CLAYPAKY CD3000 Sharpy Plus Aqua Moving Head Fixture Instruction Manual

CLAYPAKY CD3000 Sharpy Plus Aqua Moving Head Fixture

Product Information

Specifications

• Product Name: SHARPY PLUS CD3000
• Manufacturer: Claypaky
• Light Source: Internal light collimation system
• Control: DMX / Art-Net

Product Usage Instructions

Safety Information
It is important to read and follow the safety information provided by Claypaky. Ensure to keep the safety information accessible for reference.

Unpacking and Preparation
Upon unpacking, ensure all components are present according to the packing contents. Follow the instructions to unlock and set up the fixture properly.

Installation and Start-Up

Installing the Fixture
Install the projector on the floor with rubber feet, on a truss, ceiling, or wall. Always use the safety cable when not placed on the floor and securely fix it to the support structure.

Connecting to Mains Supply
Connect the power cable to the mains supply following the provided instructions and diagrams.

Connecting the Control Signal Line: DMX / Art-Net
Connect the control signal line according to the DMX or Art-Net protocol using the specified connectors.

Switching on the Fixture and Basic Setup
To switch on the projector, press the switch and follow the display instructions for resetting and setup. Use the control panel for programming and managing the projector menu.

FAQ

• Where can I find the safety information for the Sharpy Plus CD3000?
  The safety information can be found on the product’s official website at www.claypaky.com.

• How do I reset the effects on the projector?
  To reset the effects, switch on the projector and follow the instructions displayed on the screen for resetting.

SAFETY INFORMATION

IMPORTANT: Claypaky recommends you carefully read and keep the safety information on this product, also available in digital format at the following link: www.claypaky.com
Ref: [FIS01H: Safety information Sharpy Plus]

UNPACKING AND PREPARATION

Packing contents

PAN Mechanism Lock and Release (every 90°) – Fig. 2

TILT Mechanism Lock and Release (every 45°) – Fig. 3

INSTALLATION AND START-UP

Installing the fixture

Installing the projector – Fig. 4

• The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.
  WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request).

• This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.

Connecting to manis supply

Connecting and disconnecting power cable – Fig. 5

Connecting to the mains supply – Fig. 6

Connecting the control signal line: DMX / Art-Net
Connecting to the control signal line (DMX) – Fig. 7
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.

Switching on the fixture and basic SetUp

Switching on the projector – Fig. 8

• Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:

• On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the “Home” position (Pan 128 bit – Tilt 128 bit). The control panel (Fig. 8) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions: rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address.
• During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status. It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the key will be cancelled.

Reversal of the display – Fig. 9
To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.

Setting the projector starting address

• On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
• The address can also be set with the projector switched off.
• If there is no DMX input signal, the display will show “No signal”.

Functions of the buttons – Using the menu

USING THE MENU:

1. Press LEFT once – “Main Menu” appears on the display.
2. Use the UP and DOWN keys to select the menu to be used:
   • Setup (Setup Menu): To set the setting options.
   • Option (Option Menu): To set the operating options
   • Informations (Informations Menu): To read the counters, software version and other information.
   • Manual Control (Manual control Menu): To trigger the test and manual control functions.
   • Test (Test Menu): To check the proper functionning of effects
   • Advanced (Advanced Menu): Access to the “Advanced menu” is recommended for a trained technical personnel.
3. Press to display the first item in the selected menu.
4. Use the UP and DOWN keys to select the MENU items.

Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply. All that is needed is to press RIGHT to momentarily activate the display and thus access the settings. Once the required operations have been carried out, the display will switch off again after a wait time of 30 seconds.

MAINTENANCE

Opening the covers

Locking and releasing
Pan and Tilt movements – Refer to the instructions in the UNPACKING AND PREPARATION section.

Opening the head covers – Fig. 10.

Closing the head covers – Fig. 11.

Periodical cleaning – Fig. 12

• To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.).
• Use a soft cloth dampened with any detergent liquid for cleaning glass to remove the dirt from the reflectors, from the lenses and filters. It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations:
  • General cleaning of internal parts.
  • Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Claypaky.
  • General visual check of the internal components, cabling, mechanical parts, etc.
  • Electrical, photometric and functional checks; eventual repairs.
    NOTE: keep a careful cleaning of the ”CMY/colour filters assembly” to prevent rapid deterioration.

Effects module removal
Extraction of the effect modules – Fig. 13.
IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged.
Insertion of the effect modules: Repeat the operations indicated in Fig. 13, 14 and 15 in reverse order.

NOTE:

• Do not disconnect wiring harnesses when the fixtures is switched-on, to avoid to damage electronic boards.
• Do not switch-on the fixtures with wiring harness disconnected.

Cleaning of the filters – Fig. 14.

Lamp change – Fig 15.
Take the new lamp out of its package and insert in the fitting.
WARNING: do not touch the lamp’s envelope with bare hands. Should this happen, clean the bulb with a cloth soaked in alcohol and dry it with a clean, dry cloth.

Lamp regulation
To centre the lamp, turn the adjusting screw as shown in the figure.
WARNING: The lamp must be adjusted with the projector switched off. After adjusting, close the effects covers, switch on the projector and check that the adjustment has been correctly made. If necessary, switch off the projector, remove the effects covers and repeat lamp adjustment.
REMARK:

• Lifetime of the lamp will be influenced by the switching cycle.
• After a successful starting, attempt to keep the lamp burning for at least 15 minutes in order to complete the chemical cycle of the lamp to secure the lifetime.
• After switching-off the lamp wait at least 2 minutes before switching-on it again.

Rotating gobos

Bearing group replacement – Fig. 16

Gobo orientation – Fig. 17
The pictures shown the correct gobos orientation.

Replacing rotating gobos – Fig. 18

• Before use custom gobos contact Claypaky;
• The original gobos have a special coating designed specifically to resist to the high temperatures;
• The rotating gobo wheel only use dichroic glass gobos (it is not possible to use metal gobos);
• For more information contact Claypaky;

Battery removal – Fig. 19
This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force.

DIMENSIONS

Cause and solution of problems

ABOUT COMPANY

• www.claypaky.com
• Service support & Helpdesk: https://e-assist.tech

References

• Claypaky | Professional Lighting
• Claypaky - home

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>