Signify FLP 2 Ft Series FluxSpace LED Linear Strip Installation Guide

: June 12, 2024
: signify

Table of Contents

Day-Brite
- Linear
- References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Classified

Day-Brite

by

Linear

FluxSpace 442296079081

FLP 2′, 3′, 4′, & 8′

CAUTION: THE INSTALLATION AND SERVICING OF THIS PRODUCT SHOULD BE PERFORMED BY A QUALIFIED ELECTRICIAN OR SERVICE PERSONNEL

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital service, pursuant to Part 15 of the FFC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, many cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Tools / accessories needed (not included):

(1) ¼ hexagonal screwdriver
2ft-3ft – (2) # ¼ screws
4ft-8ft – (4) # ¼ screws

Parts

Lens
WWC
Endcap
Housing

It is suggested to make the installation with two persons.

SURFACE MOUNT VERSION

Step 1

To remove the lens, it has to be squeezed, starting from one end and doing it until it reaches the other end to release the lens from lances. Once the lens is released from the lances slide it to one side and then lift it from one end and remove it, as shown in Figure 1.

Figure 1. Removing Lens

push

Step 2

Remove the screws located on the sides of the LED board with a hexagonal ¼ screwdriver, as shown in figure 2.A

Note: In case of 2 LED rows, it will be a single screw, as shown in figure 2.B

Figure 2. A Figure 2. B

www.day-brite.com www.cfi- lighting.com

IS-442296079081

Step 3

Slide the WWC to the opposite side of the lances and then pull up the WWC so that it can be removed, as shown in figure 3.B

One row Two rows

Figure 3.A

Note: The lances are shown in figure 3.A (for one row and two rows).

Figure 3.B Removing WWC

Step 4

Locate the wires for electrical connections. The wires are placed in the wire manager, shown in figure 4.

Figure 4.

Step 5

Wiring connections:
– White: neutral
– Green: ground
– Black: line
– Violet & Pink: dimming

Note: For 4ft & 8ft version, take out the connection wires through the 2’’ K.O in the middle. Place the 2’’ K.O. below the connection box on the mounting surface. If needed move the ground cable closer to the 2’’ K.O.

Step 6

Place the luminaire upside down against the mounting surface.

It’s recommended to measure the distance between the two installation slots and mark its position on the surface where its going to be installed.

Figure 6.

Step 7

Hold the luminaire until you have put the necessary screws to mount it and check that it is properly fixed to the desired surface.

Figure 7.A For 2ft (Use two holes to place the surface mount screws).

Figure 7.B For 3ft use selected holes.

Figure 7.C For 4ft (in case the holes marked with the arrows are not available, use the four enclosed in dotted line).

Figure 7.D For 8ft (in case the holes marked with the arrows at the edges are not available, use the four enclosed in dotted line).

Step 8

Once electrical connections are done the WWC needs to be installed.

Tilt the WWC until it touches the endcap in the opposite side where the lances are placed. Lower it until it sits in the housing and slide it to the opposite side until the lances make contact with the endbracket.

Note: Be sure not to bruise the wires when installing the WWC.

Signify FLP 2 Ft Series - Figure 8 Figure 8.

The lances are shown in the drawing.

Step 9

Install the screws removed on step 2.

Note: When using optic lens, Install the removed metal brackets in step 3. figures 3. C and 3.D by placing them in position and screwing them.

Two screws One screw

Figure 9.

Step 10

Tilt the lens until it touches the endcap. Lower the lens until is in contact with the WWC then center the lens in a way that it is held by both endcaps. Finally squeeze the lens until it engages with the lances.

Figure 10.

push

V HOOK VERSION

(V Hook accessories sold separately or provided by others)

Step 1

Turn the luminaire upside down and hold it.

Figure 11.

Step 2

Locate the K.O / Wire manager in the housing and remove it with a screwdriver. This process will make the wires available for connection as shown on figure 12.

Signify FLP 2 Ft Series - Figure 12 Figure 12.

Step 3

Wiring connections:
– White: neutral
– Green: ground
– Black: line
– Violet & Pink: dimming

Step 4

Join the extremes of the chain and introduce them into the V-hook as shown in the figure 13.

Figure 13.

Step 5

Insert V-Hooks in the housing as shown in the figure 14.

Note: Make sure the hooks point towards the middle section of the luminaire

Figure 14.

Step 6

Attach the chains to the ceiling.

Figure 15.

SLIDING HANGER

(Hanger accessories sold separately)

Step 1

Remove the lens and WWC, as shown in steps 1-3 of Surface mount.

Step 2

Take the sliding hanger and screw it in the ceiling, as shown in figure 16.

Figure 16.

Step 3

Place the luminaire upside down, hold and push the luminaire from bottom to top, as shown in figure 17.

Figure 17.

Step 4

Install the WWC and lens, as shown in steps 8-10 of Surface mount.

IN-ROW MOUNTING

(Row Joiner accessory sold separately

Step 1

Remove the endcap on one side by removing the screw and pulling the endcap out of its position, as shown in figure 18.A

Figure 18.A Figure 18.B

Note: In the figure 18.B is shown the luminaire with the endcap removed

Step 2

Slide the bracket in the luminaire and align the hole on the bracket with the hole on the luminaire, as shown in figure 19.A and screw both parts together as in figure 19.B

Figure 19.A Figure 19.B

Holes to align

Step 3

Slide the center mullion into the square cut in the housing and slide the other luminaire into the bracket, as shown in figure 20.A

Note: If you want to hang the luminaire in the union of both fixtures fold the tabs circled in figure 19.A.
Make sure to close the V hooks with pliers for safety, this will prevent the V Hooks from sliding out of the bracket.

Figure 20.A Figure 20.B

Center Mullion

Step 4

Screw the luminaire slided in step 3 to the bracket as shown in figure 21.

Figure 21

© 2021 Signify Holding. All rights reserved. The information provided herein is subject to change, without notice. Signify does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract, unless otherwise agreed by Signify.

Signify North America Corporation
400 Crossing Blvd, Suite 600
Bridgewater, NJ 08807, USA
Telephone 855-486-2216

Signify Canada Ltd.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Telephone 800-668-9008

All trademarks are owned by Signify Holding or their respective owners.

4/4/2023