BOSCH GTA 2500 W Axial Glide Mitre Saw Instruction Manual

GCM 18V-305 GDC
Professional

GTA 2500 W Axial Glide Mitre Saw

Safety Instructions

WARNING
General Power Tool Safety Warnings Read all safety warnings, instructions, illustrations and specifictions provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/ or serious injury.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a  power tool. Distractions can cause you to lose control.
Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.
  There is an increased risk of electric shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of elec- tric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

• When operating a power tool outdoors, use an extension cord suitable for outdoor use.
  Use of a cord suitable
  for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
  Use of an RCD reduces the risk of electric shock.

Personal safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.
  Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal in- jury.

• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts.
  Loose clothes, jewellery or long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
  Use of dust collection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
  Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was de- signed.

• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories. Check for mis- alignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
  Use of the power tool for operations different from those intended could result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
  Battery tool use and care

• Recharge only with the charger specified by the manufacturer.
  A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

• Use power tools only with specifically designated battery packs.
  Use of any other battery packs may create a risk of injury and fire.

• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
  Liquid ejected from the battery may cause irritation or burns.

• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

• Do not expose a battery pack or tool to fire or excessive temperature.
  Exposure to fire or temperature above 130°C may cause explosion.

• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service of bat- tery packs should only be performed by the manufacturer or authorized service providers.

Safety Warnings for Mitre Saws

• Mitre saws are intended to cut wood or wood-like products, they cannot be used with abrasive cut-off wheels for cutting ferrous material such as bars, rods, studs, etc. Abrasive dust causes moving parts such as the lower guard to jam. Sparks from abrasive cutting will burn the lower guard, the kerf insert and other plastic parts.

• Use clamps to support the workpiece whenever possible. If supporting the workpiece by hand, you must always keep your hand at least 100 mm from either side of the saw blade. Do not use this saw to cut pieces that are too small to be securely clamped or held by hand.
  If your hand is placed too close to the saw blade, there is an increased risk of injury from blade contact.

• The workpiece must be stationary and clamped or held against both the fence and the table. Do not feed the workpiece into the blade or cut “freehand” in any way. Unrestrained or moving workpieces could be thrown at high speeds, causing injury.

• Push the saw through the workpiece. Do not pull the saw through the workpiece. To make a cut, raise the saw head and pull it out over the workpiece without cutting, start the motor, press the saw head down and push the saw through the workpiece. Cutting on the pull stroke is likely to cause the saw blade to climb on top of the workpiece and violently throw the blade assembly towards the operator.

• Never cross your hand over the intended line of cutting either in front or behind the saw blade. Supporting the workpiece “cross handed” i.e. holding the workpiece to the right of the saw blade with your left hand or vice versa is very dangerous.

• Do not reach behind the fence with either hand closer than 100 mm from either side of the saw blade, to remove wood scraps, or for any other reason while the blade is spinning. The proximity of the spinning saw blade to your hand may not be obvious and you may be seriously injured.

• Inspect your workpiece before cutting. If the workpiece is bowed or warped, clamp it with the outside bowed face toward the fence. Always make certain that there is no gap between the workpiece, fence and table along the line of the cut. Bent or warped workpieces can twist or shift and may cause binding on the spinning saw blade while cutting. There should be no nails or foreign objects in the workpiece.

• Do not use the saw until the table is clear of all tools, wood scraps, etc., except for the workpiece. Small debris or loose pieces of wood or other objects that con- tact the revolving blade can be thrown with high speed.

• Cut only one workpiece at a time. Stacked multiple  workpieces cannot be adequately clamped or braced and may bind on the blade or shift during cutting.

• Ensure the mitre saw is mounted or placed on a level, firm work surface before use. A level and firm work surface reduces the risk of the mitre saw becoming unstable.

• Plan your work. Every time you change the bevel or mitre angle setting, make sure the adjustable fence is set correctly to support the workpiece and will not interfere with the blade or the guarding system. Without turning the tool “ON” and with no workpiece on the table, move the saw blade through a complete simulated cut to assure there will be no interference or danger of cutting the fence.

• Provide adequate support such as table extensions, saw horses, etc. for a workpiece that is wider or longer than the table top. Workpieces longer or wider than the mitre saw table can tip if not securely supported.
  If the cut-off piece or workpiece tips, it can lift the lower guard or be thrown by the spinning blade.

• Do not use another person as a substitute for a table extension or as additional support. Unstable support for the workpiece can cause the blade to bind or the workpiece to shift during the cutting operation pulling you and the helper into the spinning blade.

• The cut-off piece must not be jammed or pressed by any means against the spinning saw blade. If confined, i.e. using length stops, the cut-off piece could get wedged against the blade and thrown violently.

• Always use a clamp or a fixture designed to properly support round material such as rods or tubing. Rods have a tendency to roll while being cut, causing the blade to “bite” and pull the work with your hand into the blade.

• Let the blade reach full speed before contacting the workpiece. This will reduce the risk of the workpiece being thrown.

• If the workpiece or blade becomes jammed, turn the mitre saw off. Wait for all moving parts to stop and disconnect the plug from the power source and/or remove the battery pack. Then work to free the jammed  material.
  Continued sawing with a jammed workpiece could cause loss of control or damage to the mitre saw.

• After finishing the cut, release the switch, hold the saw head down and wait for the blade to stop before removing the cut-off piece. Reaching with your hand near the coasting blade is dangerous.

• Hold the handle firmly when making an incomplete cut or when releasing the switch before the saw head is completely in the down position. The braking action of the saw may cause the saw head to be suddenly pulled downward, causing a risk of injury.

• Do not let go of the handle once the saw head has reached the lowest position. Always guide the saw head back to the top position by hand. There is a risk of injury if the saw head moves in an uncontrolled manner.

• Keep your work area clean. Material mixtures are particularly hazardous. Light metal dust may catch fire or ex- plode.

• Do not use dull, cracked, bent or damaged saw blades.
  Unsharpened or improperly set saw blades produce narrow kerf causing excessive friction, blade binding and kickback.

• Do not use saw blades made from high speed steel (HSS). Such saw blades can easily break.

• Always use saw blades with correct size and shape (diamond versus round) of arbour holes. Saw blades that do not match the mounting hardware of the saw will run off-centre, causing loss of control.

• Never remove cuttings, wood chips, etc. from the cutting area while the power tool is running. Always guide the tool arm back to the neutral position first and then switch the power tool off.

