BEGA 66157 Compact Downlight Instruction Manual
- June 12, 2024
- BEGA
Table of Contents
66157 Compact Downlight
Instruction Manual
66157 Compact Downlight
Compact downlight
Instructions for use
Application
Compact downlight with symmetrical wide beam light distribution.
Product description
Luminaire made of aluminium alloy, aluminium and stainless steel BEGA Unidure ® coating technology Colour graphite or white Safety glass with optical structure Silicone gasket BEGA Vortex Optics ® . Reflector surface made of pure luminium 2 mounting holes ø 4.8 mm Distance apart 70 mm 1 cable entry for mains supply cable up to ø 10,5 mm Connection terminal 2.5@ Earth conductor connection BEGA Ultimate Driver ® LED power supply unit 220-240 V x /50-60 Hz DC 176-264 V BEGA Thermal Switch ® Temporary thermal shutdown to protect temperature-sensitive components Safety class I Protection class IP 65 Dust-tight and protection against water jets Impact strength IK06 Protection against mechanical impacts < 1 joule – Safety mark – Conformity mark Weight: 0.85 kg This product contains light sources of energy efficiency class(es) C
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
| Module connected wattage | 3 W |
|---|---|
| Luminaire connected wattage | 4.1 W |
| Rated temperature | ta = 25 °C |
| Ambient temperature | ta max = 50 °C |
66 157 K3
| Module designation | LED-0591/830 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 80 |
| Module luminous flux | 560 lm |
| Luminaire luminous flux | 424 lm |
| Luminaire luminous efficiency | 103,4 lm / W |
66 157 K4
| Module designation | LED-0591/840 |
|---|---|
| Colour temperature | 4000 K |
| Colour rendering index | CRI > 80 |
| Module luminous flux | 580 lm |
| Luminaire luminous flux | 440 lm |
| Luminaire luminous efficiency | 107,3 lm / W |
Lighting technology
Half beam angle 40°
Installation
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping.
Undo the screws and lift off the luminaire top.
Lead the mains supply cable through the cable entry into the luminaire back
housing. Fix luminaire base with enclosed or any other suitable fixing
material onto the mounting surface.
Be sure to use the gasket rings supplied.
Make earth conductor connection.
Push silicone sleeves over the lines and make electrical connection.
In order to guarantee the maximum service life of the electrical components,
the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the
position marked by the red information label immediately before finally
closing the luminaire.
Make earth conductor connection between luminaire top and luminaire base.
Push plug into coupler as far as it will go.
Install the luminaire top (as displayed in the sketch),
press-on and tighten screws evenly.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits. Do not use high pressure cleaners.
Please note:
Do not remove the desiccant bag from the luminaire housing. It is needed to
remove residual moisture.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
| Housing + Glass graphite | 25 000 013 |
|---|---|
| Housing + Glass white | 25 000 014 |
| LED power supply unit | DEV-0303/350 |
| LED module 3000 K | LED-0591/830 |
| LED module 4000 K | LED-0591/840 |
| Reflector | 76 001 428 |
| Gasket | 83 001 570 |
BEGA Gantenbrink-Leuchten KG ·
Postfach 31 60 ·
58689 Menden ·
info@bega.com ·
www.bega.com
66 157
Documents / Resources
| BEGA
66157 Compact
Downlight
[pdf] Instruction Manual
66157K3, 66157K4, 66157 Compact Downlight, Compact Downlight, Downlight
---|---