BEGA 50818.4 LED Wall Luminaire for Indoor Use Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
Wall luminaire for indoor use
50 818.4
Instructions for use
Technical amendments reserved
Application
Wall luminaire · indoor luminaire with velvet white luminaire housing and inside hue. Luminaire with shielded light source for illumination of wall surfaces with the mounting surface being the reflection surface. The light emits upwards and downwards.
Product description
Wall luminaire “STUDIO LINE” Luminaire housing made of aluminium, surface
Colour velvet white inside hue matt brass Light-diffusing synthetic LED cover
2 elongated fixing holes Width 4.5 mm · 210 mm spacing 1 cable entry for
through-wiring for mains cable Connection terminal 2.5@ Earth conductor
connection LED power supply unit
220-240 V 0/50-60 Hz DC 176-280 V BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components Safety
class I
– Safety mark
– Conformity mark
Weight: 0.9 kg
This product contains light sources of energy efficiency class(es) D
Lamp
| Module connected wattage | 11.8 W |
|---|---|
| Luminaire connected wattage | 13.7 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 55 °C |
50 818.4 K3
| Module designation | LED-0393/930 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 90 |
| Module luminous flux | 1840 lm |
| Luminaire luminous flux | 778 lm |
| Luminaire luminous efficiency | 56,8 lm / W |
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Installation
Undo the hexagon socket head screws (wrench size 2.5 mm) and lift luminaire
housing. LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Loosen earth connection (plug connection) and LED-connection (plug – plug
socket) between luminaire housing and mounting plate. Pass the power
connecting cable through the cable entry in the mounting plate.
Fasten the mounting plate with the supplied fastening material or other
suitable fastening material to the installation surface. Make sure to use the
gaskets supplied. Establish earth conductor connection and make the electrical
connection to the terminals.
Restore the earth conductor connection (plug contact) and LED connection
(plug– jack) between the luminaire housing and the mounting plate. Install
luminaire housing onto the mounting plate and tighten hexagon socket head
screws evenly.
Carefully insert the supplied shield into the luminaire housing. Make sure
that in its final position, the shield engages with its magnetic underside
flush to the profile groove of the luminaire housing.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by
qualified personnel using standard tools.
Disconnect the system from the mains.
Undo the hexagon socket head screws (wrench size 2.5 mm) and lift luminaire
housing. Loosen earth connection (plug connection) and LED-connection (plug –
plug socket) between luminaire housing and mounting plate.
In order to loosen the screw connection of the LED module, first loosen the
hexagon nuts on the inside and remove the metal plate from the luminaire
housing. Remove the loose luminaire cover.
Press the synthetic LED cover together lengthwise and remove it from the
housing profile.
Remove the LED module. Install the replacement LED module.
Please follow the installation instructions for the LED module.
A defective LED cover must be replaced.
Install the luminaire again in the reverse order.
Spares
Synthetic cover 15 000 601 B1
LED power supply unit DEV-0136/700
LED module 3000 K LED-0393/930
Shield 72 003 359 B2
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>