JONATHAN Y JYL9914 Mila 11 Inch Tall LED Wall Sconce Instruction Manual

: June 12, 2024
: JONATHAN Y

Table of Contents

JONATHAN Y JYL9914 Mila 11 Inch Tall LED Wall Sconce
CARE AND MAINTENANCE
NOTICE& IMPORTANT SAFETY INSTRUCTIONS
Part List and Hardware List
PREPARATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JONATHAN Y JYL9914 Mila 11 Inch Tall LED Wall Sconce

Model# : JYL9914
Product Dimensions : 5.5”W X 11.3″H X 5.7″E

WARNING

WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL IT. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.

CARE AND MAINTENANCE

To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture. To clean the inside of the fixture, first disconnect the power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture. Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only dry soft cloth to dust or wipe carefully.

NOTICE& IMPORTANT SAFETY INSTRUCTIONS

Please make sure that you have all parts indicated before you begin assembly of this item
This item should be assembled on a soft surface to prevent scratching the finish during assembly
To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation
The external flexible cable or cord of this lamp cannot be replaced If the cord is damaged, the lamp shall be destroyed

Part List and Hardware List

JONATHAN-Y-JYL-9914-Mila-11-Inch-Tall-LED-Wall-Sconce-
fig-1

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.Estimated Assembly Time: 20 minutes.

Fix the mounting bracket(B) to the outlet box with machine screw(A).
Make wire connections, with wire connectors(C), following the reference chart listed below.
Connect, Hot, Black or Red Outlet Supply Wire to:| Connect, Neutral, White Outlet Supply Wire to:
---|---
Black| White

Parallel Cord (round & smooth)| * Parallel Cord (square & ridged)

Clear, Brown, Gold or Black without Tracer (colored stripes)

|

Clear, Brown, Gold or Black with Tracer (colored stripes)

Insulated Wire (not green) with copper metal conductor

|

Insulated Wire (not green) with Silver metal conductor.

Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions:

  * For installation in the United States: Wrap ground wire from the outlet box around the green ground screw on the mounting bracket, no less than 2″ from the wire end. Tighten the ground screw. If the fixture is supplied with a ground wire, connect to the outlet ground wire with a wire connector.
  * For installation in Canada: If the fixture is supplied with ground wire, wrap ground wire around the green grounding screw on the mounting bracket. Tighten the ground screw.

Orient the Back Plate(E) so that the Machine screw(D) protruding from the mounting bracket go into the holes in the back plate, then secure it with the Screwed Nut(F)
The Cylinder Nut( I ) passes through the Rubber Pad(H) and enters the hole of the Glass Shade(G) to fix the Glass Shade(G) on the Back Plate(E)
Install bulbs(J). Be sure to use a light bulb(J) with a wattage no greater than specified on this fixture. Always make sure that the electrical current is turned off before changing bulbs.