Golden Lighting 1087-3P BCB-CLR Annette 3 Light Brushed Champagne Bronze Schoolhouse Pendant Light Instruction Manual
- June 12, 2024
- GOLDEN LIGHTING
Table of Contents
Golden Lighting 1087-3P BCB-CLR Annette 3 Light Brushed Champagne Bronze
Schoolhouse Pendant Light
Product Information
T he product is a lighting fixture manufactured by Golden Lighting. It is available in various models and styles to suit different lighting needs. The fixture is designed to provide both task and ambient lighting, enhancing the look and value of your home. The product can be coordinated with other fixtures like sconces, flush mounts, and pendants to create a layered lighting effect. It is recommended to install the lights with dimmers for better control over the light output.
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island:
Center a linear pendant over the kitchen island. If using hanging pendants,
use one pendant for every 24 inches of the island. The fixtures should hang at
least 30 inches above the countertop.
Pendants & Chandeliers Above a Dining Room Table:
The fixtures should be positioned at least 30 inches above the table. Choose
a fixture that is 12 inches narrower than the width of the table.
Pendants and Chandeliers in Open Areas:
The bottom of the fixture should hang at least 7.5 feet from the floor.
Make sure to allow clearance for any opening doors.
For installation and assembly instructions specific to the product model
1087-3P, please visit www.GoldenLighting.com.
If you require further assistance or replacement parts, please contact the
place of purchase for customer service.
INSTALLATION
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off? Follow us, share a picture, and tag us on Social…
Assembly Instructions
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
WiresNeutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. Take the mounting strap assembly from the parts bag.
Mounting strap (B) contains several threaded holes. Two sets of mounting
screws (A & C) should be attached to mounting strap (B). You may need to
tighten nuts (D) that hold mounting screws (A) in place. If the screws are not
attached, please hold canopy (F) up to mounting strap (B). Line up the holes
in canopy (F) with the holes in mounting strap (B) and insert mounting screws
(A) into mounting strap (B) so that mounting screws (A) protrude through the
holes in canopy (F). Mounting screws (A) are long, so please test the canopy
against the mounting strap to see how far you should insert the screws. Remove
the canopy and then tighten nuts (D) onto mounting screws (A) to hold the
screws in place. 2. Pull the house wire though the center of the mounting
strap (B). Place mounting strap (B) over the junction box and secure in place
with mounting screws (C). Tighten the screws securely with a screwdriver.
ASSEMBLING THE FIXTURE
3. Rods (H) are on the fixture’s wires, but not connected to the fixture.
Measure to determine the correct number of rods needed for proper hanging
height. Thread the fixture’s wires through rods (H) before threading the rods
together and then onto post (I). Connect rods (H) together and then to the
threads of swivel post of canopy (F). Tighten to secure using wrench tool if
necessary. To lengthen the fixture, add additional rods. If additional rods
are desired, contact the place of purchase to order. To shorten the fixture,
slide any excess rods off the fixture’s wires to discard. Trim the wires after
adding at least 8 to 10 inches of wire to the desired length. 4. Pass the ring
frame (K) and glass shade (M) up over the fixture and secure by threading
screws (J) through the holes in frame (K) into the holes in the fixture arms
(L).
CONNECTING THE WIRES
5. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
Get help, quick tips, and explore curated content
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>