• Do not touch the saw blade after working before it has cooled. The saw blade becomes very hot while working.

• In case of damage and improper use of the battery, vapours may be emitted. The battery can set alight or explode. Ensure the area is well ventilated and seek medical attention should you experience any adverse effects. The vapours may irritate the respiratory system.

• Do not open the battery. There is a risk of short-circuiting.

• The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally.
  An internal short circuit may occur, causing the battery to burn, smoke, explode or overheat.

• Only use the battery in the manufacturer’s products.
  This is the only way in which you can protect the battery against dangerous overload.

Protect the battery against heat, e.g. against continuous intense sunlight, fire, dirt, water and moisture. There is a risk of explosion and short- circuiting.

• Never make warning signs on the machine unrecognisable.
• The power tool is delivered with a laser warning sign (see table: “Symbols and their meaning”).

Do not direct the laser beam at persons or animals and do not stare into the direct or reflected laser beam yourself. You could blind somebody, cause accidents or damage your eyes.

• Do not make any modifications to the laser equipment.
  The setting options described in these operating instructions can be used safely.

• Do not use the laser goggles (accessory) as protective goggles. The laser goggles make the laser beam easier to see; they do not protect you against laser radiation.

• Do not use the laser goggles (accessory) as sunglasses or while driving. The laser goggles do not provide full UV protection and impair your ability to see colours.

• Warning! If operating or adjustment devices other than those specified here are used or other procedures are carried out, this can lead to dangerous exposure to radiation.

• Do not replace the integrated laser with a laser of another type. A laser that is not compatible with this power tool could pose a risk to persons.

• Caution! When using the power tool with Bluetooth , a fault may occur in other devices and systems, aeroplanes and medical devices (e.g. pacemakers, hearing aids). Also, damage to people and animals in the immediate  vicinity cannot be completely excluded. Do not use the power tool with Bluetooth in the vicinity of medical devices, petrol stations, chemical plants, areas with a potentially explosive atmosphere or in blasting areas. Do not use the power tool with Bluetooth® in aircraft. Avoid using the product near your body for extended periods.
  The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Robert Bosch Power Tools GmbH is under license.

Symbols

Europe
The following symbols may be important for the operation of your power tool. Please take note of these symbols and their meaning. Correctly interpreting the symbols will help you to operate the power tool more effectively and safely.
Symbols and their meaning

| Class 1 Consumer Laser Product
---|---
| Keep hands away from the cutting area while the power tool is running. Contact with the saw blade can lead to injuries.
| Wear safety goggles.
| Wear a dust mask.
| Wear hearing protection. Exposure to noise can cause hearing loss.
| Danger area! Keep hands, fingers and arms away from this area.
| Keep your fingers away from the moving parts of the glide arm. There is a risk of fingers being crushed and severely in- jured.

Take note of the dimensions of the saw blade (saw blade diameter D, hole diameter d). The hole diameter d must match the tool spindle without play. If it is necessary to use reducers, ensure that the dimensions of the reducer are suitable for the base blade thickness and the saw blade hole diameter, as well as the tool spindle diameter. Wherever possible, use the reducers provided with the saw blade.
The saw blade diameter D must match the information specified on the symbol. See also: “Dimensions of suitable saw blades” in the “Technical Data” section.
Shows the rotational direction of the SDS bolt for tightening the saw blade (anticlockwise) nd for loosening the saw blade (clockwise).
Symbols and their meaning

| When transporting the power tool, hold it only at the locations indicated (recessed handles) or by the transport handle.
---|---
| Never carry the power tool using the handle of the glide arm.
| For bevel angles, you need to adjust the left/right fence extension or completely remove it.
| In combination with the ProCORE18V rechargeable batteries, the new high- performance motor offers a comparable performance to that of the motors of corded power
tools.
| Clamping handle open:
Bevel angles can be adjusted. Clamping handle closed: The set bevel angle of the glide arm is
locked.
| Indicates the individual steps for adjust- ing the bevel angle.
1. Loosen the clamping handle
2. Swivel the glide arm slightly to the left
3. Set the required bevel angle range using the rotary knob
| Setting the bevel angle ranges using the rotary knob:
| Saw blade inclination to the left (45° to 0°)
| Saw blade inclination to the right (0° to 45°)
| Entire swivel range of the glide arm (-47° to +47°)

Product Description and Specifications

Read all the safety and general instructions.
Failure to observe the safety and general in- structions may result in electric shock, fire and/or serious injury.
Please observe the illustrations at the beginning of this operating manual.
Intended Use
The power tool is intended as a stationary machine for making straight cuts in wood with and against the grain. It is possible to cut mitre angles of -52° to +60° and bevel angles of 47° (to the left) to 47° (to the right).
The power tool is designed with sufficient capacity for sawing hardwood and softwood as well as chipboard and fibreboard.
When using appropriate saw blades, sawing aluminium profiles and plastic is also possible.
Low Energy Module GCY 42 inserted, power tool data and settings can be transferred between the With the Bluetooth® power tool and a mobile device by means of Bluetooth wireless technology.
Europe This product is a consumer laser product in accordance with EN 50689.
Product features
The numbering of the product features refers to the diagram of the power tool on the graphics page.

1. Handle
2. Lock-off function for on/off switch
3. User Interface
4. Protective guard
5. Retracting blade guard
6. Adjustable fence
7. Fence
8. Saw table extension
9. Mounting holes
10. Insert plate
11. Locking clamp
12. Locking knob for various mitre angles
13. Mitre pre-setting lever
14. Clamping handle for various bevel angles
15. Detents for standard mitre angles
16. Recessed handles
17. Hex key (6 mm/4 mm)
18. Hex key (2 mm)
19. Screw clamp
20. Guide roller
21. Angle indicator for right-hand bevel angle range (0° to 47°)
22. Chip deflector
23. SDS bolt
24. Chip ejector
25. Glide mechanism clamping lever
26. Dust extraction adapter
27. Depth stop adjusting screw
28. Depth stop
29. Laser warning label
30. Laser protection cap
31. Cover for GCY 42 Bluetooth ® Low Energy Module
32. Rechargeable battery
33. Rechargeable battery release button
34. Glide arm
35. Transport safety lock
36. Scale for bevel angle
37. Angle indicator for left-hand bevel angle range (47° to 0°)
38. Adjustment knob for 22.5° bevel angle
39. Locking screw for length stop
40. Length stop
41.  Scale for mitre angles
42. Saw table
43. Rotary knob for adjusting the bevel angle range
44. Saw blade
45. Laser beam outlet aperture
46. Battery charge indicator (user interface)
47. ECO mode indicator (user interface)
48. Speed preselection button (user interface)
49. Speed setting/mode indicator (user interface)
50. Smartphone symbol (user interface)
51. Power tool status indicator (user interface)
52. Temperature indicator (user interface)
53. Spindle lock
54. Hex socket screw for mounting the saw blade
55. Clamping flange
56. Inner clamping flange
57. Clamping lever of the saw table extension
58. Locking screw for the adjustable fence
59. Damper
60. Set screws for damping
61. Holes for screw clamp
62. Wing bolt
63. Threaded rod
64. Angle indicator for mitre angles
65. On/off switch
66. Screws for insert plate
67. Clamping screw for length stop
68. Set screws for positioning the laser (flush align- ment)
69. Set screws for 0° basic setting (bevel angle)
70. Set screw for 45° basic setting (left-hand bevel angle)
71. Set screw for 45° basic setting (right-hand bevel angle)
72.  Set screws for mitre angle scale
73. Screw for mitre angle indicator
74. Set screw for adjusting the clamping force of the clamping handle for any bevel angle

