BEGA 33523 LED Ceiling and Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 33523 LED Ceiling and Wall Luminaire
Product Information
Instructions for use
Product Usage Instructions
Product Description
Installation
Cleaning · Maintenance
Spares
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 33523 LED Ceiling and Wall Luminaire

BEGA-33523-LED-Ceiling-and-Wall-Luminaire-product

Product Information

The Decken- und Wandleuchte is a ceiling and wall luminaire that is designed for various lighting tasks. It has a high protection class and is made of an aluminium alloy and crystal glass.

The luminaire is available in two models:

Model 33 523 K3:
- Module designation: LED-0381/930
- Colour temperature: 3000 K
- Colour rendering index (CRI): > 90
- Module luminous flux: 1755 lm
- Luminaire luminous flux: 1057 lm
- Luminaire luminous efficiency: 90.3 lm/W
Model 33 523 K4:
- Module designation: LED-0381/940
- Colour temperature: 4000 K
- Colour rendering index (CRI): > 90
- Module luminous flux: 1860 lm
- Luminaire luminous flux: 1120 lm
- Luminaire luminous efficiency: 95.7 lm/W

Instructions for use

Application
Ceiling and wall luminaire with high protection class for a variety of lighting tasks. A luminaire made of aluminium alloy and crystal glass.

Lamp

Module connected wattage
Luminaire connected wattage
Rated temperature
Ambient temperature

33 523 K3

Module designation
Colour temperature
Colour rendering index
Module luminous flux
Luminaire luminous flux
Luminaire luminous efficiency

33 523 K4

Module designation
Colour temperature
Colour rendering index
Module luminous flux
Luminaire luminous flux
Luminaire luminous efficiency

Product Usage Instructions

Safety

Before installing and operating the luminaire, ensure that you comply with national safety regulations. The installation and commissioning should only be carried out by a qualified electrician. The manufacturer is not liable for any damage caused by improper use or installation. If you make modifications to the luminaire, you will be considered the manufacturer.

Overvoltage Protection

The luminaire’s electronic components are protected against overvoltage according to DIN EN 61547. For additional protection against transients and other events, it is recommended to use separate overvoltage protection components. You can find these components on the manufacturer’s website at www.bega.com.

Installation

When installing the luminaire, make sure to only operate it with the complete protective cover. Undo the locking screw and turn the cover ring as far as it will go. Remove the cover ring and glass from the luminaire base. During installation or relamping, avoid touching the light output opening of the LED directly, as they are high-quality electronic components.

Spares

If you require spare parts, the following are available:

Spare glass: 11 002 865
LED power supply unit: 11 DEV-0340/350
LED module 3000 K: LED-0381/930
LED module 4000 K: LED-0381/940
Gasket: 83 001 382

Product Description

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Crystal glass with white matt finish
Silicone gasket
2 mounting holes ø 4.5 mm
Distance apart 200 mm
Two cable entries for through-wiring power connecting cable up to 10.5 mm in diameter, max. 5 x 1.5 qmm.
Connection terminal 2.5@
Earth conductor connection
2-pole connecting terminal for digital control
BEGA Ultimate Driver®
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-264 V
DALI-controllable
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK07
Protection against mechanical impacts < 2 joule
– Safety mark
– Conformity mark
Weight: 2.6 kg
This product contains light sources of energy efficiency classes C, D

Installation

The luminaire must only be operated with the complete protective cover. Undo locking screw and turn cover ring as far as it will go. Remove cover ring and glass from the luminaire base. LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Disassemble LED module. Loosen LED connection (plug connection). Lead the mains supply cable through the cable entry into the luminaire back housing. Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface. Be sure to use the gasket rings supplied. Make the earth conductor connection and the electrical connection. For digital control please use the connecting terminal DA, DA. In case this terminal is not used the luminaire will be operated at full light output. Push LED plug into the coupler as fa as it will go. Make sure that gasket is positioned correctly. Assemble LED module. Tighten the screws evenly. Please observe that the LED board is not damaged mechanically. Place cover ring with glass onto the luminaire base and turn it clockwise as far as it will go. Tighten locking screw.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits. Do not use high pressure cleaners.

Replacing the LED module
The designation of the LED module is noted on a label in the luminaire. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module. Inspect and, if necessary, replace the luminaire gaskets. Defective glass must be replaced. Close the luminaire.