BEGA 23 233.1 Wall Luminaire for Indoor Use Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 23 233.1 Wall Luminaire for Indoor Use
Product Information
Product Usage Instructions
Application
Product Description
Lamp Specification
Safety
Overvoltage protection
Installation
Dimension
Relamping And Maintenance
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 23 233.1 Wall Luminaire for Indoor Use

BEGA-23 233.1-Wall-Luminaire-for-Indoor-Use-PRODUCT

Product Information

Lamp Module connected wattage: 7.8 W
Luminaire connected wattage: 10 W
Rated temperature: 25 – 50 °C
Ambient temperature: 23 – 233.1 °C
Module designation: 2x LED-0273/930
Colour temperature: 3000 K
Colour rendering index (CRI): > 90
Module luminous flux: 1240 lm
Luminaire luminous flux: 838 lm
Luminaire luminous efficiency: 83.8 lm/W

Product Usage Instructions

Safety:

The installation and operation of this luminaire must comply with national safety regulations.
Installation and commissioning should only be done by a qualified electrician.
The manufacturer is not liable for damage caused by improper use or installation.
Any modifications made to the luminaire should be performed by a responsible person who will be considered the manufacturer.
To achieve additional protection against overvoltage and transients, separate overvoltage protection components are recommended. They can be found on the manufacturer’s website at www.bega.com.
If the luminaire is mounted on a metallic, electroconductive surface, ensure that the mounting surface is connected conductively to the earth conductor of the luminaire.

Installation:

LED components are sensitive, avoid touching the light output opening of the LED directly during installation or relamping.
To open the luminaire, loosen the lateral knob and remove the cap. Take out the glass component and loosen the isolating plug (LED lines).
Pull silicone sleeves over the wires, make an earth connection and electrical connection to the terminal.
Mount the luminaire housing with suitable fixing material onto the mounting surface.
Reconnect the isolating plug (LED-lines) and lead the lines back through the cable routing to avoid damaging them by the rotating mechanism.
Place the glass into the luminaire housing, close the luminaire with the cap, and screw in the knob into the cap.

Maintenance:

To disassemble the LED module, remove the glass component and loosen the isolating plug (LED lines).
Replace any broken glass.
Clean the glass and luminaire regularly with solvent-free cleansers to remove dirt.
When assembling the LED replacement module, insert the glass component into the light shade and remount the Teflon ring. Reconnect the isolating plug (LED lines) and lead the lines through the cable routing.

Application

Wall luminaire · indoor luminaire made of handblown opal glass, with metal housing.
The light aperture can be adjusted infinitely by rotating the shield around its longitudinal axis.
Light aperture 170°; adjustable 300°.

Product Description

Luminaire made of Aluminium, finish Colour white
Hand-blown opal glass 2 elongated fixing holes
Width 6 mm · 360 mm spacing
Built-in toggle switch
Connection terminal 2.5@
Earth conductor connection
LED power supply unit 220-240 V x 0/50-60 Hz
DC 170-280 V
Safety class I
- Safety mark
- Conformity mark
Weight: 1.1 kg
This product contains light sources of energy efficiency class(es) D

Lamp Specification

Module connected wattage 7.8 W
Luminaire connected wattage 10 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 50 °C

23 233.1 K3

Module designation 2x LED-0273/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 1240 lm
Luminaire luminous flux 838 lm
Luminaire luminous efficiency 83,8 lm / W

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Please note:
If the luminaire is to be mounted onto a metallic, electroconductive surface, it is mandatory to make sure that the mounting surface is connected conductively to the earth conductor of the luminaire!

Installation

LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.

To open the luminaire:

Loosen the lateral knob and remove the cap. Take out the glass component and loosen the isolating plug (LED-lines).
Pull silicone sleeves over the wires, and make an earth connection and electrical connection to the terminal.
Mount luminaire housing with suitable fixing material onto the mounting surface.
Take the glass component and reconnect the isolating plug (LED lines).
It is imperative to lead the lines back through the cable routing to avoid damaging lines by the rotating mechanism.
Place glass into the luminaire housing, close the luminaire with the cap and screw in the knob into the cap.

Dimension

BEGA-23 233.1-Wall-Luminaire-for-Indoor-Use-FIG-1

Relamping And Maintenance

Disconnect from main supply.
Loosen lateral knob and remove cap. Take out glass component and loosen the isolating plug (LED-lines).
Remove the teflon ring at the opening side of the light shade.
Clean glass and luminaire regularly with solvent-free cleansers from dirt.
Disassemble LED module.
Assemble LED replacement module.
Insert glass component into the light shade and remount the teflon ring.
Take the glass component and reconnect the isolating plug (LED-lines).
It is imperative to lead the lines through the cable routeing to avoid demaging of lines by the rotating mechanism.
Place glass into luminaire housing, close luminaire with the cap and screw in knob into the cap.
A broken glass must be replaced.