Golden Lighting 3699-A1W BCB-OP Glenn 1 Light Brushed Champagne Bronze Articulating Wall Sconce Instruction Manual
- June 12, 2024
- GOLDEN LIGHTING
Table of Contents
Golden Lighting 3699-A1W BCB-OP Glenn 1 Light Brushed Champagne Bronze
Articulating Wall Sconce Instruction Manual
INSTRUCTION
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures hould hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
Love your light and want to show it off? Follow us, share a picture, and tag us on Social..
Assembly Instructions
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. (PLEASE NOTE: This fixture has multiple installation options.
Before beginning, please review these instructions carefully.) TO INSTALL ON A
WALL AND POWER THE FIXTURE USING THE PLUG REFER TO DIAGRAM (1): 1. Mounting
plate (B) is attached to backplate (D) already by the factory. Hold the
fixture up to the wall to test placement for backplate (D). Check that the
backplate (D) is horizontal and perpendicular to the ground. After you
determine the proper placement, measure the keyhole distance on the backplate
(D), mark the same distance on the wall with a pencil, then a drill bit is
used to make a hole in the pencil marks. 2. Insert plastic screw anchors (A)
into the holes made until the plastic screw anchors (A) are flush with the
wall. 3. Using screwdriver insert mounting screws (C) into the plastic screw
anchors (A). Do not insert the entire screw flush to the wall. Leave about
2-3mm of the screw’s threads outside of the wall. TO INSTALL OVER AN EXISTING
JUNCTION BOX AND HARDWIRE THE FIXTURE REFER TO DIAGRAM (2) AND THE SIDE
DIAGRAMS WHICH DIFFERENTIATE MOUNTING PLATE (N) FROM MOUNTING BRACKET (B): 1.
Mounting plate (N) is attached to backplate (D). To begin, remove mounting
plate (B) from backplate (D) so that only mounting bracket (N) is used. Place
mountingbracket (N) up against your junction box. Insert mounting screws (A)
into the mounting bracket (N). Position the mounting bracket so that the
mounting screws (A) are level and parallel with the floor. Use nuts (F) to
hold mounting screws (A) in place. 2. Leave at least 8 to 10 inches of fixture
wire for wiring. Use a pair of scissors to trim the plug-in cord (P) as shown
on the diagram. Pull the cord (P) up through the hole in the bottom of the
backplate (D) and plug the hole with stopper (O). 3. Pull the house wires from
the junction box through the center of the mounting bracket (N). Secure
mounting bracket (N) to the junction box with mounting screws (C) and a
screwdriver. Tighten the screws securely.
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.
CONNECTING THE WIRES
IF HARDWIRING THE FIXTURE TO WALL, REFER TO DIAGRAM LABELED “(2)” AND THE
WIRING INSTRUCTIONS BELOW. DO NOT FOLLOW THESE WIRING INSTRUCTIONS IF YOU ARE
MOUNTING FIXTURE TO THE WALL AND USING PLUG TO POWER FIXTURE, ALSO REFERRED TO
AS DIAGRAM LABELED “(1)”. 4. Have an assistant support the fixture’s weight
while completing the wiring. Refer to the wiring diagram and attach the
fixture’s wires to the power supply wires from the junction box. Attach the
fixture’s wires to the power supply wires from the junction box. Connect Hot
to Hot (transparent wire with black inner thread, black, or smooth wire)
Neutral to Neutral (transparent wire with white inner thread, white, or
ribbedwire), and Ground to Ground (transparent wire with green inner thread,
green wire, or copper). Twist the ends of the wire pairs together, and then
twist on a wire connector. Make sure all twists are in the same direction. If
there is no house ground wire coming from the junction box, locate ground
screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground
wire around the ground screw. Use a screwdriver to tighten the top of ground
screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck
the wires into the junction box.
FINISHING THE INSTALLATION
(PLEASE NOTE: This fixture has multiple installation options. Before beginning, please review these instructions carefully.) TO INSTALL ON A WALL AND POWER THE FIXTURE USING THE PLUG REFER TO DIAGRAM
(1): 5. Hang the hole of mounting plate (B) behind the backplate (D) on the screws (C). Take cord (P) from backplate (D) and prepare for plugin. 6. Install a light bulb (not included) into socket (J) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. 7. Loosen thumbscrew (H) and move cap (I) up and then slide glass shade (L) up over socket (J) into cup (Q). 8. Move cap (I) down. Tighten thumbscrew (H) to secure. Your installation is now complete. 9. Plug-in cord (P) to your nearest outlet and twist knob (M) clockwise to turn on the fixture. To power the fixture off, twist the knob (M) counterclockwise. TO INSTALL OVER AN EXISTING JUNCTION BOX AND HARDWIRE THE FIXTURE REFER TODIAGRAM (2): 5. Place backplate (D) over mounting bracket (N) until mounting screws (A) protrude from the holes in backplate (D). Use deco nuts (G) to secure backplate (D) by threading deco nuts (G) onto the exposed threads of mounting screws (A). 6. Install a light bulb (not included) into socket (J) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. 7. Loosen thumbscrew (H) and move cap (I) up and then slide glass shade (L) up over socket (J) into cup (Q). 8. Move cap (I) down. Tighten thumbscrew (H) to secure. Your installation is now complete. 9. Twist knob (M) clockwise to turn on the fixture. To power the fixture off, twist the knob (M) counterclockwise.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>