MODSTER SUV M1 HoverBoard Zoll 350x2W 36V 4Ah schwarz User Manual

MODSTER SUV M1 HoverBoard Zoll 350x2W 36V 4Ah schwarz User Manual

1. Riding Safety

Thanks for choosing the Modster M1. To maximise your enjoyment and safety please read and understand this instruction booklet.

1. The M1 is a recreational product. Before mastering riding skills, you need to practice. Neither the manufacturer nor distributor is responsible for any injuries or damage caused by rider‘s inexperience or failure to follow the instructions in this document.

2. Please understand that you reduce risk by following all the instructions and warnings in this manual, but you cannot eliminate all the risks. Remember that whenever you ride the M1 you risk injury or death from loss of control, collisions, and falls. When entering into public spaces always comply with the local laws and regulations. As with other vehicles, faster speeds require longer braking distance. Sudden braking on smooth surfaces could lead to wheel slip, loss of balance, or falls. Be cautious and always keep a safe distance between you and other people or vehicles when riding. Be alert and slow down when entering unfamiliar areas.

3. Always wear a helmet when riding. Use an approved bicycle or skateboard helmet that fits
   property with the chin strap in place, and provides protection for the back of your head.

4. Do not attempt your first ride in any area where you might encounter children, pedestrians, pets, vehicles, bicycles, or other obstacles and potential hazards.

5. Respect pedestrians by always yielding the right of way. Pass on the left whenever possible. When approaching a pedestrian from the front, stay to the right and slow down. Avoid startling pedestrians. When approaching from behind, announce yourself and slow down to walking speed when passing. Please obey local traffic laws and regulations if Situation is different.

6. In places without laws and regulations goveming self-balancing electric vehicles, comply
   with the safety guidelines outlined In this manual. Neither the manufacturer nor distributor is responsible for any property damage, personal injury/death, accidents, or legal disputes caused by violations ofthe safety lnstructions. Do not allow anyone to ride your M1 on his/her own unless they have carefully read this manual, or watched the safety video.

7. The safety of new riders is your responsibility. Assist new riders until they are comfortable with the basic operation of the M1, make sure each new rider wears a helmet and other protective gear.

8. Before each ride check for loose fasteners, damaged components, and low tire pressure. lf
   the M1 makes abnormal sounds or signals an alarm, lmmediately stop riding and switch the machine off. lf alarm persists, contact the retailer where you purchased your M1 .

9. Be alert! Scan both far ahead and in front of your M1 – your eyes are your best tool for safely avoiding obstacles and low traction surfaces (including, but not I imited to, wet ground, loose sand, loose gravel, and ice).

10. To reduce risk of injury, you must read and fol low all „CAUTION“ and“WARNING“ notices in this document. Do not ride at an unsafe speed. Under no circumstance should you ride on roads with motor vehicles. Riders need to be at least 12 years old.
    Always follow these safety instructions:
    A. People who should not ride the M1 include:
    i. Anyone under the influence of alcohol or drugs.
    ii. Anyone who suffers from disease that puts them at risk if they engage in strenuous
    physical activity.
    iii. Anyone who has problems with balance or with motor skills that would interfere with
    their ability to maintain balance.
    B. Anyone whose height or weight is outside the stated limits (see Specifications).
    C. Pregnant women.
    B. Riders under the age of 12 years old must ride under adult supervision.
    C. Comply with local laws and regulations when riding this product. Do not ride where
    prohibited by local laws.
    D. To ride safely, you must be able to clearly see what is in front of you and you must be
    clearly visible to others.
    E. Do not ride in the snow, in the rain, or on roads which are wet, muddy, icy, or that are
    slippery for any reason. Do not ride over obstacles (sand, loose gravel, or sticks). Doing so could result in a loss of balance or traction and could cause a fall.
    F. Do not accelerate or decelerate suddenly. Do not accelerate when the M1 tilts back or
    sounds an alarm. Do not attempt to override the speed limiter.

