MW SDR-240 Series 240W Single Output Industrial DIN RAIL with PFC Function Owner’s Manual
- June 12, 2024
- MW
Table of Contents
MW SDR-240 Series 240W Single Output Industrial DIN RAIL with PFC Function
Owner’s Manual
Features
- High efficiency 94% and low power dissipation
- 150% peak load capability
- Built-in active PFC function, PF>0.93
- Protections: Short circuit / Overload / Over voltage / Over temperature
- Cooling by free air convection • Can be installed on DIN rail TS-35/7.5 or 15
- UL 508 (industrial control equipment) approved
- BS EN/EN 61000-6-2(BS EN/EN 50082-2) industrial immunity level
- Built-in DC OK relay contact
- 100`)/0 full load burn-in test
GTIN CODE
MW Search: https://www.meanwell.com/serviceGTlN.aspx
SPECIFICATION
| MODEL | SDR-240-24 | SDR-240-48 |
|---|---|---|
| OUTPUT | DC VOLTAGE | 24V |
| RATED CURRENT | 10A | 5A |
| CURRENT RANGE | 0 ~ 10A | 0 ~ 5A |
| RATED POWER | 240W | 240W |
| PEAK CURRENT | 15A | 7.5A |
| PEAK POWER Note.6 | 360W (3sec.) | |
| RIPPLE & NOISE (max.) Note.2 | 50mVp-p | 50mVp-p |
| VOLTAGE ADJ. RANGE | 24 ~ 28V | 48 ~ 55V |
| VOLTAGE TOLERANCE Note.3 | ±1.0% | ±1.0% |
| LINE REGULATION | ±0.5% | ±0.5% |
| LOAD REGULATION | ±1.0% | ±1.0% |
| SETUP, RISE TIME | 650ms, 60ms/230VAC 1300ms, 60ms/115VAC at full |
load
HOLD UP TIME (Typ.)| 20ms/230VAC 20ms/115VAC at full load
INPUT| VOLTAGE RANGE| 88 ~ 264VAC 124 ~ 370VDC
FREQUENCY RANGE| 47 ~ 63Hz
POWER FACTOR (Typ.)| 0.94/230VAC 0.99/115VAC at full load
EFFICIENCY (Typ.) Note.8| 94%
AC CURRENT (Typ.)| 2.6A/115VAC 1.3A/230VAC
INRUSH CURRENT (Typ.)| 33A/115VAC 55A/230VAC
LEAKAGE CURRENT| <1mA / 240VAC
PROTECTION| **OVERLOAD**| Normally works within 110 ~ 150% rated
output power for more than 3 seconds and then shut down o/p voltage with auto-
recovery
150% rated power, constant current limiting with auto-recovery within 2 seconds and may cause to shut down if over 2 seconds
**OVER VOLTAGE| 29 ~ 33V| 56 ~ 65V
Protection type : Shut down o/p voltage with auto-recovery
****OVER TEMPERATURE| 95℃±5℃ (TSW : detect on heatsink of power switch)
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
FUNCTION| DC OK REALY CONTACT RATINGS (max.)| 60Vdc/0.3A, 30Vdc/1A, 30Vac/0.5A resistive load
ENVIRONMENT| WORKING TEMP. Note.5| -25 ~ +70℃ (Refer to “Derating Curve”)
WORKING HUMIDITY| 20 ~ 95% RH non-condensing
STORAGE TEMP., HUMIDITY| -40 ~ +85℃, 10 ~ 95% RH
TEMP. COEFFICIENT| ±0.03%/℃ (0 ~ 50℃)
VIBRATION| Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6
SAFETY & **EMC (Note 4)| SAFETY STANDARDS| UL508, TUV BS EN/EN62368-1, AS/NZS 62368.1, EAC TP TC 004 approved;(meet BS EN/EN60204-1)
WITHSTAND VOLTAGE| I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC
ISOLATION RESISTANCE| I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION| Compliance to BS EN/EN55032 (CISPR32), BS EN/EN61204-3 Class B, BS EN/EN61000-3-2,-3, EAC TP TC 020
**EMC IMMUNITY| Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN55035, BS EN/EN61000-6-2 (BS EN/EN50082-2),BS EN/EN61204-3, heavy industry level, EAC TP TC 020, SEMI F47 approved
OTHERS| MTBF| 1160.3K hrs min. Telcordia SR-332 (Bellcore) ; 169.3K hrs min. MIL-HDBK-217F (25℃)
DIMENSION| 63125.2113.5mm (WHD)
PACKING| 1.03Kg; 12pcs/13.4Kg/1.22CUFT
NOTE**|
- All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
- Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
- Tolerance : includes set up tolerance, line regulation and load regulation.
- The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives
- Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power. In case the adjacent device is a heat source, 15mm clearance is recommended.
- 3 seconds max., please refer to peak loading curves.
- Derating may be needed under low input voltage. Please check the derating curve for more details.
- After 30 minutes of burn-in.
- The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
Mechanical Specification
Terminal Pin No. Assignment (TB1)
| Pin No. | Assignment |
|---|---|
| 1 | FG |
| 2 | AC/N |
| 3 | AC/L |
Terminal Pin No. Assignment (TB2)
| Pin No. | Assignment |
|---|---|
| 1,2 | Relay Contact |
| 3,4 | DC OUTPUT +V |
| 5,6 | DC OUTPUT -V |
Block Diagram
| Contact Close | PSU turns on / DC OK. |
|---|---|
| Contact Open | PSU turns off / DC Fail. |
| Contact Ratings (max.) | 30V/1A resistive load. |
Peak Loading
Derating Curve
AMBIENT TEMPERATURE ( )
Output derating VS input voltage
INPUT VOLTAGE (V) 60Hz
File Name: SDR-240-SPEC 2022-09-20
Symbols
Documents / Resources
| MW
SDR-240 Series 240W Single Output Industrial DIN RAIL with PFC
Function
[pdf] Owner's Manual
SDR-240 Series 240W Single Output Industrial DIN RAIL with PFC Function,
SDR-240 Series, 240W Single Output Industrial DIN RAIL with PFC Function,
Industrial DIN RAIL with PFC Function, RAIL with PFC Function, PFC Function
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>