LUTEC 6936704213 Outdoor Solar Lamp Post Light Owner’s Manual

LUTEC 6936704213 Outdoor Solar Lamp Post Light

Product Specifications

• Model: #6936704213
• Power Source: Solar panel
• Bulb Type: E12 LED (DC 3.5V 2W)
• Battery: 7.4V 2200mAh Li-ion

Product Usage Instructions

Preparation:

Before beginning assembly or installation, ensure all parts are present. Compare with the package contents and hardware contents lists. Do not proceed if any part is missing or damaged.

Installation:

1. Screw threaded rod (BB) into the solar panel top (A).
2. Attach the cap (AA) to the threaded rod (BB) by rotating clockwise.
3. Remove screws to detach the solar panel top (A) from the lamp head (B).
4. Install three bulbs (CC) to the solar panel top (A).
5. Turn ON the On/Off switch located under the solar panel top (A).
6. Attach solar panel top (A) to lamp head (B) using screws.
7. Secure the fixture to a pole using a set screw and a flathead screwdriver.

Battery Change:

1. Detach solar panel top (A) from lamp head (B).
2. Remove the battery cover screw and take out the old battery.
3. Install a new 7.4V 2200mAh Li-ion battery.
4. Reattach the battery cover and tighten it with a screwdriver.
5. Attach solar panel top (A) to lamp head (B) using screws.

Care and Maintenance:

Regularly check for any dirt or debris on the solar panel. Clean with a soft cloth if needed. Ensure the solar panel receives ample sunlight for optimal charging.

Troubleshooting

1. The battery is low or drained.

2. The light may be detecting daylight or light from another
   source.

3. The bulb is broken.

|

1. Charge the battery fully.
2. Relocate the light.
3. Change to a new LED bulb.

The light stays in low brightness, the battery does not fully
charge.|

1. If there are overcast days, the solar panel may not convert
   enough daylight.

2. There is not enough sunlight reaching the solar panel.

|

1. Wait for a sunny day for better charging.
2. Reposition the solar panel to receive more sunlight.

FAQs

• Q: How long does it take to fully charge the battery?
  • A: It is recommended to charge the light for 24 hours before first use for optimal performance.
• Q: What type of bulbs should be used with this lantern?
  • A: Use E12 LED bulbs with DC 3.5V 2W specifications for this lantern.

PACKAGE CONTENTS

HARDWARE CONTENTS

(not shown actual size)

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING:

• Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• Do not put the battery in fire – it may explode.
• Do not immerse into water.
• Do not expose the light to fire or intense heat as the battery may explode.
• The solar charger board should be set in a sunny area, where maximum sunlight can be collected. Typically, the solar board should face a direction (south) where sunlight can charge the board for at least 3 hours per day (5 hours per day if behind glass). It is suggested to charge the light for 24 hours before first use.

PREPARATION

Before beginning to assemble or install lighting fixtures, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product.

• Estimated Assembly Time : 10-20 minutes.
• Tools Required for Assembly : Flathead Screwdriver, Ladder.

INSTALLATION

1. Screw the threaded rod (BB) into the solar panel top (A).
2. Attach the cap (AA) to the threaded rod (BB) by rotating clockwise.
3. Remove the preassembled screws with a Phillips screwdriver (not included) to detach the solar panel top (A) from the lamp head (B).
4. Install the three bulbs (CC) to the solar panel top (A).
   • CAUTION : Only use this type of bulb: E12 LED (DC 3.5V 2W)
5. Turn ON the On/Off switch located on the underneath area of the solar panel top (A).
6. Attach the solar panel top (A) to the lamp head (B) by screwing the screws removed in step 3.
7. Attach the fixture to the pole (not included), then secure by tightening the set screw with a flathead screwdriver (not included).

BATTERY CHANGE

1. Remove the preassembled screws with a  Phillips screwdriver (not included) to detach the solar panel top (A) from the lamp head (B).

2. Remove the preassembled battery cover screw from the battery cover with a Phillips screwdriver (not included).
   Then remove the battery cover.

3. Take out the old battery from the battery compartment.
   CAUTION : Batteries must be recycled or destroyed appropriately.

4. Install a new battery (7.4 V 2200 mAh Li-ion).

5. Attach the battery cover to the solar panel top (A) with the battery cover screw removed in step 1.
   Tighten with a Phillips screwdriver (not included).

6. Attach the solar panel top (A) to the lamp head (B) by screwing the screws removed in step 1.

CARE AND MAINTENANCE

• To prolong the original appearance, clean the light fixture with clear water and a soft, damp cloth only.
• Periodically clean the solar panel with a soft cloth and warm water.
• Keep the panel clear of snow and leaves.
• Make sure trees and other objects do not block sunlight from the panel.
• Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature deterioration of the finish.
• This is not a defect in the finish and will not be covered by the warranty.
• Do not spray the light fixture with a hose or power washer.

TROUBLESHOOTING

3-YEAR LIMITED WARRANTY

If this product fails due to a defect in materials or workmanship within three (3) years from the date of purchase, return it along with proof of date of purchase and it will be replaced with the same or comparable model free of charge.
This warranty is void if damage or defect has resulted from accident, abuse, misuse, or faulty repair This warranty gives you specific legal rights and you may have other rights that vary from state to state.

IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OF ANY KIND ARISING OUT OF THE USE OR MISUSE OF THIS PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.

LUTEC USA LLC

• 149B Houston Rd Troutman NC 28166 Ningbo UTEC Electric Co., LTD
• CN8, Far East Industry Park, Yuyao, China
•   www.lutec.com
•   support@lutec.com

Please call our Customer Service line at 877-714-8669 for assistance Monday – Friday 9 a.m. to 5 p.m. EST

References

• Home | Lutec

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>