BEGA 50 301 Ceiling and Wall Luminaire for Indoor Use Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50 301 Ceiling and Wall Luminaire for Indoor
Product Information
The product is a luminaire that requires installation and operation in accordance with national safety regulations. It should only be installed and commissioned by a qualified electrician. The manufacturer does not accept liability for damage caused by improper use or installation. The luminaire is equipped with electronic components that are protected against overvoltage in accordance with DIN EN 61547. Additional overvoltage protection components are recommended for further protection against transients, which can be found on the manufacturer’s website at www.bega.com.
Lamp Information
- Model: 50 301
- Colour Temperature: 2700 K / 3000 K
- Colour Rendering Index (CRI): > 90
- Module Luminous Flux: 1770 lm / 1795 lm
- Luminaire Luminous Flux: 1311 lm / 1329 lm
- Luminaire Luminous Efficiency: 89.2 lm/W / 90.4 lm/W
Installation Precautions
Prior to installation, the luminaire housing must be inserted into the trim frame (accessory) and then mounted onto the mounting surface. Ensure that the openings in the trim frame align with the grub screws of the luminaire housing.
Installation Instructions
- Avoid touching the light output opening of the LED directly during installation or relamping.
- Lead the mains supply cable through the cable entry into the luminaire housing.
- Securely fix the luminaire housing onto the mounting surface using enclosed or suitable fixing material.
- Use the enclosed gaskets for proper installation.
- Make earth and electrical connection to the terminal.
- Position the glass over the luminaire housing, aligning the retaining springs with the recesses in the raised edge of the glass.
- Press the glass against the retaining springs at a flat angle and push it into the luminaire housing until it is securely fixed through the three lobes on the opposite side.
- If installing on the ceiling, screw the two grub screws (Allen screws) with gentle pressure against the retaining springs to securely hold the glass in place and make it resistant to vibration.
Dimension
Instructions for use
Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass
and metal housing, for all lighting tasks. They are ideal for places where a
soft and uniform lighting distribution is required.
Product description
Metal housing, finish Colour white Hand-blown opal glass, satin matt 2
mounting holes ø 6 mm Distance apart 180 mm 2 cable entries for through-wiring
for mains cable up to ø 10.5 mm max. 3 × 1.5@ Connection terminal 2.5@ Earth
conductor connection LED power supply unit 220-240 V y 50-60 Hz BEGA Thermal
Switch® Temporary thermal shutdown to protect temperature-sensitive components
Safety class IImpact strength IK05 Protection against mechanical impacts <
0.7-joule r – Safety mark c – Conformity mark This product contains light
sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e. g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at
www.bega.com.
- Lamp
- Module connected wattage 11 W
- Luminaire connected wattage 14.7 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 45 °C
- 50 301 K27
- Colour temperature 2700 K
- Colour rendering index CRI > 90
- Module luminous flux 1770 lm
- Luminaire luminous flux 1311 lm
- Luminaire luminous efficiency 89,2 lm / W
- 50 301 K3
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 1795 lm
- Luminaire luminous flux 1329 lm
- Luminaire luminous efficiency 90,4 lm / W
Notice prior to installation: Luminaire with trim frame The luminaire
housing must be inserted in the trim frame (accessory) before it is mounted
onto the mounting surface.Make sure that the two openings in the trim frame
coincide with the positions of the grub screws of the luminaire housing.
Installation
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping. Lead
mains supply cable through the cable entry into the luminaire housing. Fix the
luminaire housing with enclosed or any other suitable fixing material onto the
mounting surface. It is imperative to use the enclosed gaskets. Make earth and
electrical connections to the terminal.
Position the glass over the luminaire housing so that the retaining
springs fit into the two recesses in the raised edge of the glass. Press the
glass against the retaining springs ata flat angle as far as it will go and
push it into the luminaire housing (see drawing). Gentle pressure on the glass
will fix it in the luminaire housing through the three lobes on the opposite
side.
IMPORTANT:
If the luminaire is to be installed on the ceiling, it is essential that the
two grub screws (Allen screws) should be screwed with gentle pressure against
the retaining springs. In this way, the glass is held securely in place and is
resistant to vibration.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Opening the luminaire
Unscrew the two grub screws (Allen screws) of the luminaire housing as far as
they will go. A recess (identifiable by touch) in the edge of the glass
indicates the direction from which the luminaire glass must be pressed against
the spring pressure of the glass retaining springs in order to release it from
the luminaire housing. Pull the glass away from the luminaire housing against
the holding force of the retaining springs and remove it.
Replacement of the LED unit
The designation of the LED unit is noted on a label in the luminaire. The
light colour and light output of BEGAreplacement units correspond to those of
the LED units originally fitted. The LED unit can be replaced by qualified
persons using standard tools. Disconnect the system and open the luminaire.
Replace the LED unit. Close the luminaire. A damaged glass must be replaced.
Accessory · Trim frames
For this luminaire metal trim frames in 3 enamel surfaces are optionally
available. Trim frames are accessories and must be ordered separately.
- Colour white 13 134
- Colour palladium 13 135
- Colour glossy silver 13 136
- Spares
- Spare glass 11 003 243 .0R G
- LED unit 2700 K 75 002 256 K27
- LED unit 3000 K 75 002 256 K3
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>