Decaura 3718 Wall Top Assemblie Instruction Manual

Inkerma DM-262 Make Great Experience User Manual

Many thanks for puchasing Decaura products, please check over carefully the surface and accessories to avoid any damage and missing parts.

For Round set

This set of tap consists of two separate kits, One for hot water (red washer in bottom of spindle) and another for cold water(blue washer), plus a allen key for screws inside handles. The two units are the same except that the steering of the spindle cartrige is reversed.

Installation Steps

1. Disassemble your new tap in three steps: 1) Take off the button cover 9 ), unscrew 9 ) with allen key and removing the handle 2) Take off the protection cap (D and unscrew the dress flange  by hand; 3) Unscrew the locking nut & from the Spindle Cartridge .
2. Double check this rubber seal washer (in Red & Blue) at the base of the spindle cartridge MUST be in a proper condition. This is very important to seal the tap.
3. Screw in the spindle cartridge by hand until it reach the tap seat. Then GENTALY TIGHTEN with a spanner, make sure tight the spindle cartridge with taps sea, any gap will cause leakage. Important: Don’t screw too hard, as it will damage the rubber seal ring or Spindle.
4. Place the fibre washer ) over the spindle and screw the lock nut & FIRMLY with a spanner.
5. Screw the dress flange ) to the locking nut. this only has to be tightened by hand.
6. Rotate the spindle cartridge to the end by hand.(counterclockwise for hot water in the left side, and clockwise for cold water in the right). Put the handle  to the spindle with the handle downward (The horizontal position for “ON”, while downsize for “OFF”). Fasten the handle tightly by screw  with allen key. Put in the button cover into the hole.

For Square set

This set of tap consists of two separate kits, One for hot water (red washer in bottom of spindle) and another for cold water(blue washer), plus a allen key for screws inside handles. The two units are the same   except that the steering of the spindle cartrige is reversed.

Installation Steps

1. Disassemble your new tap in three steps: 1) Take off the button cover ), unscrew ) with allen key and removing the handle (0); 2) Take off the protection cap (D and unscrew the dress flange  by hand; 3) Unscrew the locking nut &) from the Spindle Cartridge ) .

2. Double check this rubber seal washer (in Red & Blue) at the base of the spindle cartridge MUST be in a proper condition. This is very important to seal the tap.

3. Screw in the spindle cartridge by hand until it reach the tap seat. Then GENTALY TIGHTEN with a spanner, make sure tight the spindle cartridge with taps sea, any gap will cause leakage.
   Important: Don’t screw too hard, as it will damage the rubber seal ring or Spindle.

4. Place the fibre washer  over the spindle and screw the lock nut &) FIRMLY with a spanner.

5. Put the dress flange  to the locking nut until against to the wall by hand.

6. Rotate the spindle cartridge to the end by hand.(counterclockwise for hot water in the left side, and clockwise for cold water in the right). Put the handle (0 to the spindle with the handle downward (The horizontal position for “ON”, while downwards for “OFF”). Fasten the handle tightly by screw ) with allen key. Put in the button cover into the hole.

Remarks

1. Products are manufactured as per Australian Standard, and have WaterMark certificate.
2. The length of the cartridge is 92mm, fit for majority users. In case the water inlet seat is too deep, You may need a lengthened spindle cartridge.

Warranty Terms

All products are guaranteed as below:

1. 5 years guarantee against main body and handles.
2. 3 years guarantee against cartridge and valve defaults.
3. 2 years guarantee on washers and O-rings.
4.  3 years guarantee on finishing.

Other Conditions

1. Working pressure: 0.05-1 Mpa.
2. Working temperature: 0-55°C
3. Products are manufactured as per standard AS/NZS 3718:2005.
4. This wall top assemblies can be used for Wall basin taps, shower and bathtub taps.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>