BEGA 50710.4 LINE LED Ceiling Luminaire Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
BEGA 50710.4 LINE LED Ceiling Luminaire Instruction Manual
BEGA
Deckeneinbauleuchte für die Verwendung im Innenbereich
Recessed ceiling luminaire for indoor use Plafonnier à encastrer pour
utilisation à l’intérieur
Recessed ceiling luminaire for indoor use
Instructions for use
Application
Recessed ceiling luminaire · indoor luminaire partially satin matt crystal glass inside and aluminium alloy housing.
For installation into ceilings with a shallow depth in interior areas.
Product description
Recessed ceiling luminaire »ACCENTA« Die-cast aluminium housing
Crystal glass, partially satin matt inside Reflector made of pure, high-gloss anodized aluminium
Ceiling trim ring finish, Brass Recessed opening ø 68 mm Required installation depth 60 mm
Fixing is achieved by using 2 adjustable
wedge-shaped claws
External LED power supply unit 220-240 V x 0/50-60 Hz
Safety class II 2 r – Safety mark c – Conformity mark Weight: 0.22 kg
This product contains light sources of energy
efficiency class(es) E
Safety
The installation and operation of this luminaire
are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against
e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at
Lamp
Module connected wattage 8.5 W
Luminaire connected wattage 10.4 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 35 °C
50 710.4 K27
Module designation LED-0923/927
Colour temperature 2700 K
Colour rendering index CRI > 90
Module luminous flux 1155 lm
Luminaire luminous flux 581 lm Luminaire luminous efficiency 55,9 lm / W
50 710.4 K3
Module designation LED-0923/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 1200 lm
Luminaire luminous flux 604 lm Luminaire luminous efficiency 58,1 lm / W
Installation
l Luminaire housing must not be installed in
heat-insulating material.
LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
The recessed opening will be covered by the frame of the luminaire.
Fixing of the luminaire is achieved by using 2 adjustable wedge-shaped claws.
Installation into false ceilings
A recessed opening of ø 68 mm is necessary to accept the luminaire housing. Free space depth min. 60 mm (see sketch).
The claws catch the panel from the reverse side. If minimum thickness of the panel is less than 3 mm it must be reinforced from the
reverse side. Maximum thickness of the panel
must be no more than 20 mm.
Remove cover of the external LED-power
supply unit.
Loosen set screws of cable strain relief. Tightening zone for strain relief: max. Ø 12mm. Connecting terminals for mains supply:
max. 2,5@.
Strip the wires 6 mm.
Lead mains supply cable through the cable
strain relief and fix set screws.
Make electrical connection.
Close case cover of the external LED-power
supply unit and press it until it is locked. Push external LED-power supply unit and luminaire housing into ceiling cut-out.
Luminaire housing and external LED- power supply unit must not be installed in heat-insulating material.
Hand-tight screws of claw fasteners evenly. Lead enclosed ceiling frame ring over the screw-neck of the glass and push it down the gasket.
Make sure that gasket is positioned correctly. Insert glass with mounted reflector and frame ring by turning it clockwise into luminaire housing.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Defective glass must be replaced.
Replacement of the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by
qualified persons using standard tools.
Disconnect from main supply.
Unscrew glass with ceiling frame ring from luminaire housing by turning it
counter- clockwise.
Please follow the installation instructions for the LED module.
Check gasket. Screw in glass with ceiling frame ring by turning it clockwise
beyond the stop.
Defective glass must be replaced.
Spares
LED module 2700 K LED-0923/927
LED module 3000 K LED-0923/930
Trim ring 72 009 587 L
Reflector 76 001 209
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>