BEGA 50594.1 LED Wall Washer Instruction Manual

BEGA 50594.1 LED Wall Washer

Product Information

• Safety: The installation and operation of this luminaire should be done in accordance with national safety regulations. Only a qualified electrician should carry out the installation and commissioning. The manufacturer is not liable for any damage caused by improper use or installation. Any modifications made to the luminaire should be done by the person responsible for these modifications and they will be considered the manufacturer.
• Overvoltage Protection: The electronic components installed in the luminaire are protected against overvoltage according to DIN EN 61547. For additional protection against transients, it is recommended to use separate overvoltage protection components available on the manufacturer’s website.
• Lamp Module Connected Wattage: 24.6 W
• Luminaire Connected Wattage: 28.1 W
• Rated Temperature: 25°C
• Ambient Temperature: 25°C
• Module Designation: 50 594.1 K3
• Colour Temperature: 3000 K
• Colour Rendering Index (CRI): CRI > 90
• Module Luminous Flux: 3620 lm
• Luminaire Luminous Flux: 2571 lm
• Luminaire Luminous Efficiency: 91.5 lm/W

Product Usage Instructions

1. Ensure that the installation and operation of the luminaire are carried out in accordance with national safety regulations.
2. Only a qualified electrician should perform the installation and commissioning.
3. Do not use or install the luminaire improperly to avoid any potential damage.
4. If any modifications are made to the luminaire, they should be done by the person responsible for these modifications.
5. For additional protection against transients, it is recommended to use separate overvoltage protection components available on the manufacturer’s website.
6. The lamp module connected wattage is 24.6 W and the luminaire connected wattage is 28.1 W.
7. The rated temperature and ambient temperature should not exceed 25°C.
8. The module designation is 50 594.1 K3 with a colour temperature of 3000 K.
9. The colour rendering index (CRI) is greater than 90, indicating high-quality colour reproduction.
10. The module luminous flux is 3620 lm, while the luminaire luminous flux is 2571 lm.
11. The luminaire luminous efficiency is 91.5 lm/W, indicating energy-efficient performance.

Dimension

Wall washer for indoor use

Application

Wall washer · indoor luminaire for the glare free illumination of wall surfaces with the mounting surface being the reflection surface. The light emits upwards and downwards.

Product description

• Die-cast aluminium and aluminium housing, finish Colour velvet white
• Crystal glass, inside matt
• Reflector made of pure anodised aluminium 2 mounting holes ø 4.8 mm
• Distance apart 200 mm
• 2 cable entries for through-wiring for mains cable up to ø 8 mm max. 3 × 1.5@
• Connection terminal 2.5@
• Earth conductor connection
• LED power supply unit
• 220-240 V x 0/50-60 Hz
• DC 176-276 V
• BEGA Thermal Switch®
• Temporary thermal shutdown to protect temperature-sensitive components
• Safety class I
• Impact strength IK07
• Protection against mechanical
• impacts < 2 joule
• – Safety mark
• – Conformity mark
• Weight: 1.9 kg
• This product contains light sources of energy efficiency class(es) D

Safety

• The installation and operation of this luminaire are subject to national safety regulations.
• Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation.
• If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

• The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
• To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
• You can find them on our website at www.bega.com.

Lamp

• Module connected wattage 24.6 W

• Luminaire connected wattage 28.1 W

• Rated temperature ta = 25 °C

• Ambient temperature ta max = 25 °C
  50 594.1 K3

• Module designation 2x LED-0696/930

• Colour temperature 3000 K

• Colour rendering index CRI > 90

• Module luminous flux 3620 lm

• Luminaire luminous flux 2571 lm

• Luminaire luminous efficiency 91,5 lm / W
  50 594.1 K4

• Module designation 2x LED-0696/940

• Colour temperature 4000 K

• Colour rendering index CRI > 90

• Module luminous flux 3770 lm

• Luminaire luminous flux 2678 lm

• Luminaire luminous efficiency 95,3 lm / W

Installation

• LED are high-quality electronic components!
• Please avoid touching the light output opening of the LED directly during installation or relamping.
• Undo screws and lift off luminaire top.
• Loosen earth connection (plug connection) and LED-connection between luminaire top and luminaire base.
• Lead the mains supply cable through the cable entry of the luminaire base.
• Note position of application of the luminaire “arrow down”.
• Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
• Be sure to use the gasket rings supplied.
• Make earth conductor connection.
• Push silicone sleeves over the lines and make electrical connection.
• Make earth connection (plug connection) and
• LED-connection between luminaire top and luminaire base again.
• Install luminaire top part, adjust it and tighten screws evenly.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

• The designation of the LED module is noted on a label in the luminaire.
• The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The replacement can be carried out by a qualified person using standard tools.
• Disconnect the system and open the luminaire.
• Uninstall the reflector.
• Please follow the installation instructions for the LED module.
• Install the reflector. Defective glass must be replaced. Close the luminaire.

Replacement of the glass

• Undo screws and lift off luminaire top.
• Loosen earth connection (plug connection) and LED-connection between luminaire top and luminaire base.
• Loosen reflector screws, separate earth connection and remove reflector.
• Loosen screws of the glass retaining springs and remove glass retaining springs from the luminaire top.
• Remove damaged glass. Insert replacement glass.
• Reinstall glass retaining springs and tighten screws on both sides.
• Insert reflector into luminaire top part, make earth connection to reflector and tighten reflector screws (0,6 Nm).
• Make earth connection (plug connection) and LED-connection between luminaire top and luminaire base again.
• Install luminaire top part, adjust it and tighten screws evenly.

Spares

• Spare glass 14 001 183 RG
• LED power supply unit DEV-0194/700
• LED module 3000 K LED-0696/930
• LED module 4000 K LED-0696/940
• Reflector 76 001 510

BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>