anslut YDA-50D-S3P-W Smart Air Dehumidifier Instruction Manual

anslut YDA-50D-S3P-W Smart Air Dehumidifier

Jula AB reserves the right to make changes to the product. Jula AB claims copyright on this documentation. It is not allowed to modify or alter this documentation in any way and the manual shall be printed and used as it is in relation to the product. For the latest version of operating instructions, refer to the Jula website.

SAFETY INSTRUCTIONS

Read these instructions carefully before use.

• This product can be used by children from 8 years of age and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved. Keep children under supervision to make sure they do not play with the product. Do not allow children to use, clean or maintain the product without supervision.

• The product is not intended to be used by persons (children or adults) with any form of functional disorders, or by persons who do not have sufficient experience or knowledge on how to use it, unless they have received instructions concerning the use of the product from someone who is responsible for their safety.

•  A damaged power cord or plug must be replaced by an authorised service centre or other qualified personnel to ensure safe use.

• The product must be installed in accordance with the instructions and local regulations.

• Maintenance and any repairs should be carried out by qualified personnel.

• Do not connect the product to a power point that is loose or otherwise damaged.

• Do not use the product in damp or wet areas.

• The product must only be used for its intended purpose and in accordance with these instructions.

• Switch off the product immediately and pull out the plug if the product tips over or falls when in use. Check for any visible damage to the product. Contact an authorised service centre or other qualified personnel if the product is damaged.

• Switch off the product and pull out the plug during thunder storms – lightening can damage the product.

• Do not use the product with a speed controller – risk of electric shock.

• Do not route the power cord under carpets etc. Do not route the power cord under furniture or other appliances. Place the power cord so that there is no risk of treading on it, or tripping over it.

• Never attempt to open the product when it is in use.

• Be careful not to touch the metal parts on the product when removing the air filter.

• Do not pull the power cord to unplug the plug.

• Empty the water container before restarting the product, to avoid overflowing/or spillage.

• Do not tilt the product, it can be damaged by running water.

• Pull out the plug if the product is not going to be used for some time.
  NOTE

• Always follow the basic safety instructions when using electrical products. Failure to follow all the instructions and safety instructions can result in the risk of fatal injury, electric shock, fire and/or serious personal injury.

ELECTRICAL DATA

• The technical data for the product is specified on the type plate on the back of the product.

• The plug must be plugged into a correctly installed and earthed power point.

• Check that the mains voltage corresponds to the rated voltage on the type plate.

• Never modify the plug in any way. Allow an authorised electrician to install an earthed power point if the plug does not fit in the power point. The power point must be fused for the product’s maximum power consumption (specified on type plate).

• Do not use an extension cord unless absolutely necessary. If using an extension cord, it must be approved for the product.

• Pull out the plug before cleaning, service and/or any other intervention.
  WARNING
  

• Never use other objects or methods than those recommended by the manufacturer to clean the product.
  

• Store the product in a room without sources of heat, such as naked flame, LPG products, electric heaters, etc.
  

• The floor area in the room where the product is installed must be at least 4 m².
  

• Do not overload the power point or connection. Risk of electric shock and/or fire as a result of overheating.
  

• Do not start/stop the product by disconnecting/ reconnecting the power supply. Risk of electric shock and/or fire as a result of overheating.
  

• Do not use a damaged or unsuitable power cord. Risk of fire and/or electric shock.
  

• Never modify the power cord or plug. Risk of electric shock and/or fire as a result of overheating.
  

• Do not touch the power cord or the plug with wet hands. Risk of electric shock. • Do not place the product near sources of heat. Plastic parts can melt. Risk of fire.
  

• Switch off the product immediately and pull out the plug in the event of any abnormal noise, smell, smoke or other sign of a problem. Risk of fire and/or electric shock.
  

• Do not dismantle the product or attempt to modify, or repair it. Risk of material damage and/or electric shock.
  

• Switch off the product and pull out the plug before cleaning. Risk of electric shock and/or personal injury.
  

• Do not use the product near flammable liquids or gas. Risk of explosion and/or fire.
  

• Switch off the product before removing the water container. Risk of damaging the float switch, and/or risk of electric shock.
  

