BEGA 24 130 Pendant Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 24 130 Pendant Luminaire Instruction Manual
Instructions for use
Application
Pendant luminaire with unshielded light for mounting in arcades, galleries and
passageways.
When installed in exterior applications, the luminaire must be protected from
constant pendulum movement due to wind.
Lamp
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e.g. transients, etc. we recommend separate overvoltage
protection components.
You can find them on our website at www.bega.com.
Product description
Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Colour white
White synthetic sphere
Silicone gasket
4 drilled holes with thread M4 to which tension cables preventing pendulum
movement can be fixed
Cable pendant H05RN-F 5G1@ with 2 steel cords · Colour black
Overall length of luminaire approx. 3000mm
Mounting plate with 2 fixing holes ø 5.5mm · 70mm spacing
2 cable entries for through-wiring of mains supply cable ø 7-10.5mm, max.
5G1.5@
Connecting terminal 2.5@ with plug connection
Earth conductor connection
BEGA Ultimate Driver®
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-264 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I
Protection class IP 64
Dust-tight and protection against splash water
Impact strength IK10
Protection against mechanical impacts < 20 joule
– Safety mark
– Conformity mark
Weight: 4.4 kg
This product contains light sources of energy efficiency class(es) C
Installation
For mains supply connection open the mounting box. When luminaire is mounted in assembly halls please see that steel cord 1 is closely and under tension fixed to a noninflammable building component – please see sketch. Fix end of steel cord on the back of mounting plate 2 with hexagon socket head screw M5. Lead mains supply cable through the cable entry of the mounting plate. Fix mounting plate with enclosed or any other suitable fixing material onto the mounting surface. It is absolutely essential to use the enclosed gaskets. Make earth conductor connection and electrical connection. Make earth conductor connection between mounting box and mounting plate Plug in plug connection up to the stop. Make sure that the gasket is positiooned correctly. Bolt mounting box firmly together with mounting plate.
To shorten the cable pendant
The cable must only be shortened within the mounting box. Disconnect mains
supply cable from plug connection and earth conductor terminal. Loosen locking
screws – hexagon socket head screws M4 – for suspension cord. Pull suspension
cords out of lock holes. Screw off round nut 3 and pull cable with gasket out
of screw connection. Shorten cable to the desired length. Insert pressure
pressure disk into the round nut and press gasket into the round nut. Grease
connecting cable somewhat and lead it through round nut and gasket. Tighten
round nut as far as it will go and screw it together with the mounting box.
Strip lines and pull suspension cords thightly into the lock holes at the cord
holder.Tighten locking screws M4 firmly. Shorten steel cords with excess
length, protect with end sleeves. Make earth conductor connection and
electrical connection to the connecting terminal (plug connection).
In order to guarantee the maximum service life of the electrical components,
the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the
position marked by the red information label immediately before finally
closing the luminaire.
Insert sphere into holder plate and adjust centrically. Tighten screws at
holder plate evenly.
Make sure that the gasket is positioned correctly
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Cleaning · Maintenance
Clean dirt and debris from the luminaire regularly with a clean, soft, lint-
free cloth that is kept damp throughout the cleaning. If possible, please use
water for this, adding a little commercial dishwashing detergent.
For lacquered surfaces we recommend the use of BEGA Lacquer Care Set 71
179.
Cleaning agents containing solvents and high pressure cleaners are unsuitable
for cleaning and maintenance.
Spares
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>