BEGA 50313K27 LED Ceiling and Wall Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50313K27 LED Ceiling and Wall Luminaire Instruction Manual
Ceiling and wall luminaire for indoor use
Application
Ceiling and wall luminaire · indoor luminaire made of hand-blown opal glass
and metal housing, for all lighting tasks. They are ideal for places where a
soft and uniform lighting distribution is required.
Luminaire with motion sensor.
Product description
Metal housing, finish Colour white Hand-blown opal glass, satin matt Integrated HF-motion sensor, maximum range 10 m 2 mounting holes ø 6mm Distance apart 230mm 2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@ Connection terminal 2.5@ Earth conductor connection LED power supply unit 230 V y 50 Hz BEGA Thermal Switch® Temporary thermal shutdown to protect temperature-sensitive components Safety class I Impact strength IK03 Protection against mechanical impacts < 0.35 joule
– Conformity mark
Weight: 3.6 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components. You can find them on our website
at www.bega.com.
Lamp
Module connected wattage : 23.1 W
Luminaire connected wattage : 27.7 W
Rated temperature : ta=25 °C
Ambient temperature : ta max=40 °C
50 313K27
Colour temperature : 2700 K
Colour rendering index : CRI >90
Module luminous flux : 3710 lm
Luminaire luminous flux : 2679 lm
Luminaire luminous efficiency : 96,7 lm/W
50 313K3
Color temperature : 3000 K
Color rendering index : CRI >90
Module luminous flux : 3760 lm
Luminaire luminous flux : 2716 lm
Luminaire luminous efficiency : 98,1 lm/W
Notice prior to installation:
Luminaire with trim frame The luminaire housing must be inserted in the trim
frame (accessory) before it is mounted onto the mounting surface.
Make sure that the two openings in the trim frame coincide with the positions
of the grub screws of the luminaire housing.
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Lead mains supply cable through the cable entry into the luminaire housing.
Fix the luminaire housing with enclosed or any other suitable fixing material
onto the mounting surface.
It is imperative to use the enclosed gaskets.
Make earth conductor connection.
Push silicone sleeves over the lines and make electrical
connection.
Position the glass over the luminaire housing so that the retaining springs
fit into the two recesses in the raised edge of the glass.
Press the glass against the retaining springs at a flat angle as far as it
will go and push it into the luminaire housing (see drawing).
Gentle pressure on the glass will fix it in the luminaire housing through the
three lobes on the opposite side.
IMPORTANT:
If the luminaire is to be installed on the ceiling, it is essential that the
two grub screws (Allen screws) should be screwed with gentle pressure against
the retaining springs. In this way, the glass is held securely in place and is
resistant to vibration.
Brightness
Dwell time
Sensitivity
The built-in motion sensor operates at a frequency of 5.8 GHz.
By moving within the detection range the motion sensor switches on the LED
module inside the luminaire with a defined dwell time – push-button “Dwell
time”.
With a wall mounting height of 1.8 m or ceiling mounting height of 2.6 m, the
maximum range is 10 meters (see sketch).
Wall ·
Ceiling
Detection range
The max. wall mounting height is 2.7 m and the max. ceiling mounting height is
4.0 m, in which the range reduces significantly.
The range can be set individually – push-button “Sensitivity”.
It should be noted that metal parts which are mounted in close proximity to
the luminaire can affect the range.
With the three integrated push-buttons (Brightness, Dwell time and
Sensitivity) on the motion sensor, specific settings can be made.
The first keypress activates the setting function.
Press a push-button to switch each function to the next level, the LED
indicator on the motion sensor flashes to confirm.
After reaching the highest level, the level setting begins with “Level 1”.
Number of flashes
Step
Setting of brightness
TASTE
BUTTON
BOUTON
Number of flashes
Step
Setting of dwell time
TASTE
BUTTON
BOUTON
Number of flashes
Step
Setting of Sensitivity / Range
TASTE
BUTTON
BOUTON
After the 3 parameters brightness, dwell time and sensitivity have been set
successfully the module will require a voltage break to save the changes.
The integrated light sensor can be set individually with the brightness levels
on the ambient brightness – Press the button
“Brightness”.
Further individual illumination levels can be used with the button
“Brightness” and set with the “learning mode”.
Press button “brightness” (> 3 s) to enable the “learning mode”. There is a
slow flashing of the LED indicator.
After about two minutes, the current brightness value is measured for one
minute, the LED flashes faster.
After completion, the measured brightness value is saved and is available in
stage 6 of “Brightness” as the new brightness value.
To simplify the initial operation, the settings have been made as follows:
Range = 75 % (7.5 m)
Dwell time = 10 s
Light sensor = daylight
Factory Reset
The motion sensor can be reset to factory settings (MICAS) by simultaneously
pressing the buttons “Sensitivity” and “Dwell time” for about 5 s.
The factory settings are as follows:
Range = 75 % (7.5 m)
Dwell time = 900 s
Light sensor = daylight
Test mode
The test mode can be used to check the change of settings of the motion
sensor. Press button “Sensitivity” (> 3 s) to enable the
“test mode”.
Each further keystroke of this push-button prolongs the test mode.
The active test mode is displayed by a flashing of the LED indicator (2 s
interval).
After 3 minutes the test mode is automatically disabled.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Opening the luminaire
Unscrew the two grub screws (Allen screws) of the luminaire housing as far as
they will go.
A recess (identifiable by touch) in the edge of the glass indicates the
direction from which the luminaire glass must be pressed against the spring
pressure of the glass retaining springs in order to release it from the
luminaire housing.
Pull the glass away from the luminaire housing against the holding force of
the retaining springs and remove it.
Replacement of the LED unit
The designation of the LED unit is noted on a label in the luminaire.
The light colour and light output of BEGA replacement units correspond to
those of the LED units originally fitted. The LED unit can be replaced by
qualified persons using standard tools.
Disconnect the system and open the luminaire.
Replace the LED unit.
Close the luminaire.
A damaged glass must be replaced
Accessory · Trim frames
For this luminaire metal trim frames in 3 enamel surfaces are optional
available.
Trim frames are accessories and must be ordered separately.
Bestellnummer
13 137 Colour white
138 Colour palladium
3 139 Colour glossy silver
Spares
Spare glass : 11 003 279 .0RG
HF-motion sensor : 61 001 077
LED unit : 2700 K 75 002 982 K27
LED unit : 3000 K
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden · info@bega.com · www.bega.com
Documents / Resources
| BEGA
50313K27 LED Ceiling and Wall
Luminaire
[pdf] Instruction Manual
50313K27, 50313K3, 50313K27 LED Ceiling and Wall Luminaire, LED Ceiling and
Wall Luminaire, Ceiling and Wall Luminaire, Wall Luminaire, Luminaire
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>