Commercial Electric 56568191 7.5 Inch LED Color Changing Recess Or Surface Mount Fixture with Night Light User Guide

Commercial Electric 56568191 7.5 Inch LED Color Changing Recess Or

Surface Mount Fixture with Night Light

PACKAGE CONTENTS

HARDWARE INCLUDED

NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker before removing an existing light fixture or installing the new one.

INSTALLATION

Select a suitable location that can support the weight of the fixture. Determine the method for mounting the fixture before drilling, based on the type of ceiling.

SURFACE MOUNTING WITHOUT RECESSED MOUNTING BRACKET

1. Pass the hot and neutral (black and white) wires from the electrical outlet box through the middle hole of the mounting bracket (AA). Align the mounting bracket (AA) using the mounting screws (BB) and tighten securely to the electrical box.
2. Connect the hot and neutral (black and white) wires from the fixture body (A) to the same color wires from the electrical box.| Cover the wire connectors (EE) with electrical tape for a more secure connection.
3. Position the wires back inside the electrical box. Align the side slots on the fixture body (A) with the mounting bracket (AA) and fix the fixture body (A) securely by carefully rotating in clockwise the side slots inside the mounting bracket (AA).
4. Restore power at the electrical panel. Turn on the light switch to activate the fixture.

Surface Mounting With Recessed Mounting Bracket

1. Mark the mounting location on the mounting surface, then drill a 6.0 to 6.5-in. hole large enough to insert the fixture body (A) into mounting location.
2. Mount the fixture body (A) to the electrical box (CC) using the two electrical box screws (for Electrical Box) (DD).
3. Fix the wire pipe (not included) on the electrical box plate, and then feed the electrical connection wires through the pipe (not included).
4. Connect the black to black(hot) and the white to white (neutral) wire. Connect the ground (green) wire from the electrical box plate and the green wire from the electrical box (CC) with the ground wire from the electrical box (end user J-box, not included). Cover the wire connectors (EE) with electrical tape for a more secure connection.
5. Fasten the plate to the electrical box (CC) with the pre-installed screw on the electrical box (CC).
6. Insert one side of the fixture into the mounting hole and firmly push against the spring clip while inserting the other side into the hole. Carefully push the fixbody body (A) into the mounting hole until it’s attached to the surface securely.

Mount to 6 in. Housing

1. Fix the mounting clip (GG) on the fixture body (A) by using two screws (DD). Make sure the power is turned off at the source to the recessed can housing where the fixture will be installed. Remove the existing bulb and trim, revealing the socket. NOTE: Stick the replacement label on the inner wall of the recessed housing before installation.
2. Screw the medium base (E26) socket adapter (FF) into the socket in the recessed housing. Connect the hot and neutral (black and white) wires from the fixture body (A) to the same color wires from the socket adapter (FF). Cover the wire connectors (EE) with electrical tape for a more secure connection.
3. Carefully push the fixture body (A) into the recessed can housing until the trim is flush with the ceiling surface.
   NOTE: Select the preferred color temperature and brightness before pushing the fixture body into the recessed can housing.

ADJUSTING THE COLOR TEMPERATURE OF THE LIGHT

This LED light fixture allows you to customize the color temperature of the light using three settings: soft white, bright white, or daylight.

1. Choose your favorite correlated color temperature (CCT) from three options: 3000k Soft White, 4000k Bright White, or 5000k Daylight.
2. Move the toggle switch on the fxture body (A) to make your selection before inserting into bracket or ceiling.
   NOTE: The factory setting for the correlated color temperature (CCT) is 3000K.

LIGHT DISTRIBUTION

SELECTING MAIN LIGHT OR NIGHTLIGHT MODE
The product can be used in one of two modes: Main light mode, which provides full brightness and allows selection from three color temperatures, or nightlight mode. Nighlight mode provides reduced light output at 2000K color temperature for very soft illumination at night.

TO TURN ON THE MAIN LIGHT
Turn on the light switch to activate the light fixture.

TO CHANGE TO NIGHTLIGHT MODE WITH REDUCED LIGHT OUTPUT
Switch the main light off and back on again within 3 seconds to active nightlight mode.
NOTE: The main light will not provide light output when the nightlight trim is illuminated.

TO RETURN TO THE MAIN LIGHT WITH FULL LIGHT OUTPUT WHEN IN NIGHTLIGHT MODE
Toggle the switch off and back on to active.

CARE AND CLEANING

CAUTION: Before attempting to clean the tube and luminaire/light fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box. Clean with a soft, dry cloth. Do not use cleaners with chemicals, solvents, or harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring.

TROUBLESHOOTING

Minor problems often can be fixed without the help of an electrician.

WARNING:
Before doing any work on the fixture, disconnect power to the light fixture.

Contact a qualified electrician.
There is a defective switch.| Contact a qualified electrician.
The fuse blows or the circuit breaker trips when the light is turned on.| The wires are crossed or the power wire is grounding out.| Check the wire connections. Contact a qualified electrician or call Commercial Electric customer service at 1-877-527-0313 or visit www.HomeDepot.com.
The light fixture flickers or makes a buzzing sound.| The dimmer circuit is not compatible with the product.| Check the product page at www.HomeDepot.com for a list of compatible dimmers.
The dimming circuit is set outside the dimming

range of the product.

| Turn or slide the dimmer switch to adjust the light output until the flickering or buzzing stops.
Out of sync| Slide the dimmer too fast.| Turn off the wall switch for more than 3 seconds, then turn back on.
The dimmer circuit is not compatible with the product.| Check the product page at www.HomeDepot.com for a list of compatible dimmers.

WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal.

• Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
• This product must be installed in accordance with the applicable installation codes by a person familiar with the construction and operation of the product and the hazards involved.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• Risk of electrical shock. To reduce the possibility of serious injury, always take the proper precautions and unplug the fixture before moving or cleaning.
• Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components.
• Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
• Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

NOTICE: Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
NOTICE: Suitable for operation in ambient temperatures not exceeding 104°F/40°C.
NOTICE: Suitable for damp locations.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and consult the dealer or an experienced radio/TV. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

WARRANTY

WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling.

WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in anyway not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.
The manufacturer does not warrant and specifically disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product. Contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.

Questions, problems, missing parts? Before returning to the store, call Commercial Electric Customer Service
8 a.m. – 7 p.m., EST, Monday – Friday
9 a.m. – 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
Retain this manual for future use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>