BEGA 24043 LED Ceiling and Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 24043 LED Ceiling and Wall Luminaire
Product Information
Product Usage Instructions
Instructions for use
DIMENSION
Product Description
Safety
FEATURES
Installation
Cleaning Maintenance
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 24043 LED Ceiling and Wall Luminaire

Product Information

Product Name: Decken- und Wandleuchte Ceiling and wall luminaire Plafonnier et applique
Model Number: 24 043
IP Rating: IP 65
Description: This ceiling and wall luminaire features hand-blown, satin matt opal glass for a soft and uniform light distribution. Some of the light exits behind the shield and also illuminates the mounting surface.
Overvoltage Protection: The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. Separate overvoltage protection components are recommended for additional protection against transients. These components can be found on our website at www.bega.com.
Safety: The installation and operation of this luminaire must comply with national safety regulations. Only qualified electricians should perform installation and commissioning. The manufacturer is not liable for any damage caused by improper use or installation. Any subsequent modifications to the luminaire should be carried out by the person responsible for these modifications.

Lamp Specifications:

Module connected wattage: 13.8 W
Luminaire connected wattage: 16.3 W
Rated temperature: ta = 25°C
Ambient temperature: ta = 50°C

Luminaire Performance:

Module Designation| Colour Temperature| Colour Rendering Index (CRI)| Module Luminous Flux| Luminaire Luminous Flux| Luminaire Luminous Efficiency
---|---|---|---|---|---
24 043 K3| LED-0917/830 3000 K| CRI > 80| 2585 lm| 1533 lm| 94 lm / W
24 043 K4| LED-0917/840 4000 K| CRI > 80| 2625 lm| 1557 lm| 95.5 lm / W

Product Usage Instructions

Disconnect the system.
Turn the opal glass with the integrated LED unit to the left as far as it will go, and remove it.
Disconnect the plug-in device. Note: LED components are sensitive, avoid touching the light output opening directly during installation or relamping.
Push the plug into the coupler as far as it will go.
Ensure that the gasket is positioned correctly.
Place the opal glass with LED unit onto the luminaire base, aligning both yellow arrow markers to each other.
Screw the glass clockwise into the base until it reaches the stop position.

Instructions for use

Application

Ceiling and wall luminaire with hand-blown, satin matt opal glass. For a soft and uniform light distribution. Some of the light exits behind the shield and also illuminates the mounting surface.

DIMENSION

$BEGA-24043-LED-Ceiling-and-Wall-Luminaire-FIGH- $1$$

Product Description

Luminaire made of aluminium alloy and stainless steel
BEGA Unidure® coating technology
Opal glass satin matt
Silicone gasket
2 mounting holes ø 5.5 mm
Distance apart 234 mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G 1.5@ Connecting terminal 2.5@
with plug connection
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-276 V
DALI-controllable
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK03
Protection against mechanical impacts < 0.35 joule
Safety mark
Conformity mark
Weight: 2.8 kg
This product contains light sources of energy efficiency classes C

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

FEATURES

Lamp

Module connected wattage 13.8 W
Luminaire connected wattage 16.3 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 50 °C

24 043 K3

Module designation LED-0917/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 2585 lm
Luminaire luminous flux 1533 lm
Luminaire luminous efficiency 94 lm / W

24 043 K4

Module designation LED-0917/840
Colour temperature 4000 K
Colour rendering index CRI > 80
Module luminous flux 2625 lm
Luminaire luminous flux 1557 lm
Luminaire luminous efficiency 95,5 lm / W

Installation

Lead the mains supply cable through the cable entry of the luminaire base.
Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Make the earth conductor connection and the electrical connection.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
Push plug into coupler as far as it will go. Make sure that gasket is positioned correctly. Place the opal glass with LED unit onto the luminaire base in such a way that both yellow arrow markers align to each other and screw the glass clockwise into the base up to the stop.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system.
Turn the opal glass with the integrated LED unit to the left as far as it will go, and remove it. Disconnect the plug-in device.
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
To dismantle the LED unit, the two springs must be removed.
To do this, use a small screwdriver to move the spring clip resting against the hexagon socket screw upwards and over the head of the screw (see drawing A).
The spring can then be removed.
Loosen the hexagon socket screws and take the LED unit out of the opal glass.
Replace the LED modules.
Please follow the installation instructions for the LED module.
Insert the LED unit into the opal glass and secure it in place.
Then insert the springs at the two opposite hexagon socket screws.
Make sure that the spring clip is properly located behind the heads of the screws (see drawing B). $BEGA-24043-LED-Ceiling-and-Wall-Luminaire-FIGH- $2$$
Push plug into coupler as far as it will go. Make sure that gasket is positioned correctly. Place the opal glass with LED unit onto the luminaire base in such a way that both yellow arrow markers align to each other and screw the glass clockwise into the base up to the stop.