour graphite or silver
Matt safety glass
Silicone gasket
2 mounting holes ø 5 mm
Distance apart 274 mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G
1.5@
Connection terminal 2.5
Earth conductor connection
LED power supply unit
220-240 V 0/50-60 Hz
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I
Ballproof – The testing of ball impact safety was carried out exclusively with
handballs in accordance with DIN 18032-3: 2018-11.
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK07
Protection against mechanical impacts < 2 joule
– Safety mark
****– Conformity mark
Weight: 1.6 kg
This product contains light sources of energy efficiency class(es) C
Dark Sky
The light from this luminaire is directed evenly and highly efficiently onto
the surface to be illuminated and emits less than 1 % of the luminaire
luminous flux into the upper halfspace of the luminaire.
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
Module connected wattage| 12 W
Luminaire connected wattage| 14.5 W
Rated temperature| ta = 25 °C
Ambient temperature| ta max = 50 °C
24 374 K3
Module designation| LED-0519/830
Colour temperature| 3000 K
Colour rendering index| CRI > 80
Module luminous flux| 2095 lm
Luminaire luminous flux| 1182 lm
Luminaire luminous efficiency| 81,5 lm / W
24 374 K4
Module designation| LED-0519/840
Colour temperature| 4000 K
Colour rendering index| CRI > 80
Module luminous flux| 2125 lm
Luminaire luminous flux| 1199 lm
Luminaire luminous efficiency| 82,7 lm / W
Installation
In outdoor areas, the light emission may only be directed downwards.
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Undo the screws and lift off the luminaire top.
Lead the mains supply cable through the cable entry into the luminaire
housing.
Fix luminaire base with enclosed or any other suitable fixing material onto
the mounting surface.
Be sure to use the gasket rings supplied.
Make earth conductor connection.
Push silicone sleeves over the lines and make electrical connection.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light
output.
In order to guarantee the maximum service life of the electrical components,
the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the
position marked by the red information label immediately before finally
closing the luminaire.
Make earth conductor connection between luminaire top and luminaire base.
Make sure that gasket is positioned correctlyReplace the luminaire top and
tighten the screws evenly.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation
instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
LED power supply unit| DEV-0484/700
LED module 3000 K| LED-0519/830
LED module 4000 K| LED-0519/840
Gasket| 83 001 843
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>