a) This accessory is not part of the standard scope of delivery.
Technical Data
Europe

ProCORE18V…
Recommended battery chargers| | GAL 18…
GAX 18…
GAL 36…| GAL 18…
GAX 18…
GAL 36…

Data transfer

A) Measured at 20–25 °C with rechargeable battery ProCORE18V 8.0Ah
B) Depends on battery in use
C) Limited performance at temperatures < 0 °C
D) The mobile devices must be compatible with Bluetooth® Low Energy devices (version 4.2) and support the Generic Access Profile (GAP).
E) The signal range may vary greatly depending on external conditions, including the receiving device used. The Bluetooth® range may be signi- ficantly weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases, etc.).
Permitted workpiece dimensions (maximum/minimum): (see “Permissible workpiece dimensions”, page 47) Values can vary depending on the product, scope of application and environmental conditions. To find out more, visit www.bosch- professional.com/wac.
Noise Information
Noise emission values determined according to EN IEC 62841-3-9.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 93 dB(A); sound power level 106 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
The noise emission value given in these instructions has been measured in accordance with a standardised measuring procedure and may be used to compare power tools. It may also be used for a preliminary estimation of noise emissions.
The noise emission value given represents the main applications of the power tool. However, if the power tool is used for other applications, with different application tools or is poorly maintained, the noise emission value may differ. This may significantly increase noise emissions over the total working period.
To estimate noise emissions accurately, the times when the  tool is switched off, or when it is running but not actually being used, should also be taken into account. This may significantly reduce noise emissions over the total working period.
Rechargeable battery
Bosch sells some cordless power tools without a rechargeable battery. You can tell whether a rechargeable battery is included with the power tool by looking at the packaging.
Charging the battery

• Use only the chargers listed in the technical data. Only these chargers are matched to the lithium-ion battery of your power tool.
  Note: Lithium-ion rechargeable batteries are supplied par- tially charged according to international transport regulations.
  To ensure full rechargeable battery capacity, fully charge the rechargeable battery before using your tool for the first time.

Inserting the Battery
Push the charged battery into the battery holder until it clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery release button and pull the battery out. Do not use force to do this.
The rechargeable battery has two locking levels to prevent the battery from falling out if the battery release button is pressed unintentionally. The rechargeable battery is held in place by a spring when fitted in the power tool.
Battery charge indicator
Note: Not all battery types have a battery charge indicator. The green LEDs on the battery charge indicator indicate the state of charge of the battery. For safety reasons, it is only possible to check the state of charge when the power tool is not in operation.
Press the button for the battery charge indicator  show the state of charge. This is also possible when the battery is removed.
If no LED lights up after pressing the button for the battery charge indicator, then the battery is defective and must be replaced.
The state of charge of the battery is also displayed on the user interface Status indications.
Battery model GBA 18V…

Battery model ProCORE18V…

Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to 50 °C. Do not leave the battery in your car in the summer, for example.
Occasionally clean the ventilation slots on the battery using a soft brush that is clean and dry.
A significantly reduced operating time after charging indicates that the battery has deteriorated and must be replaced. Follow the instructions on correct disposal.

Assembly

• Before carrying out any work on the power tool (e.g. maintenance, tool change etc.), remove the battery from the power tool. There is risk of injury from unintentionally pressing the on/off switch.

Items Included
See the list of items included at the start of the operating manual.
Check to ensure that all the parts listed below have been supplied before using the power tool for the first time:

• Sliding mitre saw with fitted saw blade (44)
• Locking knob (12)
• Hex key (17)
• Hex key (18)
• Screw clamp (19)
• SDS bolt (23)
• Dust bag

Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that all protective devices or slightly damaged parts are working perfectly and according to specifications. Check that the moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fitted correctly and all the conditions necessary to ensure smooth operation must be met.
If the protective devices or any parts become damaged, you must have them properly repaired or replaced by an authorised service centre.
Extra tools required (not included in the delivery):

• Cross-headed screwdriver
• Open-ended spanner (size: 8 mm)
• Ring spanner, open-ended spanner or socket spanner (sizes: 10 mm and 17 mm)

Activating the Bluetooth® Low Energy Module GCY 42
Read the corresponding operating instructions for information about the Bluetooth®
Low Energy Module GCY 42.
Activating the Button Cell

• To open the cover (31), press on it with two fingers and turn them anticlockwise.
  Using unsuitable objects to open it (such as screw- drivers or coins) can damage the electronics or the cover.

• Remove the insulation between the coin cell and the Bluetooth® Low Energy Module GCY 42.

• Close the cover (31) to prevent dirt from getting in (insert the cover, press on it gently with two fingers and turn them clockwise).

Fitting individual components

• Carefully remove all parts included in the delivery from their packaging.

• Remove all packing material from the power tool and the accessories provided.
  Fitting the locking knob (see figure a)

• Screw the locking knob (12) into the corresponding hole above the lever (13).

• Always tighten the locking knob (12) firmly before sawing. Otherwise the saw blade can become wedged in the workpiece.

Stationary or flexible mounting

• To ensure safe handling, the power tool must be mounted on a flat, stable work surface (e.g. work bench) before use.

Mounting on a work surface (see figure b1)

• Use suitable screw fasteners to secure the power tool to the work surface. The holes (9) are used for this purpose.
• Firmly clamp the base of the power tool to the work sur- face with commercially available screw clamps.