11. Do not attempt to charge your M1 if the charger, or the power outlet is wet.

12. As with any electronic device, use a surge protector when charging to help protect your M1 from damage due to power surges and voltage spikes. Only use the supplied charger. Do not use a charger from any other product.

13. Use only our approved parts and accessories. Do not modify your M1 . Modifications to your M1 could interfere with the operation of the product, and could result in serious injury and/or damage, and could avoid the Limited Warranty.

14. Do not sit on the M1 SUV. Doing so could result in serious injury and/or damage to your M1.

2. Packing List

Mainframe

When unpacking your M1 , please verify that the above items are included in the package. lf you are missing any components, please contact your dealer/distributor. After verifying that all components are present and in good condition, you can assemble your new M1.

Please retain the box and packaging materials in case you need to ship your M1 in the
future.

Always power off your M1 and unplug the chargingcable before assembling, mounting.

3. Diagram

4. Charging

Do not connect the charger if the charge port or charge cable is wet. Your M1 is fully charged when the LED on the charger changes from red (charging) to green (trickle charge). Close the rubber cap when not charging

5. First Ride

There are safety risks when learning to ride the M1 . You must read the Safety lnstructions
before your first ride. For your safety, your M1 is not activated at this time and will beep occasionally after Power ON.

SETTING YOUR HOVERBOARD TO DIFFERENT MODES:
The hoverboard is shaking, it is a little dangerous , whats the problem?
lf shaking, it‘s possible that the user‘s weight is not enough for the hoverboard, you can adjust it to child mode by following these instructions:

Stand the M1 on its side, press the power button to turn it on – release the button – then keep it pressed for about 6 seconds. The hoverboard will emit a beep, and the hoverboard is now in child mode.

7. The speed of two sides of the wheel is different/ I can not turn fluently with the hoverboard/ one side of the pedals is not on the horizontal line when starting up, what should I do?

The hoverboard is losing balance now, please calibrate it. Confirm that the hoverboard is in the off state and keep both side of the pedals parallel to the horizontal plane.

Make sure the hoverboard is turned off, press and hold the power switch for 5 seconds and
then release it. When you hear a sound, the system starts to calibrate; the red light (that is, the running indicator and the left turn indicator) flashes 3 times.

Wait until the red light is on to confirm the system calibration is confirmed. Turn the hoverboard off again, and next time you switch it on the calibration will be completed.

8. l‘m an experienced rider, I do not like the self-balance, can I cancel it?
Yes, you can cancel the self-balance aspect of the hoverboard. Place the board horizontally-make sure it is turned on, press the power switch for about 6 seconds, until you hear the beep sound, restart the hoverboard to complete the adjustment.

9. When I stop riding, the M1 is shaking heavily, is it normal?
lf you slow down and come to a stop suddenly, the M1 will shake for a few seconds. This is
caused by the internal self-balancing gyroscopes. To prevent this shaking, slow down
gradually, not suddenly. You can also adjust it to child mode (see above how to do this)

10. What should I do if there are problems with my Hoverboard?
lf you have any problems with your M1 , please contact the place of purchase.

6. Learning to Ride

7. Warning

You must read and understand the Warnings and Safe Riding instructions in this manual before attempting to ride the M1 . Failure to follow these warnings could result in death or
serious injury due to: loss of balance, traction, and/or control; collisions; and falls.

8. Maintenance

Cleaning and Storing Your M1
Use a soft, wet cloth to wipe the mainframe clean. Hard to remove dirt can be scrubbed
with a toothbrush and toothpaste. Then cleaned with a soft, wet cloth. Scratches on plastic
parts can be polished with extra fine grit abrasive paper.

NOTE
Do not wash your M1 with alcohol, gasoline, acetone, or other corrosive/volatile solvents.
These substances may damage the appearance and internal structure of your M1. Do not
wash your M1 with a power washer or high pressure hose.

! WARNING
Make sure the M1 is powered OFF, the charging cable is unplugged, and the rubber cap
on the charge port is tightly sealed before cleaning; otherwise you may expose yourself to
electric shock or damage the electronic components.

