HomeSeer

Z-Wave Multi-Sensor HSM200

SKU: HSM200

Quickstart

This is a ****

Alarm Sensor
for
U.S. / Canada / Mexico.

To run this device please connect it to your mains power supply.

To add this device to your network execute the following action:
When the HSM200 has not yet been joined to a Z-Wave network, the LED blinks aqua.To Include: Put the controller into learn mode, (in the HomeSeer Z-Wave Plug-in, choose controller functions and add/include device.) then press and release the push button on the side of the HSM200. The LED will blink blue while the HSM200 is trying to join the Z-Wave network.Once joined to the network, the HSM200 enters a motion sensor test mode and the LED will blink white each time motion is detected. This mode lasts for about 5 minutes and then the LED will go out.If the HSM200 is unable to join the network, it will return to blinking aqua.

Please refer to the
Manufacturers Manual for more information.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

The HSM200 senses motion, temperature and light level, can function as a night light, and can also be programmed to display up to 7 different glowing colors when things happen in the home! Since the HSM200 is line powered, there are no batteries to change and the unit automatically operates as a Z-Wave network repeater.Installation is fast and easy. Just plug into any available 120v outlet and tap the button on the side to join it to your Z-Wave network. HSM200 is compatible with any HomeSeer HS3-based system, including the full line of HomeTrollers, and Z-Wave systems from 3rd parties.HomeSeer users can create events to display different colors when motion is sensed, doors are opened, water leaks are detected or just about anything else happens in the home. Color optionsinclude red, green, blue, yellow, magenta, cyan and white. The unit can also be programmed to work as a night light after hours.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This
procedure should only be used when the primary controller is inoperable.

Excluding from a Z-Wave network will return the device to factory defaults. See the Product Exclusion Description for details.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Inclusion

When the HSM200 has not yet been joined to a Z-Wave network, the LED blinks aqua.To Include: Put the controller into learn mode, (in the HomeSeer Z-Wave Plug-in, choose controller functions and add/include device.) then press and release the push button on the side of the HSM200. The LED will blink blue while the HSM200 is trying to join the Z-Wave network.Once joined to the network, the HSM200 enters a motion sensor test mode and the LED will blink white each time motion is detected. This mode lasts for about 5 minutes and then the LED will go out.If the HSM200 is unable to join the network, it will return to blinking aqua.

Exclusion

There are two methods for exclusion:1) Put the controller into exclusion mode, then press and release the push button on the side of the HSM200. The LED will blink aqua when no longer joined to the network.2) (Use this procedure only when your primary controller is missing or otherwise inoperable.)Press and hold the push button. The LED will blink blue faster and faster and then shift to yellow and continue to blink faster and faster. Once the LED goes out, the HSM200 is reset to the factory defaults and will blink aqua.Method 1 is recommended. Method 2 should only to be used in the event that the primary controller is missing or otherwise inoperable.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

detected. Up to four (4) Z-Wave devices can be associated in this group. The HSM200 will send a BASIC ON command to all devices that are associated in this group. Note that the Z-Wave devices in this group must be within direct range (about 30) of the HSM200. Control of nodes that are further away or blocked by metal or concrete walls should rely on the Z-Wave system controller and the home-control application for reliable operation.

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 1: OnTime

OnTime sets the number of minutes that the lights stay on when motion has not been detected.A value of 0 is a special mode where the lights are constantly sent a command to turn them on whenever motion is detected. The HSM200 will NOT turn the lights off in this mode. Recommended values:5 min for hallways20 min for an office environment60 min for a library, office or other room where someone may be sitting still for a long time
Size: 1 Byte, Default Value: 10

SettingDescription

Parameter 2: OnLevel

_OnLevel is the value sent by the Z-Wave BASICSET command to all Group 2 nodes when motion is detected. A value of 0 will turn the lights off (not recommended).A value between 1 and 99 will set the dim level to between 1% and 99% (99% is full on).A value of -1 will turn the light on which depends on the device but most will set the dim level to the last dim setting.
Size: 1 Byte, Default Value: -1

SettingDescription

Parameter 3: LiteMin

A Luminance report is sent to the system controller every LiteMin minutes if the value has changed by more than 5% since the last reading.A value of zero turns this mode off. Luminance values can still be obtained at any time by the home-control application in this mode.
Size: 1 Byte, Default Value: 60

SettingDescription

Parameter 4: TempMin

A Temperature report is sent to the system controller every TempMin minutes if the value has changed by more than 0.5F since the last reading.A value of zero turns this mode off. Temperature values can still be obtained at any time by the home-control application in this mode.
Size: 1 Byte, Default Value: 60

SettingDescription

Parameter 5: TempAdj

TempAdj is a twos-complement number that is used to adjust the temperature reading to make it more accurate. The value is in tenths of degree Fahrenheit. The temperature reading can be adjusted up to +12.7F to -12.8F. A value of 1 will adjust the temperature reading by +0.1F. A value of -1 will adjust the temperature by -0.1F. A value of 123 will adjust the temperature by +12.3F.
Size: 1 Byte, Default Value: 0

SettingDescription

Technical Data

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>