Mounting on a Bosch saw stand (see figure b2)
(GTA 2500 W, GTA 2500 Compact, GTA 2600, GTA 3800)
With the height-adjustable legs, Bosch GTA saw stands provide firm support for the power tool on any surface. The workpiece supports of the saw stand are used for underlaying long workpieces.

• Read all the warnings and instructions included with the saw stand. Failure to observe the warnings and follow instructions may result in electric shock, fire and/or serious injury.
• Assemble the saw stand properly before mounting the power tool. Correct assembly is important to prevent the risk of collapsing.
  – Mount the power tool on the saw stand in the transport position.

Dust/Chip Extraction
The dust from materials such as lead paint, some types of wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reactions and/or cause respiratory illnesses in the user or in people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as carcinogenic, especially in conjunction with wood treatment additives (chromate, wood preservative). Materials containing asbestos may only be machined by specialists.

• Use a dust extraction system that is suitable for the material wherever possible.
• Provide good ventilation at the workplace.
• It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can easily ignite.
The dust/chip extraction system can be blocked by dust, chips or fragments of the workpiece.
– Switch the power tool off and remove the battery.
– Wait until the saw blade has come to a complete stop.
– Determine the cause of the blockage and eliminate it.
External Dust Extraction
You can also attach a dust extraction hose (35 mm diameter) to the extraction adapter (26) for extraction.
– Connect the dust extraction hose to the extraction adapter (26).
The dust extractor must be suitable for the material being worked.
When extracting dry dust that is especially detrimental to health or carcinogenic, use a special dust extractor.
Cleaning the dust extraction adapter
To ensure optimum extraction, the dust extraction adapter (26) must be cleaned regularly.

• Pull the dust extraction adapter (26) off the chip ejector (24) with a twisting motion.
• Remove workpiece fragments and chippings.
• Reattach the dust extraction adapter to the chip ejector with a twisting motion until it engages above the chip ejector holding ring.

Changing the Saw Blade

• Before carrying out any work on the power tool (e.g. maintenance, tool change etc.), remove the battery from the power tool. There is risk of injury from unintentionally pressing the on/off switch.
• Wear protective gloves when fitting the saw blade. There is a risk of injury when touching the saw blade. Only use saw blades that have a maximum permitted speed higher than the no-load speed of the power tool.
  Only use saw blades that match the specifications given in this operating manual and that have been tested and marked in accordance with EN 847-1.
  Only use saw blades that are recommended by the power tool manufacturer and are suitable for use on the material you want to saw. This will prevent the saw teeth overheating when sawing.

Assembly with hex socket screw (see figures c1−c4) Removing the Saw Blade

• Bring the power tool into the work position.
• Swivel the retracting blade guard (5) to the back and hold it in this position.
• Turn the hex socket screw (54) with the hex key (4 mm) (17) and at the same time push the spindle lock (53) until it engages.
• Keep holding the spindle lock (53) and loosen the hex socket screw (54) by turning it clockwise (left-hand thread).
• Remove the clamping flange (55).
• Remove the saw blade (44).
•  Slowly push the retracting blade guard back down.

Fitting the saw blade
u When fitting the saw blade, make sure that the cutting direction of the teeth (arrow direction on the saw blade) matches the direction of the arrow on the protective guard.
If required, clean all the parts you want to fit before installing them.

• Swivel the retracting blade guard (5) to the back and hold it in this position.
• Place the new saw blade on the inner clamping flange (56).
• Fit the clamping flange (55) and the hex socket screw (54). Press the spindle lock (53) until it engages and tighten the hex socket screw by turning it anticlockwise.
• Slowly push the retracting blade guard back down.

Assembly with SDS bolt (see figure d)
u For bevel cuts when using the SDS bolt (23), before sawing, first make sure that the SDS bolt cannot come into contact with the surface of the workpiece at any time by making a suitable adjustment to the depth stop (28). This prevents damage to the SDS bolt and/or the workpiece.
Removing the saw blade

• Bring the power tool into the work position.
• Swivel the retracting blade guard (5) to the back and hold it in this position.
• Turn the SDS bolt (23) while pressing the spindle lock (53) until it engages.
• Press and hold the spindle lock (53) and unscrew the SDS bolt (23) by turning it clockwise (left-hand thread).
• Remove the clamping flange (55).
• Remove the saw blade (44).
• Slowly push the retracting blade guard back down.

If required, clean all the parts you want to fit before installing them.

• Swivel the retracting blade guard (5) to the back and hold it in this position.
• Place the new saw blade on the inner clamping flange (56).
• Attach the clamping flange (55) and the SDS bolt (23). Press the spindle lock (53) until it engages and tighten he SDS bolt by turning it anticlockwise.
• Slowly push the retracting blade guard back down.

Operation

• Before carrying out any work on the power tool (e.g. maintenance, tool change etc.), remove the battery from the power tool. There is risk of injury from unintentionally pressing the on/off switch.
  Transport Safety Lock (see figure A)
  The transport safety lock (35) makes it easier to handle the power tool when transporting it to various working locations.
  Unlocking the Power Tool (Work Position)

•  Press the glide arm (34) down slightly by the handle (1) to release the transport safety lock (35).

•  Pull the transport safety lock (35) all the way out.

• Slowly guide the glide arm (34) upwards.

Locking the Power Tool (Transport Position)

• Slide the glide arm (34) all the way back and secure it in this position.
• Guide the glide arm downwards until you can press the transport safety lock (35) all the way in.
  Further information: (see “Transport (see figure Z)”, page 49)

Locking the Glide Arm
The glide mechanism of the glide arm (34) can be locked with the clamping lever (25). The glide arm can be placed in two positions:

• Glide arm pushed all the way back (for cross cuts)
• Glide arm pulled all the way forward (for a compact transport position)

Unlocking the Glide Arm (see figure B1)
After unlocking the glide arm (34), the whole gliding mechanism is ready for operation.

• Press the clamping lever (25) all the way down.
• The clamping wedge of the clamping lever releases the two articulated parts at the bottom of the glide arm.

Securing the Glide Arm (see figure B2)
Glide arm pushed all the way back:

• Push the glide arm (34) all the way back.

• The two articulated parts at the top of the glide arm are now upright and closed.

• Pull the clamping lever (25) upwards until the clamping wedge is positioned between the two articulated parts at the bottom of the glide arm.