Store your M1 in a cool, dry place. Do not store it outdoors for extended periods of time.
Exposure to sunlight and temperature extremes (both hot and cold) will accelerate the
aging process of the plastic components and may reduce battery life.

Battery Pack Maintenance
Do not store or charge the battery at temperatures outside the stated limits rmation, refer to the sticker on the battery itself, located on the bottom.

Refer to your local laws and regulations regarding battery recycling and/or disposal.

A weil maintained battery can perform weil even after many miles of riding. Charge the battery after each ride and avoid draining the battery completely. When used at room temperature (70°F [22°q) the battery range and performance is at its best; whereas using it at tem peratures below 32°F (0°C) can decrease range and performance. Typically, at-4°F
(-20-C) range can be half that of the same battery at 70-F (22°C). Battery range will recover when temperature rises.

NOTE
Typically, a fully charged battery should retain charge for 60-90 days in Standby Mode. Remember to charge the battery after each use. Completely draining the battery may cause permanent damage to the battery. Electronics inside the battery record the charge-discharge condition of the battery; damage caused by over-discharge or under discharge will not be covered by the Limited Warranty.

!WARNING
Do not attempt to disassemble the battery. Risk of fire. No user serviceable parts.

!WARNING
Do not ride when the ambient temperature is outside the machine operation temperature (see Specifications) because low/ high temperature will limit the maximum power/torque. Doing so could cause personal injury or property damage due to slips or falls.

Never charge the battery unobserved!
Do not drive in the rain, in wet conditions or on dusty or muddy ground!

Range information, as well as information on maximum speeds and incline ability are heavily
dependent on parameters such as the state of charge of the battery, condition of the ground, inclines or declines during the route, weight of the person driving, physical performance by diving or, if available, use of the pedals, weather conditions, headwind and depending on other factors. Our information relates to the optimal case.

9. Specifications

10. Calibration and Alarms

Calibration
When in Balance Mode, if the M1 moves forward or backward on its own on flat ground, it
needs to be calibrated if the problem persists, please contact after-sales service.

To Calibrate the M1
Confirm that the hoverboard is in the off state and keep both side of the pedals parallel to the horizontal plane. Make sure the hoverboard is turned off, press and hold the power switch for 5 seconds and then release it. When you hear a sound, the system starts to calibrate; the red light (that is, the running indicator and the left turn indicator) flashes 3 times. Wait until the red light is on, the system calibration is configured. Turn it off and on again and you can use the hoverboard again

Self-balance Mode
Place the car horizontally-make sure the M1 is turned on,press the power switch for about 6
seconds, until you hear the beep, then restart the hoverboard. The adjustment is complete.

Child mode/ Adult mode
Stand the M1 up on its side. Press the power button to turn it on -release the button -then
keep it pressed for about 6 seconds until the beep is heard and the hoverboard is restarted.
Perform the same action to switch back to original mode.

Alarms
Overheating Riding for an extended period of time could increase the internal temperature
of your M1 in excess of 122°F(S0° C). lf this happens, the glow lights will flash red, an alarm
will sound and your M1 will not be able to charge. Simply step off the hoverboard, power it
off, and give it time to cool back down to a normal operating temperature

Other alarms
For any other alarms, try restarting your M1 . lf the problem persists, please contact
after-sales service.

11. App

FAQ

1. How to download app?****

Please download by searching“Gyroor scooter”on app store or google play.

2. How to connect app and bluetooth speaker?****

For the app , after you download open it , you can see a sign for bluetooth on the upper left corner, click it you will enter a new page , then choose scan , when you see the „Hoverboard Name“, click it will show connect successfully.
For connecting the bluetooth speaker of the Hoverboard, please open the bluetooth on phone setting and search , the name of bluetooth is like “12:13:34:58:33:9C”, when successfully connected , it will change into“Wheel- music”.

