BEGA 51 261.5 Wall Luminaire Instruction Manual

BEGA 51 261.5 Wall Luminaire

Product Information

• Product Name: LED Luminaire
• Manufacturer: Unknown
• Model Number: Unknown
• Safety: The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should carry out the installation and commissioning. The manufacturer is not liable for damage caused by improper use or installation. Any modifications made to the luminaire should be done by a responsible person who will assume the role of the manufacturer.
• Overvoltage Protection: The electronic components in the luminaire are protected against overvoltage according to DIN EN 61547. For additional protection against transients and other factors, separate overvoltage protection components are recommended. These components can be found on the manufacturer’s website at www.bega.com.
• Lamp Module Connected Wattage: 27 W
• Luminaire Connected Wattage: 31 W
• Rated Temperature: ta = 25°C to ta = 45°C
• Ambient Temperature: ta = 25°C to ta = 45°C
• Module Designation: 2x LED-1319/930
• Colour Temperature: 3000 K
• Colour Rendering Index (CRI): CRI > 90
• Module Luminous Flux: 4200 lm
• Luminaire Luminous Flux: 1762 lm
• Luminaire Luminous Efficiency: 56.8 lm/W
• Spare P ar t s : DEV-0388/700i LED power supply unit, LED-1319/930 LED module 3000 K with diffusor

Product Usage Instructions

1. Safety: Before proceeding with installation or operation, ensure that you comply with national safety regulations. It is recommended to hire a qualified electrician to handle the installation and commissioning process. The manufacturer will not be held responsible for any damage resulting from improper use or installation.
2. Overvoltage Protection: The luminaire’s electronic components are protected against overvoltage according to DIN EN 61547. To enhance protection against transients and other factors, it is advised to use separate overvoltage protection components. These components can be found on the manufacturer’s website at www.bega.com.
3. Lamp Module Connected Wattage: The connected wattage of the lamp module is 27 W.
4. Luminaire Connected Wattage: The connected wattage of the luminaire is 31 W.
5. Rated Temperature: The luminaire can operate within a rated temperature range of ta = 25°C to ta = 45°C.
6. Ambient Temperature: The luminaire can operate within an ambient temperature range of ta = 25°C to ta = 45°C.
7. Module Designation: The luminaire uses a 2x LED-1319/930 module.
8. Colour Temperature: The luminaire emits light with a colour temperature of 3000 K.
9. Colour Rendering Index (CRI): The CRI of the luminaire is greater than 90, indicating high-quality colour rendering.
10. Module Luminous Flux: The module produces a luminous flux of 4200 lm.
11. Luminaire Luminous Flux: The luminaire emits a luminous flux of 1762 lm.
12. Luminaire Luminous Efficiency: The luminous efficiency of the luminaire is 56.8 lm/W.
13. Spare Parts: In case of replacement needs, the recommended spare parts are DEV-0388/700i LED power supply unit and LED-1319/930 LED module with diffusor.
    Note: When installing or replacing the LED, avoid touching the light output opening directly to prevent any damage to the LED.

Application

• Wall luminaire · indoor luminaire with light emission on two sides for the glare free illumination of wall surfaces with the mounting surface being the reflection surface.
• A luminaire which allows interesting illumination concepts individually or in rows.

Product description

• Luminaire housing made of aluminium, finish Colour velvet black
• Silicone light diffuser
• 3 elongated fixing holes
• Width 4.5 mm · 340 mm spacing
• Mounting plate with several openings for cable entry and through-wiring for mains cable Connecting terminals 2.5@
• Earth conductor connection
• LED power supply unit
• 220-240 V x 0/50-60 Hz
• DC 176-264 V
• DALI-controllable
• Number of DALI addresses: 1
• Basic insulation is provided between the mains and control cables
• BEGA Thermal Control®
• Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
• Safety class I
• c  – Conformity mark
• Weight: 2.9 kg
• This product contains light sources of energy efficiency class(es) D

Safety

• The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
• The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

• The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
• To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
• You can find them on our website at www.bega.com.

PRODUCT SPECIFICATION

• Lamp
  • Module connected wattage 27 W
  • Luminaire connected wattage 31 W
  • Rated temperature ta = 25 °C
  • Ambient temperature ta max = 45 °C
• 51 261.5 K3
  • Module designation 2x LED-1319/930
  • Colour temperature 3000 K
  • Colour rendering index CRI > 90
  • Module luminous flux 4200 lm
  • Luminaire luminous flux 1762 lm
  • Luminaire luminous efficiency 56,8 lm / W

Installation

• LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

• Undo the hexagon socket head screws
  (wrench size 3 mm) and lift luminaire housing. Loosen earth connection (plug connection) between luminaire housing and mounting plate. Pass the power connecting cable through one of the openings of the mounting plate.

• Fasten the mounting plate with the supplied fastening material or other suitable fastening material to the installation surface.
  Note position of application of the mounting plate “arrow down”.

• Make the electrical connection to the terminals. Please ensure correct wire assignment for the connecting cable.

• Connect the earth conductor to the green-yellow wire (1). Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N).

• Use the terminals marked DA, DA for digital control.

• If these terminals are not used, the luminaire will operate at full light output.

• Make earth connection (plug connection) between luminaire housing and mounting plate again.

• Hang the luminaire housing in the mounting plate and screw it in place with the hexagon socket head screws.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

• The designation of the LED module is noted on a label in the luminaire.
• The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
• Disconnect the system from the power supply. Press the synthetic LED cover together lengthwise and remove it from the housing profile.
• Remove the LED module. Install the replacement LED module.
• Please follow the installation instructions for the LED module.
• A defective LED cover must be replaced.

Spares

• LED power supply unit DEV-0388/700i
• LED module 3000 K with diffusor LED-1319/930

ABOUT COMPANY

• BEGA Gantenbrink-Leuchten KG
• Postfach 31 60
• 58689 Menden
• info@bega.com
• www.bega.com

References

• BEGA · Das gute Licht.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>