• This locks the glide arm (34), which is pushed all the way back.
  Glide arm pulled all the way forward:

• Pull the glide arm (34) all the way forward.

• The glide mechanism is now completely extended.

• Pull the clamping lever (25) upwards until the clamping wedge is positioned between the two articulated parts atthe bottom of the glide arm.

• This locks the glide arm (34), which is pulled all the way forward.

Preparing for operation
Extending the Saw Table (see figure C)
The free end of long workpieces must have something placed underneath it or be supported.
The saw table can be extended left and right using the saw table extensions (8).

• Push the clamping lever (57) inwards.
• Pull out the saw table extension (8) to the required length (maximum 250 mm).
• To lock the saw table extension in place, push the clamping lever (57) back out.

Moving the fence (see figures D–E)
When sawing mitre and/or bevel angles, you have to pull the left-hand or right-hand adjustable fence (6) outwards depending on the cutting direction, or remove it completely.

Bevel angle| Mitre angle|
---|---|---
0°-47° (left)| ‘≤ 44° (right/left)| – Loosen the locking screw (58).
– Pull the left-hand adjustable fence (6) all the way out.
0°–47° (left)| < 44° (right/left)| – Loosen the locking screw (58).
– Pull the left-hand adjustable fence (6) all the way out.
0°-47° (left)| > 45° (right/left)| – Loosen the locking screw (58).
– Pull the left-hand adjustable fence (6) all the way out.
– Lift the adjustable fence upwards and out of the way.
– Remove the locking screw (58).
0°–47° (right)| ≥ 45° (right/left)

Adjusting the damping of the glide arm (see figure F)
The glide mechanism of the glide arm (34) is preset at the factory and is not damped when the power tool is delivered.
The damping of the glide mechanism can be adjusted using the damper (59):
Hard – for more controlled work movements;
Soft

• for fast saw cuts.

• For softer damping, loosen the two set screws (60) using the hex key (4 mm) (17)

• or

• tighten the two set screws (60) for harder damping.
  Clamping the workpiece (see figure G)
  To ensure maximum safety while working, the workpiece must always be firmly clamped.
  Do not saw workpieces that are too small to clamp firmly.

• Press the workpiece firmly against the fences (7) and (6).

• Insert the supplied screw clamp (19) into one of the cor- responding holes (61).

• Loosen the wing bolt (61) and adjust the screw clamp to the workpiece. Tighten the wing bolt again.

• Tighten the threaded rod (63) to fix the workpiece in place.
  Releasing the workpiece

• To loosen the screw clamp, turn the threaded rod (63) anticlockwise.

Adjusting the Mitre Angle
Setting Standard Mitre Angles (see figure H) For quick and precise setting of commonly used mitre angles, detents (15) are provided on the saw table:

• Loosen the locking knob (12) if it is tightened.
• Pull the lever (13) and rotate the saw table (42) left or right to the required detent.
• Release the lever again. The lever must be felt to engage in the detent.
• Retighten the locking knob (12).

Setting Any Mitre Angle (see figure I)
The mitre angle can be set between 52° (left side) and 60° (right side).

• Loosen the locking knob (12) if it is tightened.

• Pull the lever (13) and at the same time press the locking clamp (11) until this clicks into the slot provided for it.
  This means the saw table can now move freely.

• Turn the saw table (42) left or right by the locking knob until the angle indicator (64) shows the required mitre angle.

• Retighten the locking knob (12).

• To loosen the lever (13) again (for setting standard mitre angles), pull the lever upwards.
  The locking clamp (11) springs back into its original position and the lever (13) can click back into the detents (15).

Adjusting Bevel Angles
The bevel angle can be set between 47° (left side) and 47° (right side).
For quick and precise setting of frequently used bevel angles, stops have been provided for the angles 0°, 22.5°, 45° and 47°.
Setting the Left-hand Bevel Angle range (45° to 0°)

• Pull the left-hand adjustable fence (6) all the way out.
• Loosen the clamping handle (14).
• Use the handle (1) to swivel the glide arm (34) to the left until the angle indicator (37) shows the required bevel angle.
• Hold the glide arm (34) in this position and retighten the clamping handle (14).
  The clamping force of the clamping handle must hold the glide arm securely in place at any bevel angle.

Setting the Right-hand Bevel Angle Range (0° to 45°) (see figure J)

• Pull the right-hand adjustable fence (6) all the way out.
• Loosen the clamping handle (14).
• Use the handle (1) to tilt the glide arm (34) slightly to the left from the 0° position and turn the rotary knob (43) until the required bevel angle range is shown.
• Use the handle (1) to swivel the glide arm (34) to the right until the angle indicator (21) shows the required bevel angle.
• Hold the glide arm (34) in this position and retighten the clamping handle (14).
  The clamping force of the clamping handle must hold the glide arm securely in place at any bevel angle.

Setting the Standard 0° bevel angle
**– Swivel the glide arm (34) from the right to the 0° position.
To enable the standard 0° bevel angle to be reset easily, the rotary knob (43) engages in the left- hand bevel angle range.
Setting the entire bevel angle range (–47° to +47°)**

• Pull both adjustable fences (6) all the way out.
•  Loosen the clamping handle (14).
• Use the handle (1) to tilt the glide arm (34) slightly to the left from the 0° position and turn the rotary knob (43) until the required bevel angle range is shown.
• Use the handle (1) to swivel the glide arm (34) to the left or right until the angle indicator (37) or (21) shows the required bevel angle.
• Hold the glide arm (34) in this position and retighten the clamping handle (14).
  The clamping force of the clamping handle must hold the glide arm securely in place at any bevel angle.

Setting the Standard 22.5° Bevel Angle (see figure K)
Pull the adjustment knob (38) all the way out and turn it 90°.
Then use the handle (1) to swivel the glide arm (34) until you hear the glide arm engage.
Start-up
Inserting the Battery

• Use only original Bosch lithium-ion batteries with the voltage stated on the type plate of your power tool.
  Using other batteries can lead to injuries and pose a fire hazard.
  – Push the charged battery (32) into the battery bay of the power tool until the battery is securely locked. Switching on (see figure L)
  – To switch on the power tool, first slide the lock-off button (2) to the middle and then press and hold the on/ off switch (65).
  Note: For safety reasons, the on/off switch (65) cannot be locked; it must remain pressed during the entire operation. Switching off
  – To switch off, release the on/off switch (65).

