Yibai ZIP 19True Wireless Earphone User Manual
- June 15, 2024
- Yibai
Table of Contents
Yibai ZIP 19True Wireless Earphone User Manual
Specifications
- Model: ZIP19
- Dynamic unit size: 10mm
- Earphone battery level: 30mAh*2
- Earphone single play time: 5 hours
- Charging case battery: 300mAh
- Cumulative playback time: about 20 hours
- Input Voltage/Current: 5V/0.3A
Product Diagram
The package box contains a charging case, a pair of wireless earphones and a charging cable
Operation
You can refer to this instruction to perform the following operations on the wireless earphones.
Turn on and Turn off
Turn on
- Method 1: When the charging case has remaining power, open the charging case and the earphones will automatically turn on;
- Method 2: Press and hold the touch area for 2 seconds in the off state, and the earphone will turn on
- Indicator light: The white light and red light are on for 1 second and then go out when the machine is turned off
- Voice reminder: After powering on, the voice prompt “Power on”
Turn off:
To turn off the earphones, press and hold the touch area of either earphone
for a few seconds until the indicator light goes off.
- Method 1: When there is remaining power in the charging box, the earphones will automatically shut down after being placed in the charging compartment;
- Method 2 : When not connected to the terminal device, the earphone will automatically shut down after 5 minutes or a long press on the touch area for 4 seconds ;
- Indicator light: the red light turns off after 2 seconds
- Voice reminder: Before shutting down, the voice prompts “Power off”
Pairing
Pairing includes the pairing between the left and right earphones and the connection between the earphones and the terminal device.
Pairing between left and right earphones:
The two earphones can be paired automatically after powering on. Before
pairing, the indicator light will flash alternately between red and white.
Once the pairing is successful, the white light will flash and you will hear a
prompt sound “DuDu”.
Connection to terminal equipment:
To connect the earphones to your Bluetooth-enabled device, follow these
steps:
- Make sure Bluetooth is turned on on your device.
- Turn on the earphones.
- Search for Bluetooth signals on your device.
- Select the corresponding earphone signal name.
- Select “Connect” to pair with the terminal device.
- Bluetooth on the end device turned on
- After the earphone is turned on, search for the Bluetooth signal on the terminal device , select the corresponding earphone signal name, and then select Connect to pair with the terminal device.
Earphone indicator light:
Before the connection is successful, the white light quickly flashes; After
the connection is completed, the indicator light goes out.
After the earphone successfully completes a connection with the terminal
device, the earphone will automatically find the terminal device that was
successfully connected last time when it is used again, and try to connect
with it.
The earphone indicator light will quickly flash white before the connection is successful, and it will go out once the connection is completed. After the earphones successfully connect to a terminal device, they will automatically try to connect with the same device when used again.
Play music or audiobooks:
To play or pause music or audiobooks, double-tap on any earbud. The
indicator light will not provide any prompt for this action.
Play / Pause
Double tap on any earbud to play or pause music
Indicator light: no prompt
Switch up and down:
To switch to the last song, press and hold the touch area of the left
earphone for 1 second.To switch to the next song, press and hold the touch
area of the right earphone for 1 second.
Last song: press the touch area of the left earphone for 1 second
Next song: press the touch area of the right earphone for 1 second Adjust
the volume
Increase volume: Operate the touch area of the right earphone in the way
of interval touch, each touch , the volume of the earphone will increase by 1
unit
Prompt “Dudu” at maximum volume
Decrease the volume:
Operate the touch area of the left earphone in the way of interval touch, each
touch , the volume of the earphone will increase by 1 unit. There is no prompt
tone at minimum volume. When using a single earphone, the volume cannot be
adjusted through the earphone.
Voice assistant on/off
Turn on the voice assistant: touch any earphone touch area 4 times Turn
off the voice assistant: touch the touch area of any earphone twice When using
the voice assistant, the indicator light has no prompt, and the prompt sound
comes from the terminal device
Calls
answering call
Touch any earphone touch area once.
