BEGA 24135 Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
Technical amendments reserved
24 135
Wall luminaire
Instruction Manual
24135 Wall Luminaire
Instructions for use
Application
Wall luminaire with two-sided light distribution opening.
Fully glare free light for lighting wall surfaces.
For interior or exterior lighting design.
Product description
Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Clear safety glass
Silicone gasket
Reflector made of pure anodised aluminium
Mounting plate with 4 mounting holes ø 4.5 mm
Distance apart 86 x 86 mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G
1.5◽
Connecting terminal 2.5◽ with plug connection
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit 220-240 V ≂ 0/50-60 Hz
DC 176-264 V
DALI-controllable
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK04
Protection against mechanical impacts < 0.5 joule
– Safety mark
****– Conformity mark
Weight: 3.0 kg
This product contains light sources of energy efficiency classes D
Lamp
| Module connected wattage | 32.8 W |
|---|---|
| Luminaire connected wattage | 36.7 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 50 °C |
24 135 K3
| Module designation | 2x LED-0945/830 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 80 |
| Module luminous flux | 5540 lm |
| Luminaire luminous flux | 1853 lm |
| Luminaire luminous efficiency | 50,5 lm / W |
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Installation
Undo hexagon socket head screw (wrench size 3 mm) through the opening in the
luminaire housing up to the stop and lift luminaire top.
Lead the mains supply cable through the cable entry of the luminaire base.
Fix luminaire base with enclosed fixing screws diagonally on the mounting
surface. Make sure that the mounting screw of the luminaire housing is not
located above one of the mounting brackets on the mounting plate.
Make earth conductor connection. Push silicone sleeves over the lines and make
electrical connection. For digital control please use the connecting terminal
DA, DA.
In case this terminal is not used the luminaire will be operated at full light
output.
In order to guarantee the maximum service life of the electrical components,
the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the
position marked by the red information label immediately before finally
closing the luminaire.
Push plug into coupler as far as it will go.
Make sure that gasket is positioned correctly.
Install the luminaire top, press-on and tighten screw.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
| LED power supply unit | DEV-0270/700 |
|---|---|
| LED module 3000 K | LED-0945/830 |
| LED module 4000 K | LED-0945/840 |
| Reflector | 76 001 850 |
| Gasket wall box | 83 001 857 |
BEGA Gantenbrink-Leuchten KG · Postfach 31 60
· 58689 Menden
· info@bega.com
· www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>