BEGA 50163.1 LED Ceiling Mounted Downlight Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50163.1 LED Ceiling Mounted Downlight Instruction Manual
Instructions for use
Application
Compact downlight · indoor luminaire with symmetrical narrow beam light
distribution
Product description
- Die-cast aluminium and aluminium housing, finish Colour white
- Safety glass with optical structure
- Silicone gasket
- Reflector surface made of pure aluminium 2 mounting holes ø 4.8mm
- Distance apart 70mm 1 cable entry for mains supply cable up to ø 10,5mm
- Connection terminal 2.5@
- Earth conductor connection
- BEGA Ultimate Driver®
- LED power supply unit 220-240 V x 0/50-60 Hz
- DC 176-264 V
- Safety class I
- Protection class IP 65
- Dust-tight and protection against water jets
- Impact strength IK06
- Protection against mechanical impacts < 1 joule
- Safety mark
- Conformity mark
- Weight: 0.85 kg
- This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e.g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at
www.bega.com.
Lamp
Module connected wattage 8.2 W
Luminaire connected wattage 9.5 W
Rated temperature ta=25 °C
Ambient temperature ta max=40 °C
50 163.1K3
Module designation LED-0588/930
Colour temperature 3000 K
Colour rendering index CRI >90
Module luminous flux 1205 lm
Luminaire luminous flux 661 lm
Luminaire luminous efficiency 69,6 lm/W
50 163.1K4
Module designation LED-0588/940
Colour temperature 4000 K
Colour rendering index CRI >90
Module luminous flux 1255 lm
Luminaire luminous flux 689 lm
Luminaire luminous efficiency 72,5 lm/W
Lighting technology
Half beam angle 25
Installation
Undo the screws and lift off the luminaire top. LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Lead the mains supply cable through the cable entry into the luminaire back housing. Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface. Be sure to use the gasket rings supplied. Make earth conductor connection. Push silicone sleeves over the lines and make electrical connection. Make earth conductor connection between luminaire top and luminaire base. Push plug into coupler as far as it will go. Install the luminaire top, press-on and tighten screws evenly
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
- The designation of the LED module is noted on a label in the luminaire.
- The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
- The module can be replaced by qualified persons using standard tools.
- Disconnect the system and open the luminaire.
- Please follow the installation instructions for the
- LED module.
- Inspect and, if necessary, replace the luminaire gaskets.
- Defective glass must be replaced.
- Close the luminaire.
Spares
LED power supply unit DEV-0304/350
LED module 3000 K LED-0588/930
LED module 4000 K LED-0588/940
Reflector 76 001 426
Gasket 83 001 570
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden ·
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>