MARVEL iPad Photobooth User Manual
- October 30, 2023
- Marvel
Table of Contents
MARVEL iPad Photobooth
Product Information
- This device complies with part 15 of the FCC rules.
- It is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
- This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Product Usage Instructions
- Ensure that the device is used in compliance with part 15 of the FCC rules.
- Do not use the device in a manner that may cause harmful interference.
- The device must accept any interference received, including interference that may cause undesired operation.
- Do not make any changes or modifications to the device that are not expressly approved by the party responsible for compliance.
- Ensure that the device is installed and operated with a minimum distance of 20cm between the radiator and your body to comply with FCC radiation exposure limits.
Attention
- Before using1 please check whether cables are damaged or stuck.
- Don’t shake too much.
- Place on level ground.
- Assemble Fixed Plate well to prevent iPad gets damaged.
- Children must be accompanied by an adult.
- Please take off the foot cups when put the photo booth into the flight case for transportation.
Component Introduction
The attachments received are subject to
lnstallation Guide
- Step 1 : Open the Simple Flight Case
- Step 2 : Assemble the base using Allen wrench
- Step 3 : Install Foot Cups
- Step 4 : Insert cable through Ring Light Bracket and plug to Body
- Step 5 : Fix Ring Light Bracket with screw driver
- Step 6 : Install the Cable Holder
- Step 7 : Open the door and plug the cable
- Step 8 : Remove the back plate on Swivel Bracket and install it to Ring Light Bracket
- Step 9 : Adjust the knob to control the tightness
- Step 1 o : Install the other part of Swivel Bracket to the back of Panel
- Step 11 : Fix your iPad on Panel with Fixed Plate
- Step 12 : Put on the back
- step 13 : Install Panel to Ring Light Bracket and screw it up
- Step 14 : Install the screw
- Step 15 :Plug the cable on Panel
- Step 16 : Plug the cable for power and ring light
0peration Instructions
Functions of RF Controller
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>