BEGA 33360 LED Wall Washer Instruction Manual

BEGA 33360 LED Wall Washer

Product Information

are
protected against overvoltage in accordance with DIN EN 61547. For
additional protection against transients, it is recommended to use
separate overvoltage protection components. These can be found on
our website at www.bega.com.
Safety| The installation and operation of this luminaire must comply
with national safety regulations. Only a qualified electrician
should carry out the installation and commissioning. The
manufacturer is not liable for any damage caused by improper use or
installation. If modifications are made to the luminaire, the
person responsible for these modifications will be considered the
manufacturer.
Lamp Module connected wattage| 16.2W
Luminaire connected wattage| 19W
Rated temperature| Ambient temperature: 25-35°C
LED-0590/830| Module designation: 33 360 K3
Color temperature: 3000 K
Color rendering index: CRI > 80
Module luminous flux: 2795 lm
Luminaire luminous flux: 2106 lm
Luminaire luminous efficiency: 110.8 lm/W
LED-0590/840| Module designation: 33 360 K4
Color temperature: 4000 K
Color rendering index: CRI > 80
Module luminous flux: 2835 lm
Luminaire luminous flux: 2136 lm
Luminaire luminous efficiency: 112.4 lm/W

Product Usage Instructions

1. During installation or relamping, avoid touching the light output opening of the LED directly.
2. To ensure the maximum service life of the electrical components, place the enclosed desiccant pouch in the luminaire. Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label before finally closing the luminary.
3. Make an earth conductor connection between the luminaire top and the luminaire base. Ensure that the gasket is positioned correctly.
4. Install the luminaire top, press on, and tighten the screws evenly.

Spares

Application

• Wall washer with symmetrical light distribution for the illumination of façades and wall surfaces with the mounting surface being the reflection surface.
• The luminaire can be installed with the light distribution opening upwards or downwards.

Product Description

• Luminaire made of aluminum alloy, aluminum and stainless steel
• BEGA Unidure® coating technology
• Clear safety glass
• Silicone gasket
• Reflector made of pure anodized aluminium 2 mounting holes ø 4.5 mm
• Distance apart 190 mm 2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G 1.5@
• Connection terminal 2.5@
• Earth conductor connection 2-pole connecting terminal for digital control
• LED power supply unit 220-240 V x 0/50-60 Hz
• DC 176-280 V
• DALI-controllable
• Basic insulation is provided between the mains and control cables
• BEGA Thermal Control®
• Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
• Safety class I
• Protection class IP 65
• Dust-tight and protection against water jets
• Impact strength IK07
• Protection against mechanical impacts < 2 joule
  • Safety mark
  • Conformity mark
• Weight: 1.6 kg
• This product contains light sources of energy efficiency classes C, D

Overvoltage protection

• The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
• To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
• You can find them on our website at www.bega.com.

Safety

• The installation and operation of this luminaire are subject to national safety regulations.
• Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation.
• If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp Specification

• Module connected wattage 16.2 W
• Luminaire connected wattage 19 W
• Rated temperature ta = 25 °C
• Ambient temperature ta max = 35 °C

33 360 K3

• Module designation LED-0590/830
• Colour temperature 3000 K
• Colour rendering index CRI > 80
• Module luminous flux 2795 lm
• Luminaire luminous flux 2106 lm
• Luminaire luminous efficiency 110,8 lm / W

33 360 K4

• Module designation LED-0590/840
• Colour temperature 4000 K
• Colour rendering index CRI > 80
• Module luminous flux 2835 lm
• Luminaire luminous flux 2136 lm
• Luminaire luminous efficiency 112,4 lm / W

Installation

• LED are high-quality electronic components!
• Please avoid touching the light output opening of the LED directly during installation or relamping.
• Undo hexagon socket head screws (wrench size 3 mm) through the opening in the luminaire housing up to the stop and lift luminaire top.
• Lead the mains supply cable through the cable entry of the luminaire base.
• Ensure correct directionality towards the area to be illuminated.
• Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
• Make the earth conductor connection and the electrical connection.
• For digital control please use the connecting terminal DA, DA.
• In case this terminal is not used the luminaire will be operated at full light output.
• In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
• Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.
• Make earth conductor connection between luminaire top and luminaire base.
• Make sure that gasket is positioned correctly.
• Install the luminaire top, press-on and tighten screws evenly.

Dimension

Cleaning And Maintenance

• Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
• Do not use high-pressure cleaners.

Replacing the LED module

• The designation of the LED module is noted on a label in the luminaire.
• The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
• The module can be replaced by qualified persons using standard tools.
• Disconnect the system and open the luminaire.
• Please follow the installation instructions for the LED module.
• Inspect and, if necessary, replace the luminaire gaskets.
• The defective glass must be replaced.
• Close the luminaire.

Spares

• LED power supply unit DEV-0409/700
• LED module 3000 K LED-0590/830
• LED module 4000 K LED-0590/840
• Reflector 76 001 421
• Gasket 83 001 380

BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com.

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>