johansson 4011 Optical Single or Dual or Triple Receiver User Manual
- June 4, 2024
- johansson
Table of Contents
Optical Single or Dual Triple Receiver
User Manual
4011 Optical Single or Dual or Triple Receiver
Ref. 4011 – 4012 – 4013
No part of this manual may be copied, reproduced, transmitted, transcribed or
translated into any language without permission.
Unitron reserves the right to change the specifications of the hardware and
software described in these manuals at any time.
Unitron cannot be held liable for any damages resulting from the use of this
product. Specifications are subject to change without notice. 8/20
© Unitron NV – Frankrijklaan 27 – B-8970 Poperinge – Belgium
T +32 57 33 33 63 F +32 57 33 45 24
sales@unitrongroup.com
www.unitrongroup.com
INTRODUCTION
Product Description
The optical receiver is developed for the transmission of broadband signals in
medium and large Fiber Optic systems. The Optical receiver can convert one,
two or three wavelengths. Ref. 4011 (Optical Single Receiver) converts 1550 nm
to Satellite or Terrestrial signal. Ref. 4012 (Optical Dual Receiver) converts
1310 + 1330 nm to wideband V/H; ef. 4013 (Optical Triple Receiver) converts
1310 + 1330 + 1550 nm to wideband V/H and Terrestrial signal.
- optical input level: -15 to +4 dBm
- frequency range: 5 – 2400 MHz
- high reception quality even with high split ratios
- powering via V or H output (12V – 20V)
- AGC to boost signal level
- optical wavelengths: 1310nm (V), 1330nm (H), 1550nm (T)
- compatible with Johansson wideband Multiswitches
- (e.g. 9775, 9754, 9758, 9734, etc.) with double F male adaptors
- or jumper cables
- up to 128 passive splits
INSTALLATION OF THE HARDWARE
Optical Single/Dual/Triple Receiver (Ref. 4011 – 4012 – 4013)
Optical Single/Dual/Triple Receiver (Ref. 4011 – 4012 – 4013)
TECHNICAL SPECIFICATIONS
| 4011| 4012| 4013
---|---|---|---
Optical inputs| –| 1
RF outputs*| –| 1| 2| 3
Optical wavelength| nm| 1550| 1310
1330| 1310
1330
1550
Frequency range TER| MHz| –| –| 5 – 1008
Frequency range SAT| MHz| 5 – 2400
Optical input level| dBm| – 15 to +4
AGC RF output level| dBµV| 80
Signal indicator| –| Green LED per wavelength
Return loss| dB| 10
Optical connector| –| SC/APC
RF connectors| –| 75 Ohm F type (Female)
Power consumption| W| 1| 2| 3
Power supply| VDC| 12 – 20 (via DC port)| 12 – 20 (via V or H port)
Power indicator| –| Green LED
Operating temperature range| °C| -20 to +55
Dimensions| mm| 36 x 45 x125| 36 x 45 x125| 56 x 45 x125
Weight| kg| 0.110| 0.110| 0.165
* Unused ports need to be terminated with 75 Ohm DC-blocked terminator
SAFETY INSTRUCTIONS
Read these instructions carefully before connecting the unit.
To prevent fire, short circuit, or shock hazards:
- Do not expose the unit to rain or moisture.
- Install the unit in a dry location without infiltration or condensation of water.
- Do not expose it to dripping or splashing.
- Do not place objects filled with liquids, such as vases, on the apparatus.
- If any liquid should accidentally falls into the cabinet, disconnect the power plug.
To avoid any risk of overheating:
- Install the unit in a well aery location and keep a minimum distance of 15 cm around the apparatus for sufficient ventilation
- Do not place any items such as newspapers, tablecloths, or curtains, on the unit that might cover the ventilation holes.
- Do not place any naked flame sources, such as lighted candles, on the apparatus
- Do not install the product in a dusty place
- Use the apparatus only in moderate climates (not in tropical climates)
- Respect the minimum and maximum temperature specifications
To avoid any risk of electrical shocks:
- Connect apparatus only to socket with protective earth connection.
- The mains plug shall remain readily operable
- Pull out the power plug to make the different connections of cables
- To avoid electrical shock, do not open the housing of the adapter.
Maintenance
Only use a dry soft cloth to clean the cabinet.
Do not use solvent
**** For repairing and servicing refer to qualified personnel.
Dispose of according to your local authority’s recycling processes.
CONDITIONS OF WARRANTY
Unitron N.V. warrants the product as being free from defects in material and
workmanship for a period of 24 months starting from the date of production
indicated on it. See note below. If during this period of warranty the product
proves defective, under normal use, due to defective materials or workmanship,
Unitron N.V, at its sole option, will repair or replace the product. Return
the product to your local dealer for reparation.
THE WARRANTY IS APPLIED ONLY FOR DEFECTS IN MATERIAL AND WORKMANSHIP AND
DOES NOT COVER DAMAGE RESULTING FROM:
- Misuse or use of the product out of its specifications,
- Installation or use in a manner inconsistent with the technical or safety standards in force in the country where the product is used,
- Use of non-suitable accessories (power supply, adapters…),
- installation in a defective system,
- External causes beyond the control of Unitron N.V. such as drops, accidents, lightning, water, fire, improper ventilation…
THE WARRANTY IS NOT APPLIED IF
- The production date or serial number on the product is illegible, altered, deleted or removed.
- The product has been opened or repaired by a non-authorized person.
NOTE
The date of production can be found in the product’s serial number code. The
format will either be “YEAR W WEEK” (e.g., 2017W32 = year 2017 week 32) or
“YYWW” (e.g., 1732 = year 2017 week 32).
UNITRON NV
Frankrijklaan 27
B-8970 Poperinge
Belgium
T +32 57 33 33 63
F +32 57 33 45 24
sales@unitrongroup.com
www.unitrongroup.com|
Dovozce:
Elektro HERINK s.r.o.
Wenzigova 79/8
301 00
Tel.: 377 222 255
Mobil: 606 615 292
obchod@elektroherink.cz
---|---
References
- UnitronGroup: Your Partner for Customized IP & RF Solutions
- UnitronGroup: Your Partner for Customized IP & RF Solutions
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>