BEGA 50 495 Ceiling and Wall Luminaire for Indoor Use Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50 495 Ceiling and Wall Luminaire for Indoor
Product Information
Product Description| Luminaire made of aluminium alloy and stainless steel,
finish
Colour white Hand-blown opal glass, satin matt
---|---
Distance Apart| 142 mm
Earth Conductor Connection| Yes
Dimming Compatibility| Phase angle or phase section dimming at 220-230 V and
50/60
Hz
Safety Class| Class I
Protection Class| IP 44 (Protected against granular foreign bodies up to 1 mm
and
splash water)
Impact Strength| IK02
Weight| 2.5 kg
Light Source Energy Efficiency Class| G
Product Usage Instructions
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
The electronic components installed in the luminaire areprotected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against transients and other risks, we recommend using separate overvoltage protection components. You can find them on our website at www.bega.com.
Dimension
Instructions for use
Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass,
satin matt and aluminium alloy housing, for all lighting tasks. They are ideal
for places where a soft anduniform lighting distribution is required.
Luminaire with a high protection class.
Product description
Luminaire made of aluminium alloy and stainless steel, finish Colour white
Hand-blown opal glass, satin matt 2 mounting holes ø 5 mm Distance apart 142
mm 1 cable entry for mains supply cable up to ø 10,5 mm Connection terminal
2.5@Earth conductor connection LED module for power supply Suitable for phase
angle or phase section dimming 220-230 V y 50/60 Hz Safety class I Protection
class IP 44 Protected against granular foreign bodies ≥ 1 mm and splash water
Impact strength IK02 Protection against mechanical impacts < 0.2 joule r –
Safety mark c – Conformity mark Weight: 2.5 kg This product contains
light sources of energy efficiency class(es) G
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e. g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at www.bega.com.
- Lamp
- Module connected wattage
- Luminaire connected wattage 7.4 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 35 °C
- 50 495 K27
- Module designation LED-1250/927
- Colour temperature 2700 K
- Colour rendering index CRI > 90
- Module luminous flux 660 lm
- Luminaire luminous flux 485 lm
- Luminaire luminous efficiency 65,5 lm / W
- 50 495 K3
- Module designation LED-1250/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 660 lm
- Luminaire luminous flux 485 lm
- Luminaire luminous efficiency 65,5 lm / W
Installation
Lead the mains supply cable through the cable entry into the luminaire back
housing. Fix luminaire base with enclosed or any other suitable fixing
material onto the mounting surface. Be sure to use the gasket rings supplied.
Make earth conductor connection. Push silicone sleeves over the lines and make
electrical connection. Snap the opal glass into the lower spring clips,
centralise and push into the upper spring clips.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by a qualified electrician or a comparably qualified person using standard tools. Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module. Defective glass must be replaced. Close the luminaire.
- Spares
- Spare glass 11 002 363 .0R G
- LED module 2700 K LED-1250/927
- LED module 3000 K LED-1250/930
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com