• Do not use the product in a confined space. Inadequate ventilation can cause a fire risk as a result of overheating.
  

• Do not expose the product to splashing water. Water that gets into the product can damage the insulation and result in a risk of electric shock and/or fire.
  

• Place the product on a level, stable surface. If the product tips over water can run out and cause material damage and a risk of electric shock and/or fire.
  

• Never poke your fingers or any other objects into the inlet or outlet openings. Risk of electric shock and/or material damage.
  

• Do not place heavy objects on the power cord. Place the power cord so that it cannot be stood on, or clenched. Risk of fire and/or electric shock.
  

• Do not step or sit on the product. The product can tip over – risk of personal injury.
  

• Always make sure to fit the filter properly. Clean the filter every other week. Never run the product without a filter – risk of material damage.
  

• If water gets into the product, switch it off, pull out the plug and contact an authorised service centre or other qualified personnel. Risk of personal injury and/ or material damage.
  

• Never place objects filled with water, such as vases, on the product. Water that gets into the product can damage the insulation and result in a risk of electric shock and/or fire.

SYMBOLS

| Read the instructions.
---|---
| Approved in accordance with the relevant directives
| Recycle discarded product in accordance with local regulations
| Fire risk  flammable material
---|---

TECHNICAL DATA

Voltage 230 V
Output 750 W
Tank volume 50 l
Cord length 1.7 m
Size W 380 x H 615 x D 275 mm
Weight 18.7 kg

DESCRIPTION

Front

1. Air deflector

2. Control panel

3. Cap for water container

4. Front casing

5. Handle for water container

6. Back casing

7. Water container
   Back

8. Handle

9. Filter frame

10. Outlet

11. Cord retainer

12. Wheel

Control panel

1. Timer button
   For setting of timer 24 h. Press this button to  set the time to switch on and off from 1 to 24hours. To cancel the set timer programming, press the timer button twice after confirmation.

2. Button for drying mode
   Press this button to start drying the product. This button is used to prevent mould developing in the product. The process takes about 1 hour. Press the button again to stop the drying function and reset the product to the run mode it had before the drying function was started.

3. Air speed
   Select HIGH or LOW air speed in automatic mode (AUTO) or continuous mode (CONTINUOUS).

4. Display
   In AUTO and CONTINUOUS mode the display shows the humidity in the room. When setting the humidity in AUTO mode the display shows the set humidity in %. The set time is shown in timer mode.

5. Setting the humidity
   Press this button to set the required humidity. Each time the button is pressed the set value changes in the order of 30% – 35% – 40% – 45% – 50% – 55% – 60% – 65% – 70% – 75%  – 80%. This setting is only applicable in AUTO mode.
   Press the button for 3 seconds to switch on or switch off the pump function.

6. Button to sett run mode
   Press this button when the product starts to select AUTO, CONTINUOUS mode etc.. The status light for the selected mode goes on. Keep the button pressed for 3 seconds to activate the child lock. Repeat to deactivate the child lock.

7. Power switch
   Press the power switch to start/stop the product.

USE

• Before using for the first time, take out the filter frame and put the filter with active carbon in it.

• Never start the product without filter.
  1. Filter with active carbon
  2. Filter frame
  

• Empty the water container before use.

• Keep doors and windows closed for best dehumidification and minimum consumption of energy.

• Leave at least 50 cm of free space over the product and at least 20 cm on all sides.
  

• The vibration of the product can cause noise. To avoid this it is recommended to place the product on a rubber mat or the  equivalent. Use a rubber mat when necessary to prevent the feet on the product leaving marks on the floor.

FUNCTIONS

Setting the timed stop

When the product is on, press the timer button to set the required time from 1 to 24 hours. The time is increased by 1 up to 24 hours each time the button is pressed, after which is shows 1 again. If the timer button is held pressed in the time shown is browsed in a circle. The product switches off automatically when the set time has expired. The time set is confirmed automatically after 5 seconds without pressing the button. The light in the timer button goes on when timer mode is activated

Setting the timer to start

When the product is in standby mode, set the required time for the timer to start according to the above instruction for setting the timed stop. The time set is confirmed automatically after 5 seconds without pressing the button. The light in the timer button goes on when timer mode is activated and the set time is shown on the display.

