HINKLEY 41103 Series Wall Sconce Installation Guide

Item No: 41103,41104, 41503, 41504, 41603, 41604
Series Wall Sconce
Installation Guide

41103 Series Wall Sconce

DRAWING 1 – ASSEMBLY

DRAWING 2- JUNCTION BOX MOUNTING| DRAWING 3- NON-JUNCTION BOX MOUNTING
---|---

Assembly Instructions

start here
For junction box mounting:

1. To begin remove mounting plate (A) from backplate(C) by removing the four screws (E) located on the side of fixture see drawing 2.
2. Next determine which knockouts (K) need to be removed in order to secure mounting plate (A) to the junction box (J)
3. Use two 8-32 screws (not provided) (B) to secure mounting plate (A) to junction box (J)
4. Next assemble finial at bottom of fixture secure lock ups (L) on top of diffuser (D) and finial (F).
5. Connect black live wire (W) on fixture to supply wire inside junction box (X) using wire nuts provided
6. Connect white neutral wire (Z) on fixture to neutral wire inside junction box (Y) using wire nuts provided.
7. To ground fixture fasten ground wire to ground screw inside mounting plate
8. Attach backplate (C) to mounting plate using the four screws provided
9. Line up holes from backplate(C), shade (G), and diffuser (D).
10. Next screw in ball knobs (H) in those holes so that the backplate, shade and diffuser are all assembled

DRAWING 4 – WIRING

REPLACEMENT PARTS

41103

41104

41503

41504

41603

Part Letter

| Part number| Description|

QTY

---|---|---|---
V| EL2G16W7W1| 12″ LINEAR 16W LED BOARD| 2
G| SH003SLB| LONG OFF WHITE SLUB SHADE| 1
F| TC4162XX| LONG STEMS IN XX| 1
D| R41103DIF| LARGE AXIS SCONCE BOTTOM DIFFUSER| 1
D| R4003DIF| LARGE 2 HOLE TOP DIFFUSER| 1
H| K4001XX| TOP BARREL KNOB 8MMX8MM| 2
I| P4001STUD| THREDED STUD 1/2″| 2
L| K4003XX| BARREL KNOB 10MMx1OMM| 2

41604

DRAWING 1 – UNMOUNTING FIXTURE DRAWING 2 – LED REPLACEMENT DRAWING 3- WIRING LED

LED replacement Instructions

start here

1. To replace LED, first make sure that there is no power to the LED

2. To remove fixture from mounted location unscrew the four screws that hold backplate to mounting plate (Refer to drawing 1)

3. Disconnect both supply and neutral wires that connect the fixture to junction box or other power supply

4. Remove shade and diffusers from fixture so that LED is accessible (Refer to assembly Instructions on page 1)

5. Disconnect neutral and supply wires that connect the LED to the fixture . This can be done by pushing down on the push in connectors with a pen or small screwdriver, and simultaneously pulling the wires out. (Refer to drawing 3)

6. Remove defected LED by removing the small screws that hold in the LED board to the backplate

7.  To attach new LED board use hex nuts and screws that were used to attach the previous LED to the backplate.
   The gray thermal PAD that rested in-between the LED and backplate can be reused and should be placed between the new LED and backplate.(Refer to drawing 2)

8. Reconnect wires from the fixture to the new LED. This can be done by pushing down on the push in connectors with a pen or small screwdriver, and simultaneously pushing the wires into the connectors. (Refer to drawing 3)

9. Reassemble shade and diffusers onto fixture. (Refer to assembly Instructions on page 1)

10. Remount fixture to its original location and restore power. (Refer to drawing 1)

HINKLEY 33000 Pin Oak Parkway, Avon Lake,
OH 44012 800.446.5539 / 440.653.5500
hinkley.com

References

• HINKLEY - Lighting and Ceiling Fans

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>