Indicator light: When there is an incoming call, the white light flashes
quickly, and goes off after the call is connected The prompt tone comes from
the terminal device
End call
Touch any earphone touch area twice When the call ends, there is no indicator
light, and the voice prompt is “Du”
Reject call
Touch any earphone touch area twice When rejecting a call, there is no
indication on the indicator light, and the voice prompt is “Du”
Restore factory settings
After the earphone is powered on, when the terminal device is not connected,
click the touch area of the two earphones for five consecutive times, and the
red and white lights will light up for two seconds at the same time, and
return to the factory settings.
Charging the earphones or charging case earphone charging
When the charging case has remaining power, put it into the charging
compartment and close the cover to automatically charge
Indicator light: The red light of the earphone is always on, and it will
go out when fully charged
Earphone low battery reminder: the white light flashes twice every 30
seconds
Charging case charging
When charging the charging box, the red light is always on, but it goes out
when fully charged. Low battery level of charging box: The red light flashes 3
times within 1 second and then goes out (it prompts once every time the
headphones are inserted) After the headphones are placed in the charging box,
the green light will light up for 4 seconds and then turn off.
Temperature overheating reminder: The red light flashes 3 times every 2 seconds until the temperature returns to the set range
The main parameters
Precautions
- Try to use the minimum volume that meets the needs. Long-term high-volume use will cause permanent hearing damage.
- Please keep the device and accessories out of the reach of children, and children should use the device under adult supervision.
- Do not immerse the device in water for a long time. Avoid using this product while swimming, diving, diving or showering.
- Do not use this product in places with humidity, dust, or near magnetic fields, so as not to cause internal circuit failure.
- Avoid storing the earphones in an environment below -15°C or above 50°C.
- Avoid charging the earphone or charging case in an environment below 0°C.
- Do not place the earphones on windowsills, car dashboards and other places exposed to direct sunlight for a long time.
- Do not disassemble, modify the device, or insert foreign objects into the device, as these may cause damage to the device.
Adjust the volume:
To increase the volume, operate the touch area of the right earphone with
interval touches. Each touch will increase the volume by 1 unit. You will hear
a prompt sound “Dudu” when reaching the maximum volume.
Answering calls:
To answer an incoming call, touch any earphone touch area once. The white
indicator light will flash quickly when there is an incoming call and it will
go off after the call is connected. The prompt tone will come from the
terminal device.
End calls:
To end a call, touch any earphone touch area twice. There will be no
indicator light, and you will hear a voice prompt “Du” when the call ends.
Reject calls:
To reject an incoming call, touch any earphone touch area twice. There will
be no indication on the indicator light, and you will hear a voice prompt
“Du”.
Charging:
When charging the charging case, the red light will be always on until it
is fully charged, then the light will go out. When the charging case has a low
battery level, the red light will flash 3 times within 1 second and then go
out. This prompt will occur every time the headphones are inserted. After
placing the headphones in the charging case, the green light will light up for
4 seconds and then turn off. If the temperature of the earphones or charging
case exceeds the set range, the red light will flash 3 times every 2 seconds
until the temperature returns to normal.
Precautions:
FCC Requirement: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Frequently Asked Questions
How do I reset the earphones?
To reset the earphones, put them in the charging case and press and hold
the touch areas of both earphones for 10 seconds until you see the indicator
light flashing in red and white.
How do I check the battery level of the earphones?
You can check the battery level of the earphones by opening the charging
case while they are inside. The indicator lights of the earphones will
indicate their battery level.
Can I use only one earphone at a time?
Yes, you can use either the left or right earphones individually. Simply
take out the earphones you want to use from the charging case and follow the
pairing instructions.
Can I use the earphones while they are charging?
Yes, you can use the earphones while they are charging. However, please
note that charging may take longer if you are using them simultaneously.
How do I clean the earphones?
To clean the earphones, gently wipe them with a soft, dry cloth. Do not use
any liquid or cleaning agents as they may damage the earphones.
Welcome to ZIP19 Wireless Earphones!In order to let you understand ZIP19 more quickly , please read the following instructions carefully.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>