CRYSTORAMA 4479-CH-CL-MWP Maria Theresa 12 Light Clear Italian Crystal Chandelier Instruction Manual
- June 12, 2024
- CRYSTORAMA
Table of Contents
CRYSTORAMA 4479-CH-CL-MWP Maria Theresa 12 Light Clear Italian Crystal
Chandelier
Product Information
The model number of the product is #4479-CH-CL-MWP. The fixture is dry-rated and requires 12-Candelabra Base Bulb. It is recommended to use 40 Watts bulbs, with a maximum limit of 60 Watts. LED bulbs are recommended for extended use. The product comes with various parts and components, including wire connector, mounting plate, outlet box screws, lock washer, hex nut, nipple, canopy, collar ring, collar loop, chain, ground wire, column, frame, metal dish, finial, candle sleeve, and rosette. There are different crystal sets available for installation, labeled as A to G. Each crystal set consists of a specific combination of crystals.
Product Usage Instructions
- Before starting the installation, do a complete inventory of all parts and components.
- Screw the column kit on the coupling.
- Place the glass dish and small metal dish over the bottom metal cover and secure with the finial.
- Attach the fixture into the outlet box and install bobeches and bulbs (not included).
- Connect the power after ensuring the fixture is safely attached.
- Start dressing the fixture with the packet labeled (A).
- Apply crystal sets in alphabetical order. The quantity and combination of crystals for each set are specified in the manual.
WARNING: All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes. Turn off the power before handling any electrical components.
ASSEMBLY INSTRUCTION
- MODEL #4479-CH-CL-MWP
WARNING
All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes.
You will need 12-Candelabra Base Bulb 40 Watts Recommended 60 Watts Max
DIMENSION
USE LED BULBS FOR EXTENDED USE
The fixture is dry rated
How to Install
- Do a complete inventory of all parts and components before you start installing.
- Screw the column kit on the coupling.
- Place the glass dish and small metal dish over the bottom metal cover and secure with the finial.
- After safety attaching the fixture into the outlet box, install bobeches, and bulbs (not included) and proceed to connecting the power.
- When you begin to dress the fixture, start with the packet labeled (A).
- IMPORTANT: Apply crystal sets in alphabetical order.
DETAILED ILLUSTRATION
Crystal Sets
- A. 52Sets. (1)14mm + AS20-2″
- B. 4Sets. AS20-2″(No Jewel)
- C. 8Sets. (1)14mm + AS20-3″
- D. 4Sets. (2)14mm + AS20-2.5″
- E. 24Sets. (1)14mm + AS20-2.5″
- F. 8Sets. (14)14mm
- G. 1Piece. (4)14mm + AS8-40mm Ball
WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer and/or birth defects or reproductive harm. For more information go to www.P65Warnings.ca.gov
Part Numbers
- A. (2)-Wire Connector
- B. (1)-Mounting Plate
- C. (2)-Outlet Box Screws
- D. (1)-Lock washer
- E. (1)-Hex Nut
- F. (1)-Nipple
- G. (1)-Canopy; w5″ x h1″ (XFB4474CHCAN5IN)
- H. (1)-Collar Ring
- I. (1)-Collar Loop
- J. (1)-Chain; 72″, 4mm (XFB4473CHCHA4MM)
- K. (1)-Ground Wire
- L. (1)-Column
- M. (1)-Frame
- N. (1)-Glass Dish; Ø4″, 17mm hole, 4pin (XFB4474CHDIBOB4IN)
- O. (1)-Metal Dish
- P. (1)-Finial (XFB4473CHFIN)
- Q. (12)-Candle Sleeve; h3″ (XFB4471CDL3IN)
- S. (12)-Bobeche; Ø4″, 26mm hole, 4pin (XFB4471CHBOB4IN)
- R. ( )-Rosette
- PART BAGⅠ: Includes Parts A, C
- PART BAG Ⅱ: Includes Parts B, D, E, F, H, I