VIVO DESK-E3CTB Black 63 Inch x 55 Inch Corner Electric Desk Instruction Manual
- June 15, 2024
- Vivo
Table of Contents
VIVO DESK-E3CTB Black 63 Inch x 55 Inch Corner Electric Desk Instruction Manual
vivo-us.com/products/desk-e3ctb
help@vivo-us.com
www.vivo-us.com
Contact Us First!
DO NOT RETURN ITEM
Our friendly product support team is here to help!
PERSONABLE CUSTOMER SUPPORT
7AM – 7PM
Monday-Friday
Give us a Call: 309-278-5303
Chat Us: www.vivo-us.com
Email Us: help@vivo-us.com
We’re Here for You!
Our customer-minded support team is here for YOU, Monday-Friday 7am-7pm CST.
We offer immediate assistance with rapid response times from customer service
agents and product technicians to
help you every step of the way!
Missing a Part?
If any parts are received damaged / defective OR you are missing a part,
please reach out to us within 30 days of
product delivery to have it replaced at no cost. We are happy to replace parts
to ensure you have a fully
functioning product
PRE-ASSEMBLY
BEFORE YOU BEGIN
⚠ If you do not understand these directions, or if you have any doubts about
the safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
ELECTRICAL WARNING :
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND
ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
- DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
- DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
- NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE DAMAGED PARTS.
- NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT WITH LIQUIDS.
- ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
- OUTDOOR USE IS PROHIBITED.
WEIGHT CAPACITY
DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.
Product Warranty For the most up to date details on your product’s warranty, please visit the product’s listing on our website or reach out to customer support. vivo-us.com/products/desk-e3ctb
Returns | Product Didn’t Work Out? We offer a hassle-free 30 day return on all products. Contact customer support at 309-278-5303 or help@vivo-us.com. Please note: For items ordered in error or no longer needed, the return shipping charges will be at the buyer’s expense.
TOOLS NEEDED
PACKAGE CONTENTS
Please consult the parts list below and ensure you have everything you need to assemble your product. If parts are missing or damaged, please contact us.
ASSEMBLY STEPS
ASSEMBLY OPTION A | Left Side Extension
A-STEP 5: Install Anti-Vibration Pads
Affix Anti-Vibration Pads (T) to desk frame, Short Connector Bracket (M), and
Long Connector Bracket (N). Connector Brackets will be installed in next step.
A-STEP 6: Assemble Desktop
Connect Left, Middle, and Right Desktop (A, B, C) pieces together using
Desktop Connectors (O), M5x16mm Screws (S-C) and a Phillips screwdriver.
A-STEP 7: Install Connector Brackets
Begin connecting frame to desktop by placing assemblies on desktop as shown
below. Connect Angled Right Crossbar (G) and Right Crossbar (F) to Long
Connector Bracket (N), M6x8mm Screws (S-A), and 5mm Allen Wrench (T-A).
Connect Short Connector Bracket (M) to Short Left Crossbar (E) and Left
Crossbar (D), using M6x8mm Screws (S-A), and 5mm Allen Wrench (T-A).
A-STEP 8: Secure Frame & Desktop
Secure to desktop with M5x16mm Screws (S-C) and a Phillips screwdriver, using
the screw locations shown below. Connect Control Panel (Q) to desktop using
M5x16mm Screws (S-C) and a Phillips screwdriver.
A-STEP 9: Install Sync Rod
Loosen the coupling nut on Sync Rods (H) and insert hex shaft into Left and
Right Leg (L, J), making sure the metal retaining ring makes contact with the
leg. Ensure that all three legs are the same height. If not, turn the Sync Rod
(H) clockwise to raise corresponding leg, and counter-clockwise to lower.
Loosen coupling nuts on Sync Rods (H) and extend onto Motorized Leg (K).
Tighten coupling nuts, then tighten both set screws on the end of Sync Rods
(H) using 2mm Allen Wrench (T-B).
A-STEP 10: Connect Power Cables
Connect Power Cord (R) and cable from Motorized Leg (K) to Control Panel (Q).
If needed, use Extension Cable (S) for cable from Motorized Leg (K) to extend
length. Use Cable Clips (U) to secure cables to desktop.
ASSEMBLY OPTION B | Right Side Extension
B-STEP 5: Install Anti-Vibration Pads
Affix Anti-Vibration Pads (T) to desk frame, Short Connector Bracket (M), and
Long Connector Bracket (N). Connector Brackets will be installed in next step.
B-STEP 6: Assemble Desktop
Connect Left, Middle, and Right Desktop (A, B, C) pieces together using
Desktop Connectors (O), M5x16mm Screws (S-C) and a Phillips screwdriver.