AUTO mode

Select AUTO mode. If the humidity in the room exceeds the set value by more than 5% the compressor starts and the fan runs at the set speed. If the humidity in the room is between 5% over and 5% under the set value the compressor starts and the fan runs at the set speed. If the humidity in the room is less than the set value by more than 5% the compressor switches off, but the fan runs at the set speed. The standard setting for humidity is 50%.

CONTINUOUS mode

In CONTINUOUS mode the compressor works irrespective of the humidity in the room. The fan runs as standard at high speed. The fan speed can be set with the button for the air speed.

Drying mode

Press the button for drying mode to start the drying function. The process takes about 1 hour.

1. The product starts at high speed (HIGH) and runs for 30 minutes.
2. The fan switches to low speed (LOW) and runs for 20 minutes.

Deactivation

1. Press the button again to stop the drying function and reset the product to the run mode it had before the drying function was started.
2. Press the power switch to stop the drying function and put the product in standby mode.

Indication of humidity

Press the button for selecting run mode and the button for setting the humidity at the same time to activate/switch of indication of  humidity. When the function is activated the humidity is indicated by the colour of the light strip on the front of the product. Reed indicates high humidity (over 60%), green medium humidity: (40 to 60%), blue low humidity (less than 40%).

Pump function

Press the button for setting the humidity for 3 seconds to switch on or switch off the pump function. Connect en emptying hose before starting the pump function.

Oscillation

Press the timer button and the button for drying mode at the same time to activate the oscillation function.

EMPTYING

Using the water container

When the water container is full the status light for full container goes on and the buzzer gives 10 audio prompts. The compressor, fan and deionisation unit stop.
Carefully pull out the water container with the handles on the sides. Open the cap on the right side and pour out the water.

Close the cap on the water container. Carefully replace the water container in the product to restart the product.

NOTE:
Empty the water container when it is full. Check that the float moves freely and then press the water container in place with both hands.

Emptying with hose

A hose can be connected to avoid manual emptying of the container.

Without pump function

a. Connect a hose with an outer diameter of 13 mm to the back of the product.

1. Remove the casing over the connection and remove the plug.
2. Connect a hose with a diameter of 13 mm.

b. Use a hose with standard thread with an outer diameter of 1 1/16 inches (26.98 mm) and pitch 11.5 TPI.

1. Remove the casing over the connection and remove the plug.
2. Connect the hose.

NOTE:
The length of the hose should not exceed 60 cm and the outlet end should be placed at least 10 cm below the connection. Make sure the hose runs down without bends, otherwise there is a risk of leakage.

**NOTE:
If the product is emptied with a hose and is not going to be used for some time, remove the connection and clean the product. Collect any residual water in a suitable container

**

With pump function

Connect a hose with an inner diameter of 5 mm to the back of the product. The lift height when emptying should not more than 5 m.

1. Remove the casing over the connection and remove the plug.
2. Connect a hose with a diameter of 5 mm.

NOTE:
Connect the hose before starting the pump function.

MAINTENANCE

• Pull out the plug before maintenance and/or repairs.
• Pull out the plug if the product is not going to be used for some time.
• The filter and filter frame should be cleaned and dried regularly.
• Clean the product with a damp cloth. Do not pour or spray water or any other liquid on the product.
• Do not clean the product with solvent, such as benzene, petrol, or alcohol etc.
• Clean the water container and its cap regularly with a soft, damp cloth to  prevent mould in the product. Do not use abrasive detergent, or utensils that can scratch the surface.
• Clean the polypropylene strainer with water at least every other week. Do not use solvent or hot water.

TROUBLESHOOTING

FAQS

Why does less water collect in the water container during the winter?

• The air is drier when the outdoor temperature is lower. The dehumidification is therefore less  than during the summer. This is perfectly normal.
  Why does the product suddenly switch off, or not start?

• The water container could be full or not properly in place. Empty the water container and check that it is\ properly in place.

• Too high or low temperature or humidity. The product only dehumidifies at temperatures from 5 to 32°C an a humidity of 30 to 80%. The optimum temperature is 16 to 32°C.
  Why does warm air come out of the outlet?

