BEGA 50252.6 Studio Line Recessed Ceiling Light LED Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
50252.6 Studio Line Recessed Ceiling Light LED
Product Information
| Component | Description |
|---|---|
| Safety | The installation and operation of this luminaire are subject to |
national safety regulations. Installation and commissioning may
only be carried out by a qualified electrician. The manufacturer
accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the
luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection| The electronic components installed in the luminaire
are
protected against overvoltage in accordance with DIN EN 61547. To
achieve additional protection against e.g. transients, etc. we
recommend separate overvoltage protection components. You can find
them on our website at www.bega.com.
The lamp Module connected wattage| 12.3 W
Luminaire connected wattage| 14.3 W
Rated temperature| 25-40°C
Ambient temperature| ta, ta max
Module designation| LED-0423/930 3000 K
Color temperature| 3000 K
Color rendering index| CRI > 90
Module luminous flux| 1640 lm
Luminaire luminous flux| 706 lm
Luminaire luminous efficiency| 49.4 lm / W
Product Usage Instructions
- The recessed opening will be covered by the frame of the luminaire.
- Fix the luminaire using the 2 adjustable wedge-shaped claws.
- Avoid touching the LEDs directly during installation or relamping.
- Refer to the operating instructions of the LED power supply units.
- Push the external LED power supply unit and luminaire into the ceiling cut-out.
- Tighten the screws of the claw fasteners evenly by hand.
- Center the reflector onto the enclosed housing shield.
- Mount the housing shield with a reflector onto the luminaire frame (magnetic) (see sketch).
- The power supply units are only suitable for the operation of one LED luminaire.
- For accessories, a separate instructions for use can be provided upon request.
Recessed ceiling downlight for indoor use
Dimension
Instructions for use
Application
- Recessed ceiling luminaire · indoor luminaire with aluminum housing for shielded light deflected downwards.
- Luminaire for connection to external LED power supply unit
Product Description
- Recessed LED ceiling luminaire »STUDIO LINE« made of die-cast aluminium without a power supply unit
- Aluminum housing shield,
- Finish Colour velvet black inside hue matt copper
- Light-diffusing silicone lens
- A reflector of anodised pure aluminum
- Fixing is achieved by using 2 adjustable wedge-shaped claws
- 1 connecting cable with strain relief and plug connector system for the BEGA power supply unit, on/off or DALI
- Safety Class III 3
- c – Conformity mark
- Weight: 0.4 kg
- This product contains light sources of energy efficiency class(es) E
Safety
- The installation and operation of this luminaire are subject to national safety regulations.
- Installation and commissioning may only be carried out by a qualified electrician.
- The manufacturer accepts no liability for damage caused by improper use or installation.
- If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
- The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
- To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
- You can find them on our website at www.bega.com.
Lamp
- Module connected wattage 12.3 W
- Luminaire connected wattage 14.3 W
- Rated temperature ta =25 °C
- Ambient temperature ta max= 40 °C
50 252.6K3
- Module designation LED -0423/930
- Color temperature 3000 K
- Color rendering index CRI > 90
- Module luminous flux 1640 lm
- Luminaire luminous flux 706 lm
- Luminaire luminous efficiency 49,4 lm/W
Lighting technology
- Half beam angle 48°
Installation
- Luminaire housing must not be installed in heat-insulating material.
- A separate power supply unit is required to operate the luminaire – see accessories.
- The recessed opening will be covered by the frame of the luminaire.
- Fixing of the luminaire is achieved by using 2 adjustable wedge-shaped claws.
- LEDs are high-quality electronic components!
- Please avoid touching them directly during installation or relamping.
Installation into false ceilings
- A recessed opening of ø 68 mm is necessary to accept the luminaire.
- Free space depth min. 100 mm (see sketch).
- Luminaire and external LED-power supply unit must not be installed in heatinsulating material.
- The lateral distance between recessed luminaire and standard combustible building parts must be at least 50 mm.
- The claws catch the panel from the reverse side. If minimum thickness of the panel is less than 3 mm it must be reinforced from the reverse side. Maximum thickness of the panel must be no more than 20 mm.
- For connection to external LED-power supply unit – accessory 13 144 or 13 169 – the luminaire is equipped with a 2-pin connector.
- Note operating instructions of the LED-power supply units.
- Push external LED power supply unit and luminaire into the ceiling cut-out.
- Hand-tight screws of claw fasteners evenly.
- Center reflector onto the enclosed housing shield.
- Mount housing shield with reflector onto luminaire frame (magnetic) (see sketch).
Cleaning · Maintenance
- Clean the luminaire regularly with solvent-free cleansers from dirt.
Replacement of the LED module
- The designation of the LED module is noted on a label in the luminaire.
- The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
- Disconnect the system.
- Pull housing shield with mounted reflector from luminaire frame.
- Please follow the installation instructions for the LED module.
- Mount housing shield with reflector onto luminaire frame (magnetic).
Accessories
- Power supply units for LED luminaires 220-240 V · 0/50-60 Hz with strain relief and plug connector system.
- 13 144 Power supply unit on/off
- 13 169 Power supply unit DALI
- The power supply units are only suitable for the operation of one LED luminaire.
- For the accessories, a separate instructions for use can be provided upon request.
Spares
- Shield 42 000 202 .3M8
- LED module 3000 K LED-0423/930
- Reflector 76 001 317
- BEGA Gantenbrink-Leuchten KG
- Postfach 3160
- 58689 Menden
- info@bega.com
- www.bega.com
Documents / Resources
| BEGA
50252.6 Studio Line Recessed Ceiling Light
LED
[pdf] Instruction Manual
50252.6 Studio Line Recessed Ceiling Light LED, 50252.6, Studio Line Recessed
Ceiling Light LED, Recessed Ceiling Light LED, Ceiling Light LED, Light LED,
LED
---|---