ECO mode
If the power tool is operated in the energy-saving ECO mode, the battery life may be up to 20% longer.
If the ECO mode is active, the symbol E is shown on the speed setting/mode indicator (49). In addition, the ECO mode indicator (47) lights up.
User interface
The user interface (3) is used to preselect the speed and to indicate the status of the power tool.
Speed preselection
An ECO mode and three speed settings are preset.
You can use the button for speed preselection (48) to preselect the required speed, even during operation.

Status indications

Battery charge indicator (user interface) (46)| Meaning/cause| Solution
---|---|---
Green (2 to 5 bars)| Battery charged| –
Yellow (1 bar)| Battery almost empty| Replace or charge battery soon
Red (1 bar)| Battery empty| Replace or charge battery
Temperature indicator (52)| Meaning/cause| Solution
---|---|---
Yellow| Critical temperature has been reached (motor, electronics, battery)| Run the power tool at no load and allow it to cool down
Temperature indicator| Meaning/cause| Solution
---|---|---
(52) Red| Power tool is overheated and will switch off| Leave the power tool to cool down
Power tool status indicator (51)| Meaning/cause| Solution
---|---|---
Green| Status OK| –
Yellow| Critical temperature has been reached or bat- tery is almost empty| Run the power tool at no load and allow it to cool down, or replace or charge the battery soon
Red| Power tool is overheated or battery is empty| Allow the power tool to cool down, or replace or charge the battery
Flashing red| Restart protection is triggered| Turn the power tool off and on again; if necessary, remove the battery and reinsert it.

Connectivity functions
In conjunction with the Bluetooth® Low Energy Module GCY 42, the following connectivity functions are available for the power tool:

• Registration and personalisation
• Status check, output of warning messages
• General information and settings
• Management
• Setting the speed levels

Read the corresponding operating instructions for informa- tion about the Bluetooth® Low Energy Module GCY 42. Further information can be found under the Power tool status display on a mobile device if it is connected via Bluetooth® wireless technology.

Practical advice
General sawing instructions

• Always tighten the locking knob (12) and the clamping handle (14) firmly before sawing.
  Otherwise the saw blade can become wedged in the workpiece.

• Always tighten the locking knob (12) and the clamping lever  firmly before sawing. Otherwise the saw blade can become wedged in the workpiece.

• For all cuts, it must first be ensured that the saw blade at no time can come in contact with the fence, screw clamps or other machine parts. Remove any mounted auxiliary stops or adjust them accordingly.

• With the Bluetooth® Low Energy Module GCY 42, the power tool is equipped with a radio interface. Local operating restrictions, e.g. in aircraft or hospitals, must be observed.

• In areas in which the Bluetooth® wireless technology must not be used, the Bluetooth® Low Energy Module GCY 42 and the coin cell must be removed.

The free end of long and heavy workpieces must have something placed underneath it or be supported.
Do not saw warped/bent workpieces. The workpiece must always have a straight edge to face against the fence.
Only saw materials which are permitted within the scope of the intended use.
Position of the operator (see figure N)

• Do not stand in line with the saw blade in front of the power tool. Always stand to the side of the saw blade. This protects your body against possible kickback.
  – Keep hands, fingers and arms away from the rotating saw blade.
  – Do not reach one hand across the other when in front of the tool arm.

Replacing insert plates (see figure O)
The insert plates (10) can become worn after prolonged use of the power tool.
Replace faulty insert plates.

• Bring the power tool into the work position.
• Loosen the screws (66) using the hex key (18) and remove the old insert plates.
• Insert the new right-hand insert plate.
• Screw the insert plate as far as possible to the right with the screws (66) so that the saw blade does not come into contact with the insert plate over the entire length of the possible slide motion.
• Repeat the work steps in the same manner for the new left-hand insert plate.

Permissible workpiece dimensions

45 x 400
120 x 200
180 x 40
45° (left)| 0°| 104 x 240
180 x 20
0° 0°| 45° (left)| 60 x 341
0°| 45° (left)| 40 x 341
45° 45°| 45° (right)| 60 x 240
45°| 45° (right)| 40 x 240

A) With horizontal spacer (height x width: 60 mm x 400 mm)
B) With vertical spacer (height x width: 72 mm x 50 mm)
Minimum workpiece dimensions (= all workpieces that can be secured left or right of the saw blade using the supplied screw clamp (19)): 160 mm x 35 mm (length x width) Maximum cutting depth (0°/0°): 120 mm
Sawing
Sawing without slide movement (cutting off) (see figure P)

• Slide the glide arm (34) all the way back and secure it in this position.
  Make sure that the depth stop (28) is pressed all the way in and that the adjusting screw (27) fits through the recess without touching the depth stop when moving the glide arm.

• Firmly clamp the workpiece as appropriate for its dimen- sions.

•  Set the required mitre and/or bevel angle as necessary.

• Switch on the power tool.

• Slowly guide the glide arm (34) downwards using the handle (1).

•  Saw through the workpiece applying uniform feed.

• Switch off the power tool and wait until the saw blade has come to a complete stop.

• Slowly guide the glide arm (34) upwards.

Sawing with Slide Movement (see figure Q)

• Maintain a firm grip on the handle before switching the power tool on and during the entire sawing process.
  Ensure that the movement of the glide arm is controlled during sawing.
  The glide arm is very easy to move and a moment of inattention could result in serious injury.
  – Unlock the glide arm (34).
  Check if the complete glide mechanism is operative by sliding the glide arm (34) back and forth.
  – Firmly clamp the workpiece as appropriate for its dimensions.
  – Set the required mitre and/or bevel angle as necessary.
  – Pull the glide arm (34) away from the fence (7) by the handle (1) until the saw blade is in front of the workpiece.
  – Switch on the power tool.
  – Slowly guide the glide arm (34) downwards using the handle (1).
  – Now push the glide arm (34) towards the fence (7) and saw through the workpiece with uniform feed.
  – Switch off the power tool and wait until the saw blade has come to a complete stop.
  – Slowly guide the glide arm (34) upwards.

Sawing workpieces of the same length (see figure R)
The length stop (40) (accessory) can be used for easily sawing workpieces of the same length.
The length stop can be mounted on either side of the saw table extension (8).

• Loosen the locking screw (39) and move the length stop (40) over the clamping screw (67).
• Re-tighten the locking screw (39).
•  Set the saw table extension (8) to the required length.

Adjusting the Depth Stop (Sawing the Groove) (see figure S)
The depth stop needs to be adjusted if you wish to saw a groove or use a spacer.