• The product takes in room air and  dehumidifies it by cooling the temperature below dew point. The water in the air condenses and drops into the water container and the dehumidified air is warmed before it is released. This ensures quicker dehumidification and less consumption of energy. This is perfectly normal.

TROUBLESHOOTING

The troubleshooting guide is used to identify the causes of common problems and how they can be rectified. Contact the retailer if the problem cannot be rectified with the help of the troubleshooting guide.

__**Problem**

| __**Possible cause __**|

__**Action __**

---|---|---

The product does not start.

|

The plug is not plugged in.

|

Plug in the plug.

The water container is full or not properly in place.|

Empty the container and replace properly.

The ambient temperatures is less than 5°C or higher than 32°C.

|

Normal.

The product is not dehumidifying effectively.

|

The room temperature or humidity is too low.

|

Dehumidification is less when the humidity is lower.

Air inlet and/or air outlet blocked.

|

Unblock the air inlet and air outlet.

No air is blow out.

|

Air filter is blocked.

|

Clean the air filter according to the instructions.

Abnormal noise.

|

The product is tilted, or the surface is unstable.

|

Place the product on a level, stable surface.

Air filter is blocked.

| Clean the air filter according to the instructions.
Purling noise.|

This is caused by the flowing refrigerant and is completely normal.

Leaking water.

| The emptying hose has come loose.| Tighten the connection of the hose.

The emptying hose is blocked.

|

Unblock the emptying system and make sure the hose is not bent.

Freezing| The ambient temperature is too low, wait for defrosting.|

This is normal. The product has a defrosting function.

Error code on the
display

|

Significance

---|---

FL

| The water container is full.
E1|

The battery temperature sensor detects a fault.

E2

| The room temperature sensor detects a fault.
P1|

Normal. The product is in defrost mode.

CL

| Normal. The product is in drying mode.
LC|

Child lock activated.

DESCRIPTION

This is a SMART product that can be connected to existing WiFi and controlled via the app Smart Life, or with a voice assistant. Does not require a separate hub/router. You can control all SMART products in the app and use functions such as timer control, scheduling and automatised events.

SYSTEM REQUIREMENTS

WiFi router. iPhone, iPad (IOS 11.0 or higher) or Android (5.0 or higher).
Compatible with Google Assistant, Amazon\ Alexa and others.

USE

INSTALL APP

1. Scan the QR code to download the Smart Life app. Or search on App Store or Google Play.
2. Register your account with mobile number or email address. You will the receive a verification code via SMS or email. Enter
   the code in the app and select password. If you already have an account, log in with the mobile number or email address and password.
   

CONNECT PRODUCT

1. Check that the phone is connected to your WiFi and that the product is switched on.
2. Press + (add unit) on the start page.
3. Follow the guide to complete the connection.
4. The product is shown in the app when the connection is ready and you can now adjust the product via the app.
   

EU DECLARATION OF CONFORMITY

Jula Item number
023534
Model no.: YDA-50D/S3P-W
Jula AB, Box 363, SE-532 24 SKARA, SWEDEN
This declaration of conformity is issued under the sole responsibility of the manufacturer.
DEHUMIDIFIER EN
Conforms to the following directives, regulations and standards.

Directive/Regulation|

Harmonised standard

---|---

RED 2014/53/EU

|

EN 301489-V2.1.1, EN 301489-17 V3.1.1, EN 300328V2.1.1, EN 62311:2008, EN IEC 55014-1:2021, EN IEC 55014-2:2021, EN IEC 61000-3-2:2019+A1, EN 61000-3-3:2013+A2, EN 60335-2-40:2003+A11+A12+A1+A2+A13, EN 60335-1:2012+A11+A13+A1+A14+A2

RoHS 2011/65/EU + 2015/863

|

EN 50581:2012

This product was CE marked in year:
Signed for and on behalf of:
Skara 2022-06-21

Fredrik Bohman
BUSINESS AREA MANAGER

CUSTOMER SUPPORT

JULA AB
BOX 363, 532 24 SKARA, SWEDEN
WWW.JULA.COM

References

• Jula – products for home and garden

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>