3. I can not find the bluetooth for app or bluetooth speaker, does it support app and bluetooth speaker function?****

The Hoverboard support app and bluetooth speaker function, if you can not find the bluetooth , please restart the hoverboard or phone . If it still can not connect successfully, please try another smartphone with different system.

4. I can not connect the app /bluetooth, what should I do?****

If you can not connect the app or bluetooth speaker, please restart the Hoverboard or phone . if it still can not connect successfully, please try another smartphone with different system. If you need , please contact the MODSTER customer service under customersupport@modster.at.

5. Do you have any suggestion for a new user?****

a. For beginners, please practice on a flat ground, and adjust it to child mode.
b. Step on one foot at a time.
c. If having issues on stabilizing yourself, try pressing your feet against the outer edge.
d. Make sure that you have someone or something to hold on.
e. Step off backwards, not forwards.
f. Tilt both your feet forward to go straight.
g. Tilt them back to go backwards.
h. Slightly tilt your right foot to turn left.
i. Slightly tilt your left foot to turn right.
j. You can get through tighter spaces by moving the board back and forth.
k. Try not to freak out when getting on, confidence is key,be confident and just relax.
l. Just have some fun with it for a few minutes that you can master it well.

6. The hoverboard is shaking, it is a little dangerous , what`s the problem?****

If shaking, it‘s possible that the user‘s weight is not enough for the hoverboard, you can adjust it to child mode by gyroor app or adjust by hands. App adjustment: conversion of adult mode and child mode Manual adjustment: Stand up the Hoverboard, press the power button to turn it on – release the button – then kee press. The button remains for about 6 seconds until the drip sound is heard and the balance hoverboard is restarted. Complete child mode switching.

7. The speed of two sides of the wheel is different/ I can not turn fluently with the hoverboard/ one side of the pedals is not on the horizontal line when starting up , what should I do?****

The hoverboard is losing balance now, please calibrate it. Confirm that the hoverboard is in the off state and keep both side of the pedals parallel to the horizontal plane. Make sure the hoverboard is turned off , press and hold the power switch for 5 seconds and then release it. When you hear a sound, the system starts to calibrate; the red light (that is, the running indicator and the left turn indicator) flashes 3 times. Wait until the red light is on, the system calibration is complete, and you can cycle when you turn it off and on again.

8. I’m an experienced rider, I do not like the self–balance, can I cancel it?****

Yes, you can canceled it, adjust it by gyroor app or hands: App adjustment: conversion of self-balance and unself-balance. Manual adjustment: Place the car horizontally – make sure the Hoverboard is turned on, press the power switch for about 6 seconds, until you hear the drip sound, restart the mode to complete the mode switch.

PLEASE SCAN THE FOLLOWING TWO CODES FOR EXPERIENCE WITH YOUR SMARTPHONE (The App Version continuosly updated)

Disclaimer of warranties

• The maximum total weight and load must not be exceeded. High loads in connection with overloading operation of the device can lead to structural damage. Jumping with the device is not allowed and leads to loss of warranty, as well as driving through potholes and the like. Driving on cobblestones leads to increased wear!
• Only one person is allowed to drive at the sametime.
• The device is designed for operation on flat, smooth surfaces. It must not be used on sandy, muddy, wet, slippery, icy or snow-covered floors. Driving in rain and snow is not allowed.
• Do not disassemble the device yourself. This leads to LOSS OF WARRANTY.
• Do not store the devicle with empty batteries. The battery must be recharged every month.
• Cleaning the device with high pressure cleaners is not permitted. Wipe only with a damp cloth.
• Depending on the load, the device is subject to more or less severe wear. This can lead to deflection of the steering, wheel bearings, folding mechanism and the like; this is not covered by the waranty. Brakes, tires, drive chains and sprockets are wearing parts and are not covered by the warranty. The drive battery is designed for 200 charging cycles. A gradual decrease in performance cannot be avoided and is not covered by the warranty.
• Store the device in a dry place at a temperature between 10° – 30°C.
• Only use the original charger.
• Do not exceed the design speed of the device. This can easily be exceeded, especially when driving downhill.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>