• Swivel the depth stop (28) outwards.
• Use the handle (1) to swivel the glide arm (34) into the required position.
• Turn the adjusting screw (27) until the end of the screw touches the depth stop (28).
• Slowly guide the glide arm (34) upwards.

Special workpieces
When sawing curved or round workpieces, these must be especially secured against slipping. At the cutting line, there should be no gap between the workpiece, fence and saw table.
If necessary, you will need to manufacture special fixtures.
Working on mouldings
Mouldings can be sawn in two different ways:

Furthermore, you can cut with or without the slide movement depending on the width of the moulding.
Always check the set mitre and/or bevel angle first by making trial cuts in scrap wood.
Checking and Adjusting the Basic Settings
To ensure precise cuts, the basic settings of the power tool must be checked and adjusted as necessary after intensive use.
Experience and suitable special tools are required for this. A Bosch after- sales service point will handle this work quickly and reliably.
Adjusting the laser
Note: To test the laser function, the power tool must be connected to the power supply.

• While adjusting the laser (e.g. when moving the tool arm), never activate the on/off switch. Starting the power tool accidentally can lead to injuries.
  – Bring the power tool into the work position.
  – Turn the saw table (42) to the 0° detent (15). The lever (13) must be felt to engage in the detent.
  Checking (see figure T1)
  – Draw a straight cutting line on the workpiece.
  – Slowly guide the glide arm (34) downwards using the handle (1).
  – Position the workpiece so that the teeth of the saw blade line up with the cutting line.
  – Hold the workpiece in this position and slowly guide the glide arm upwards.
  – Clamp the workpiece.
  – Switch on the laser beams with the switch .
  The laser beams must be the same distance away (left and right) from the cutting line marked on the workpiece along their entire length, even when lowering the glide arm.

Setting (see figure T2)

1. Adjusting the right-hand laser beam:
   – Turn the right-hand set screw (68) using the hex key (18) until the entire length of the right-hand laser beam is flush with the cutting line marked on the workpiece.
   This also moves the left-hand laser beam.
   One rotation anticlockwise moves the laser beam from left to right; one rotation clockwise moves the laser beam from right to left.

2.  Adjusting the left-hand laser beam:
   – Turn the left-hand set screw (68) using the hex key (18) until the left-hand laser beam is the same distance away from the cutting line marked on the workpiece as the right-hand laser beam.
   One rotation anticlockwise moves the laser beam from left to right; one rotation clockwise moves the laser beam from right to left.
   Setting the Standard 0° Bevel Angle
   – Bring the power tool into the transport position.
   – Turn the saw table (42) to the 0° detent (15). The lever (13) must be felt to engage in the detent.

Checking (see figure U1)

• Set an angle gauge to 90° and place it on the saw table (42).
• The leg of the angle gauge must be flush with the saw blade (44) along its entire length. Setting (see figure U2)
• Loosen the clamping handle (14).
• Loosen the two set screws (69) (by at least one turn) us- ing a socket spanner (10 mm).
• Loosen the set screw (71) (by approx. three turns) using the hex key (4 mm) (17).
• Tighten or loosen the set screw (70) using the hex key (4 mm) (17) until the leg of the angle gauge is flush with the saw blade along its entire length.
• Retighten the clamping handle (14). Then tighten the set screw (71) followed by the set screws (69).
  If the angle indicators (37) and (21) are not in line with the 0° marks on the scale (36) following adjustment, loosen the fastening screws on the angle indicators using a crossheaded screwdriver and align the angle indicators with the 0° marks.

Setting the Standard 45° Mitre Angle (left)

• Bring the power tool into the work position.
• Turn the saw table (42) to the 0° detent (15). The lever 13) must be felt to engage in the detent.
• Pull the left-hand adjustable fence (6) all the way out.
• Loosen the clamping handle (14) and swivel the glide arm to the left stop (45°) by the handle (1).

Checking (see figure V1)

• Set an angle gauge to 45° and place it on the saw table (42).
  The leg of the angle gauge must be flush with the saw blade (44) along its entire length.
  Setting (see figure V2)

• Tighten or loosen the set screw (72) using an open-ended spanner (8 mm) until the leg of the angle gauge is flush with the saw blade along its entire length.

• Retighten the clamping handle (14).
  If the angle indicators (37) and (21) are not in line with the 45° marks on the scale (36) following adjustment, first check the 0° setting for the bevel angle and the angle indicat- ors once more. Then repeat the adjustment of the 45° bevel angle.

Setting the Standard 45° Mitre Angle (right)

• Bring the power tool into the work position.
• Turn the saw table (42) to the 0° detent (15). The lever (13) must be felt to engage in the detent.
• Pull the right-hand adjustable fence (6) all the way out.
• Loosen the clamping handle (14).
• Use the handle (1) to tilt the glide arm slightly to the left from the 0° position and turn the rotary knob (43) until the right-hand bevel angle range is shown.

Aligning the scale for mitre angles

• Bring the power tool into the work position.
• Turn the saw table (42) to the 0° detent (15). The lever (13) must be felt to engage in the detent. Checking (see figure X1)
• Set an angle gauge to 90° and position it between the fence (7) and the saw blade (44) on the saw table (42). The leg of the angle gauge must be flush with the saw blade (44) along its entire length.

Setting (see figure X2)

• Loosen all four set screws (74) using the hex key (4 mm) (17) and turn the saw table (42) together with the scale (41) until the leg of the angle gauge is flush with the saw blade along its entire length.
•  Re-tighten the screws again.
  If the angle indicator (64) is not aligned with the 0° mark on the scale (41) following adjustment, loosen the screw (75) using a cross-headed screwdriver and align the angle indicator along the 0° mark.

Adjusting the Clamping Force of the Clamping Handle (14) (see figure Y)
The clamping force of the clamping handle (14) can be adjusted.
Checking

• The clamping force of the clamping handle must hold the glide arm securely in place at any bevel angle. Setting
• Loosen the clamping handle (14).
• Use a socket spanner (17 mm) to turn the set screw (76) anticlockwise to reduce the clamping force or clockwise to increase the clamping force.
• Set a bevel angle, retighten the clamping handle (14) and check whether the required clamping force has been reached.