B-STEP 7: Install Connector Brackets
Begin connecting frame to desktop by placing assemblies on desktop as shown
below. Connect Angled Right Crossbar (G) and Right Crossbar (F) to Long
Connector Bracket (N), M6x8mm Screws (S-A), and 5mm Allen Wrench (T-A).
Connect Short Left Crossbar (E) and Left Crossbar (D) to Short Connector
Bracket (M), M6x8mm Screws (S-A), and 5mm Allen Wrench (T-A).
B-STEP 8: Secure Frame & Desktop
Secure to desktop with M5x16mm Screws (S-C) and a drill, using the screw
locations shown below. Connect Control Panel (Q) to desktop using M5x16mm
Screws (S-C) and a drill.
B-STEP 9: Install Sync Rod
Loosen the coupling nut on Sync Rods (H) and insert hex shaft into Left and
Right Leg (L, J), making sure the metal retaining ring makes contact with the
leg. Ensure that all three legs are the same height. If not, turn the Sync Rod
(H) clockwise to raise corresponding leg, and counter-clockwise to lower.
Loosen coupling nuts on Sync Rods (H) and extend onto Motorized Leg (K),
making sure set screw faces out. Tighten coupling nuts, then tighten both set
screws on the end of Sync Rods (H) using 2mm Allen Wrench (T-B).
B-STEP 10: Connect Power Cables
Connect Power Cord (R) and cable from Motorized Leg (K) to Control Panel (Q).
If needed, use Extension Cable (S) for cable from Motorized Leg (K) to extend
length. Use Cable Clips (U) to secure cables to desktop.
CONTROLLER – USER MANUAL
Memory Mode To save a set height, press and hold the “1” button for 5 seconds until “H1” appears. Your height setting is now stored. Follow steps for the other numerical buttons to save up to four height settings.
Reset Mode If the height of the desk is incorrect, press the down arrow until the desk moves to the fully lowered position. Press and hold the down arrow. “RES” will be displayed and the leg will lower and rebound upwards. Release the down arrow and your frame has been reset.
Troubleshooting
E10 Sensorless Alarm: This alarm triggered when the sensor cannot be detected.
Power off desk and check the connection between the motor and control panel,
then re-power.
E20 Overload Alarm: Remove desk items and try again.
E02 Rebound Protection: Check for desk vibration, obstacles, or desk incline.
If no issues found, complete the reset process and try again.
E32 Overvoltage Alarm: Voltage is higher than allowed value. Power off desk
and check connection between power and control panel. Power on again.
E31 Undervoltage Alarm: Voltage is lower than required value. Power off desk
and check connection between power and control panel. Power on again.
HOT Overheated Alarm: Power off and wait 18 seconds before use again.
CHECK OUT OTHER GREAT PRODUCTS FROM
EXPLORE MORE AT VIVO-US.COM We offer a wide array of home & office products to
fit your needs. From height adjustable desks to monitor mounts to keyboard
trays and more!
SPEAKER MOUNTS & STANDS
Whether you’re mounting a soundbar or surround sound system, we’ve got a
mounting solution to fit your needshttps://vivo-us.com/collections/speaker-
mounts-and-stands
CABLE MANAGEMENT
From single monitor mounts to hex mount, gromment or clamp-ons, we’ve got a
mounting solution for your setup.https://vivo-us.com/collections/speaker-
mounts-and-stands
MONITOR MOUNTS
From single monitor mounts to hex mount, gromment or clamp-ons, we’ve got a
mounting solution for your setup.
https://vivo-us.com/collections/monitor-mounts
WHO WE ARE
VIVO is more than a brand of ergonomic office furniture. We are a team of
creative and innovative individuals working together to offer high quality,
affordable ergonomic solutions. We think and work outside of the box to serve
you, our customer, to the best of our abilitiy.
Need Assistance?
We Would Love to Help!
Personable Customer Support | Mon-Fri 7am-7pm We offer immediate assistance
with rapid response times from customer service agents and product technicians
to help you every step of the way!
Call Us: 309-278-5303
Average Resolution Time: 5m 4s
Chat Us: www.vivo-us.com
Average Resolution Time: < 15m
Email Us: help@vivo-us.com
Average Resolution Time: 1HR 8M
23% within < 15m
38% within < 30m
61% within < 1hr
83% within <2hr
92% within < 3hr
LOVE YOUR NEW VIVO SETUP? Ready to share that new amazing setup? Want to brag
about that amazing new ergonomic solution?
Tag us in your photo!
FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO-
US.COM
LAST UPDATED: 09/27/2022 REV2LF
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Corner Electric Desk – VIVO - desk solutions, screen mounting, and more
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>