LEVITON E5603 Decora Edge 3 Way Switch Instruction Manual
- June 10, 2024
- Leviton
Table of Contents
- SAFER, FASTER, and EASIER
- Features
- Lever Wiring Feature
- Recommended Tools
- Identify Your Wires
- Preparing Wires
- 3-Way Wiring
- Test
- Wallplate Installation Preparation
- Single-Gang Box Installation
- Multi-Gang Box Installation
- Safety First
- Limited 2 Year Warranty & Exclusions
- DIMENSIONS
- Customer Support
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
LEVITON E5603 Decora Edge 3 Way Switch
SAFER, FASTER, and EASIER
Leviton’s Decora Edge Switch makes it safer, faster, and easier to install a
new switch. Colored levers easily identify where to connect each wire. There
are no exposed wires or metal parts after installation. Built-in strip gauge.
An extra large plastic strap facilitates installation in large wall openings.
Designed for midway wallplates for extra coverage, or you can easily convert
it to use with standard wallplates by removing the break-off tabs. Built-in
alignment feature to align other Decora Edge products in a multi-gang
installation.
Features
Terminates wire with a snap
The colored levers snap shut to terminate the wires
Lever Wiring Feature
The color-coded levers easily identify where to connect the wallbox wires to
the switch.
NOTES :
- Wire colors in your wallbox may be different from the lever colors. See “Preparing Wires,” to make sure you insert the wires properly.
- Both Traveler 1 or 2 can be connected to either Traveler lever.
Recommended Tools
-
Slotted/Phillips Screwdriver
-
Wire Stripper
-
Needle Nose Pliers
-
Voltage Tester
Identify Your Wires
WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER at circuit breaker or fuse and test that power is OFF before wiring!
- Remove the wallplate and disconnect the existing switch.
- Restore power. Carefully, test the wires with a voltage tester to find the Line (hot) wire.
- Turn OFF the power at the circuit breaker or fuse.
- Label the wires, as shown.
NOTES:
- DO NOT use copper-clad wires in this device.
- Neutral wires are typically white, and may be found in the wallbox. Neutral wires are not required to operate this device.
- Use with #12 AWG or #14 AWG solid or stranded wire only.
- Ground wires may be green.
Preparing Wires
-
Make sure that the ends of the wires from the wallbox are straight (cut if necessary).
-
Strip each wire in the wallbox, as shown below.
Use Built-in Strip Gauge on the Switch
OR
Use Strip Gauge as shown below
(measure bare wire here)
3-Way Wiring
NOTE: Work on only one connection at a time.
-
Fully open lever.
-
2. Insert the proper wire into the wire hole per the wiring diagram on page 7. Make sure the wire is fully inserted and no bare wire is exposed.
NOTE: If using stranded wire twist wire before insertion.
-
Fully close lever.
-
Connect the remaining wires as shown.
Test
-
Position all wires so that there is room in the wallbox for the device.
-
Partially screw the mounting screws into the wallbox’s mounting holes.
-
Restore power at the circuit breaker or fuse.
-
Press the switch. If the Load turns ON, wiring is complete.
WARNING : Turn the power OFF at the breaker or fuse before you complete the installation. -
To complete the installation, proceed to the.
If you are unsure about the installation process, contact Leviton Technical Support, or contact an electrician.
Wallplate Installation Preparation
The switch strap is designed for midway wallplates. If you want to use a
standard size wallplate, carefully remove both break-off fins, as shown below.
Single-Gang Box Installation
WARNING : Turn the power OFF at the circuit breaker or fuse before you tighten the screws.
-
Tighten the mounting screws into wallbox.
-
Install wallplate, and restore power.
Multi-Gang Box Installation
WARNING : Turn the power OFF at the circuit breaker or fuse before you tighten the screws.
-
To install the switch next to other Decora Edge devices, use the alignment feature to easily place each device next to each other in the multi-gang box.
-
Tighten the mounting screws into wallbox.
-
Install wallplate, and restore power.
Safety First
WARNINGS :
- TO AVOID FIRE SHOCK OR DEATH; TURN OFF POWER at circuit breaker or fuse when servicing, installing or removing device.
- This product is to be installed and/or used in accordance with electrical codes and regulations.
- If you are unsure about any part of these instructions, consult an electrician.
CAUTIONS :
- Use this device with solid or stranded copper wire only.
- DO NOT use this device with copper clad wire.
- To avoid damage to the product, DO NOT use disinfecting products, including foggers, sprays or other types of atomized cleaning agents.
- DO NOT spray liquid onto the product.
- To clean, use a damp cloth with mild soap.
PATENT STATEMENT
Patents covering this product, if any, can be found on
Leviton.com/patents.
Limited 2 Year Warranty & Exclusions
For Leviton’s limited product warranty, go to www.leviton.com. For a printed copy of the warranty, call 1-800-824-3005.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should
contact Leviton in writing at Leviton Manufacturing of Canada ULC to the
attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire
(Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
Scan this QR code for additional Decora Edge product information and to view
the install video.
DIMENSIONS
Customer Support
Visit leviton.com/support or contact Technical
Services at 1-800-824-3005 for
additional help.
References
- Patent Numbers | Leviton
- Product Support
- Leviton | Switches, Dimmers, Outlets & Lighting Controls
- Product Support
- Leviton Product Support | Contact Us
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>