BEGA 33 639 Ceiling And Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 33 639 Ceiling And Wall Luminaire
Product Information
Safety
Product Usage Instructions
DIMENSION
Instructions for use
Safety
Overvoltage protection
Installation
Cleaning · Maintenance
Replacing the LED module
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 33 639 Ceiling And Wall Luminaire

Product Information

Product Name: Decken- und Wandleuchte Ceiling and wall luminaire Plafonnier et applique
Model Number: 33 639
IP Rating: IP 64
Application: Ceiling and wall luminaire made of aluminium and hand-blown satin matt three-ply opal glass. Suitable for a variety of interior and exterior lighting applications.

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning should only be carried out by a qualified electrician. The manufacturer does not accept liability for damage caused by improper use or installation. If any modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage Protection: The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. For additional protection against transients, it is recommended to use separate overvoltage protection components
available on our website at www.bega.com.

Lamp Specifications:

Module Connected Wattage: 22.2 W
Luminaire Connected Wattage: 25 W
Rated Temperature: ta max = 50°C
Ambient Temperature: ta = 25°C

LED Module Specifications (K3):

Module Designation: LED-0531/830
Colour Temperature: 3000 K
Colour Rendering Index (CRI): > 80
Module Luminous Flux: 3855 lm
Luminaire Luminous Flux: 2203 lm
Luminaire Luminous Efficiency: 88.1 lm / W

LED Module Specifications (K4):

Module Designation: LED-0531/840
Colour Temperature: 4000 K
Colour Rendering Index (CRI): > 80
Module Luminous Flux: 4055 lm
Luminaire Luminous Flux: 2317 lm
Luminaire Luminous Efficiency: 92.7 lm / W

Product Usage Instructions

LED are high-quality electronic components! During installation or relamping, avoid touching the light output opening of the LED directly.
To ensure maximum service life of the electrical components, place the enclosed desiccant pouch in the luminaire. Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label before closing the luminaire.
Connect the earth conductor plug connector of the LED device to the luminaire base. Firmly press plug parts (L,N) and (DA,DA) into the plug-in devices. Reassemble the LED unit and tighten fixing screws firmly and evenly. Take care not to damage the LED board mechanically.
Screw the glass clockwise into the luminaire base against the gasket. Ensure that the gasket is positioned correctly.

DIMENSION

BEGA 33 639 Ceiling And Wall Luminaire-FIG1

Instructions for use

Application
Ceiling and wall luminaire made of aluminium and hand-blown satin matt three- ply opal glass. For a variety of interior and exterior lighting applications.

Product description

Luminaire made of aluminium and stainless steel
BEGA Unidure® coating technology Opal glass, satin matt, with screw neck Silicone gasket
2 mounting holes ø 5.5 mm
Distance apart 280 mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G 1.5@ Connecting terminal and earth conductor terminal 2.5@ with plug connection
LED power supply unit 220-240 V x 0/50-60 Hz DC 170-276 V DALI-controllable
Basic insulation is provided between the mains and control cables BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 64
Dust-tight and protection against splash water Impact strength IK07
Protection against mechanical
impacts < 2 joule
r – Safety mark
c – Conformity mark
Weight: 3.7 kg
This product contains light sources of energy efficiency classes C, D

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

Module connected wattage 22.2 W
Luminaire connected wattage 25 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 50 °C

33 639 K3

Module designation LED-0531/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 3855 lm
Luminaire luminous flux 2203 lm
Luminaire luminous efficiency 88,1 lm / W

33 639 K4

Module designation LED-0531/840
Colour temperature 4000 K
Colour rendering index CRI > 80
Module luminous flux 4055 lm
Luminaire luminous flux 2317 lm
Luminaire luminous efficiency 92,7 lm / W

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo screws key slots and remove the LED-unit.
Pull off plug parts (L,N) and (DA,DA) on the plug-in device.
Pull off the earth conductor plug connector of the LED device in the luminaire base.
Lead the mains supply cable through the cable entry into the luminaire housing.
Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied. Make the earth conductor connection and the electrical connection.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.
Place the earth conductor plug connector of the LED device in the luminaire base.
Press plug parts (L,N) and (DA,DA) firmly into the plug-in devices.
Reassemble LED-unit and tighten fixing screws firmly and evenly. Please observe that the LED board is not damaged mechanically.
Screw glass clockwise into the luminaire base against the gasket .
Make sure that gasket is positioned correctly.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced..
Close the luminaire.

Spares