Transport (see figure Z)
Before transporting the power tool, the following steps must be carried out:

• Slide the glide arm (34) all the way back and secure it in this position.
• Make sure that the depth stop (28) is pressed all the way in and that the adjusting screw (27) fits through the recess without touching the depth stop when moving the glide arm.
• Guide the glide arm downwards until you can press the transport safety lock (35) all the way in
•  Slide the saw table extensions (8) all the way in.
• Set the bevel angle to 0° and tighten the clamping handle (14).
• Turn the saw table (42) as far as possible to the left and tighten the locking knob (12).
• Remove all accessories that cannot be securely fitted to the power tool.
• If possible, transport unused saw blades in an enclosed container.
• For transport, hold the power tool by the recessed handles (16) on either side of the saw table.
• When transporting the power tool, only use the transport fixtures. Never carry the power tool by the protective devices, the glide arm or the handle.

Maintenance and servicing

Maintenance and Cleaning

• Before carrying out any work on the power tool (e.g. maintenance, tool change etc.), remove the battery from the power tool. There is risk of injury from unintentionally pressing the on/off switch.
• To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean. The retracting blade guard must always be able to move freely and retract automatically. It is therefore important to keep the area around the retracting blade guard clean at all times.
  Always remove dust and chips after working by blowing out with compressed air or using a brush. Clean the guide roller (20) regularly.
  After-Sales Service and Application Service Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts.
  You can find explosion drawings and information on spare parts at: www.bosch- pt.com
  The Bosch product use advice team will be happy to help you  with any questions about our products and their accessories.
  In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.
  Great Britain Robert Bosch Ltd. (B.S.C.) P.O. Box 98 Broadwater Park

North Orbital Road Denham Uxbridge UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com You can find further service addresses at: www.bosch- pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legislation on the transport of dangerous goods. The user can transport
the batteries by road without further requirements.
When the batteries are shipped by third parties (e.g. air transport or forwarding agency), special requirements on packaging and labelling (e.g. ADR regulations) must be met. A dangerous goods expert must be consulted when preparing the items for shipping.
Dispatch battery packs only when the housing is undamaged. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging.
Please also observe the possibility of more detailed national regulations.
Do not dispose of power tools and batteries/rechargeable batteries into household waste!
Disposal
Power tools, rechargeable batteries, accessories and packaging should be sorted for environmental-friendly recycling.
Only for EU countries:
Power tools that are no longer suitable for use and defective or used batteries must be disposed of separately. Use the designated collection systems.
If disposed incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.
Only for United Kingdom:
According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended) and the Waste Batteries and Accumulators Regulations 2009 (SI 2009/890) (as amended), products that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.
Battery packs/batteries:
Li-ion:
Please observe the notes in the section on transport (see “Transport”, page 50). Licenses
Copyright © 2004 – 2020, Texas Instruments Incorporated All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
•  Neither the name of Texas Instruments Incorporated nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Copyright © 2009–2020 ARM LIMITED
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
• Neither the name of ARM nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Copyright © 2011 Petteri Aimonen
This software is provided ‘as-is’, without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:

1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.

EU Declaration of Conformity

Cordless sliding mitre saw| Article number| We declare under our sole responsibility that the stated products comply
with all applicable provisions of the directives and regulations listed below
and are in conformity with the following standards. Technical file at: *
---|---|---
GCM 18V-305
GDC| 3 601 M43 000| 2006/42/EC
2014/30/EU
2011/65/EU| EN 62841-1:2015+A11:2022
EN IEC 62841-3-9:2020+A11:2020
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 63000:2018
---|---|---|---

• Robert Bosch Power Tools GmbH
  (PT/ECS)
  70538 Stuttgart
  GERMANY|
  Henk Becker
  Chairman of
  Executive Management| Helmut Heinzelmann
  Head of Product Certification

Robert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANY Stuttgart, 10.02.2023
Declaration of Conformity

Cordless sliding mitre saw GCM 18V-305 GDC
Article number 3 601 M43 000
We declare under our sole responsibility that the stated products comply with all applicable provisions of the regulations listed below and are in conformity with the following standards.
Technical file at: Robert Bosch Ltd. (PT/SOP-GB), Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom
|The Supply of Machinery (Safety) Regulations 2008
The Electromagnetic Compatibility Regulations 2016
The Restriction of the Use of Certain Hazardous Substances in
Electrical and Electronic Equipment Regulations 2012
EN 62841-1:2015+A11:2022
EN IEC 62841-3-9:2020+A11:2020
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 63000:2018
Vonjy Rajakoba
Managing Director – Bosch UK Robert Bosch Power Tools GmbH, 70538 Stuttgart, Germany represented (in terms of the above regulations) by Robert Bosch Limited, Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom
Martin Sibley
Head of Sales Operations and Aftersales Robert Bosch Ltd. Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom, as authorised representative acting on behalf of Robert Bosch Power Tools GmbH, 70538 Stuttgart, Germany
Place of issue: Uxbridge Date of issue: 22/02/2023

Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com

References

• Invented for life | Bosch Global
• The domain name bosch.mk is for sale
• Početna strana | Bosch u Srbiji
• 巧米网为您服务！(QiaoMi.com)
• Skånevik Ølen Kraftlag AS
• bosch-professional.com/wac
• Электроинструменты Bosch | Bosch Professional
• Bosch Power Tools | Bosch Power Tools
• Location selection | Bosch Power Tools
• Електроинструменти на Bosch | Електроинструменти на Bosch
• Service worldwide
• Elektrické nářadí Bosch | Elektrické nářadí Bosch
• Bosch Elektrowerkzeuge und Zubehör | Bosch Elektrowerkzeuge
• Bosch el-værktøj | Bosch el-værktøj
• Bosch-sähkötyökalut | Bosch-sähkötyökalut
• Outillage électroportatif Bosch | Outillage électroportatif Bosch
• Ηλεκτρικά εργαλεία Bosch | Ηλεκτρικά εργαλεία Bosch
• Bosch elektromos kéziszerszámok | Bosch elektromos kéziszerszámok
• Elektronarzędzia Bosch | Elektronarzędzia Bosch
• Scule electrice Bosch | Scule electrice Bosch
• Bosch električni alati | Bosch električni alati
• Bosch Услуги | Электроинструменты Bosch
• Elektrické náradie Bosch | Elektrické náradie Bosch
• Contato | Bosch no Brasil
• Ana Sayfa | Bosch Türkiye
• Početna | Bosch u Hrvatskoj
• Herramientas eléctricas de Bosch | Bosch Professional
• Herramientas eléctricas de Bosch | Bosch Professional
• herramientasbosch.net
• bosch-professional.com/wac/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>